Skip to contentSkip to conversation

cdrom recognition on kernel 2.6.8.1

DISCUSSION Lars Täuber 5 participants 5 messages Sep 15, 2004

lore
Share & tools
lore
#0 lore raw

Hallo everybody,

I'm not subscribed to this list! But I read the archive from time to time.

In my linux box is a teac IDE CD-Rom drive. This is only recognised when no audio cd is in the drive while booting. Is this a drive failure, or a kernel failure?

I didn't find any other on the net with the same problem. So hopefully someone of you can explain?

............
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller

    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA

libata version 1.02 loaded.
sata_sil version 0.54
ACPI: PCI interrupt 0000:01:07.0[A] -> GSI 11 (level, low) -> IRQ 11
............

best regards
Lars Täuber

#1 lore raw
Quoted 18 lines · Lars Täuber

Hallo everybody,

I'm not subscribed to this list! But I read the archive from time to time.

In my linux box is a teac IDE CD-Rom drive. This is only recognised when no audio cd is in the drive while booting. Is this a drive failure, or a kernel failure?

I didn't find any other on the net with the same problem. So hopefully someone of you can explain?

............
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller

Quoted 5 lines
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA

libata version 1.02 loaded.
sata_sil version 0.54
ACPI: PCI interrupt 0000:01:07.0[A] -> GSI 11 (level, low) -> IRQ 11
............

Did 2.6.7 work? The ide-probe isn't finding your drive, that's very odd. I think this is an issue with your hardware, not Linux. Perhaps you can use the drive if you add hdc=cdrom to your boot line.

Signature · 1 line
Jens Axboe
#2 lore raw

Dear Jens,

the problem accours also under 2.6.7.
But the hdc=cdrom options solves this problem (under 2.6.8.1):

..............
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller

    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA

hdc: ATAPI cdrom (?)
Using anticipatory io scheduler
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache
Uniform CD-ROM driver Revision: 3.20
..............

As written bevore the drive is not recognised only with an audio cd in it.

Thanks
Lars

Quoted 8 lines · On Wed, 15 Sep 2004 10:59:39 +0200 Jens Axboe <[email protected]> wrote:

Did 2.6.7 work? The ide-probe isn't finding your drive, that's very odd. I think this is an issue with your hardware, not Linux. Perhaps you can use the drive if you add hdc=cdrom to your boot line.

Signature · 1 line
Jens Axboe
Signature · 2 lines
Schöne Grüße
Lars Täuber
#3 lore raw
Quoted 5 lines · On Wed, 15 Sep 2004 19:15:32 +0200 Lars Täuber <[email protected]> wrote:

...

As written bevore the drive is not recognised only with an audio cd in it.

I've seen Teac drives blocking the Windows XP boot process when certain discs are inserted. There were even freezes when copying files to hard disk that did not occur when a different drive was used. (Wasn't my machine, can't test anything.)

Obviously Teac's firmware has some issues.

Regards

#4 lore raw

Salut,

Quoted 4 lines · Marc Ballarin

I've seen Teac drives blocking the Windows XP boot process when certain discs are inserted. There were even freezes when copying files to hard disk that did not occur when a different drive was used. (Wasn't my machine, can't test anything.)

I've had some issues with an old TEAC SCSI CD writer which was somewhat weird:

On bootup it would only read CDs if, after bootup had completed, one switched off its power and booted it again. (SCSI RESET was not sufficient.)

So yes.

Tonnerre