2.6.8.1 ES7000 subarch update
PATCH 1/1 2.6.8.1 ES7000 subarch update
Howdy -
The patch below adds hooks for the ES7000 Management Processor driver and implements an algorithm to determine an available GSI override for correctly mapping GSIs to IO-APIC pins. GSI overrides are required for the ES7000 platform since IRQ to pin mappings are NOT all one-to-one. This patch applies to the Unisys specific ES7000 machines. Extensive tests has been done on several models of the ES7000 to verify this patch.
Thanks,
Jason Davis
arch/i386/mach-es7000/es7000.h +0 -0
@@ -104,6 +104,13 @@
#define MIP_SW_APIC 0x1020b
#define MIP_FUNC(VALUE) (VALUE & 0xff)
+#if defined(CONFIG_X86_IO_APIC) && (defined(CONFIG_ACPI_INTERPRETER) || defined(CONFIG_ACPI_BOOT)) +#define IOAPIC_GSI_BOUND(ioapic) ((ioapic+1) * (nr_ioapic_registers[ioapic]-1)) +#define MAX_GSI_MAPSIZE 32
+#endif
+
+extern unsigned long io_apic_irqs;
+
extern int parse_unisys_oem (char *oemptr, int oem_entries);
extern int find_unisys_acpi_oem_table(unsigned long *oem_addr, int *length);
extern int es7000_start_cpu(int cpu, unsigned long eip);
arch/i386/mach-es7000/es7000plat.c +0 -0
@@ -51,27 +51,81 @@
int mip_port;
unsigned long mip_addr, host_addr;
+EXPORT_SYMBOL(mip_reg);
+EXPORT_SYMBOL(host_reg);
+EXPORT_SYMBOL(mip_port);
+EXPORT_SYMBOL(mip_addr);
+EXPORT_SYMBOL(host_addr);
+
+#if defined(CONFIG_X86_IO_APIC) && (defined(CONFIG_ACPI_INTERPRETER) || defined(CONFIG_ACPI_BOOT)) +static unsigned long cycle_irqs = 0;
+static unsigned long free_irqs = 0;
+static int gsi_map[MAX_GSI_MAPSIZE] = { [0 ... MAX_GSI_MAPSIZE-1] = -1 };
+
+/*
+ * GSI override for ES7000 platforms.
+ */
+
+static int __init
+es7000_gsi_override(int ioapic, int gsi)
+{
+ static int newgsi = 0;
+
+ if (gsi_map[gsi] != -1)
+ gsi = gsi_map[gsi];
+ else if (cycle_irqs ^ free_irqs)
+ {
+ newgsi = find_next_bit(&cycle_irqs, IOAPIC_GSI_BOUND(0), newgsi);
+ __set_bit(newgsi, &free_irqs);
+ gsi_map[gsi] = newgsi;
+ gsi = newgsi;
+ newgsi++;
+ Dprintk("es7000_gsi_override: free_irqs = 0x%lx\n", free_irqs);
+ }
+
+ return gsi;
+}
+
static int __inites7000_rename_gsi(int ioapic, int gsi)
{
- if (ioapic)
+ static int initialized = 0;
+ int i;
+
+ /*
+ * These should NEVER be true at this point but we'd rather be
+ * safe than sorry.
+ */
+ if (acpi_disabled || acpi_pci_disabled || acpi_noirq)
return gsi;
- else {
- if (gsi == 0)
- return 13;
- if (gsi == 1)
- return 16;
- if (gsi == 4)
- return 17;
- if (gsi == 6)
- return 18;
- if (gsi == 7)
- return 19;
- if (gsi == 8)
- return 20;
+
+ if (ioapic)
return gsi;
- }
+
+ if (!initialized) {
+ unsigned long tmp_irqs = 0;
+
+ for (i = 0; i < nr_ioapic_registers[0]; i++)
+ __set_bit(mp_irqs[i].mpc_srcbusirq, &tmp_irqs);
+
+ cycle_irqs = (~tmp_irqs & io_apic_irqs & ((1 << IOAPIC_GSI_BOUND(0)) - 1));
+
+ initialized = 1;
+ Dprintk("es7000_rename_gsi: cycle_irqs = 0x%lx\n", cycle_irqs);
+ }
+
+ for (i = 0; i < nr_ioapic_registers[0]; i++) {
+ if (mp_irqs[i].mpc_srcbusirq == gsi) {
+ if (mp_irqs[i].mpc_dstirq == gsi)
+ return gsi;
+ else
+ return es7000_gsi_override(0, gsi);
+ }
+ }
+
+ return gsi;
}
+#endif // (CONFIG_X86_IO_APIC) && (CONFIG_ACPI_INTERPRETER || CONFIG_ACPI_BOOT)
/*
* Parse the OEM Table
Review
Quoted 5 lines
(quoted diff) +5
-0+EXPORT_SYMBOL(mip_reg); +EXPORT_SYMBOL(host_reg); +EXPORT_SYMBOL(mip_port); +EXPORT_SYMBOL(mip_addr); +EXPORT_SYMBOL(host_addr);
There's no modular user of these anywhere in sight.
Review
Quoted 2 lines
(quoted diff) +2
-0+ else if (cycle_irqs ^ free_irqs) + {
wrong indentation.
Review
Quoted 8 lines · Jason Davis
int
mip_port;
unsigned longmip_addr,host_addr;(quoted diff) +5
-0+EXPORT_SYMBOL(mip_reg); +EXPORT_SYMBOL(host_reg); +EXPORT_SYMBOL(mip_port); +EXPORT_SYMBOL(mip_addr); +EXPORT_SYMBOL(host_addr);
This is asking for collisions with other modules. It would be a lot better for the future it these became e7000_mip_reg etc I think.
Quoted 4 lines · Alan Cox
Quoted 3 lines · Jason Davis
int
mip_port;
unsigned longmip_addr,host_addr;
Quoted 8 lines
Review
Quoted 5 lines
(quoted diff) +5
-0+EXPORT_SYMBOL(mip_reg); +EXPORT_SYMBOL(host_reg); +EXPORT_SYMBOL(mip_port); +EXPORT_SYMBOL(mip_addr); +EXPORT_SYMBOL(host_addr);This is asking for collisions with other modules. It would be a lot better for the future it these became
e7000_mip_regetc I think.
they seem to also be exclusively for a binary only kernel module..... hot topic.