Skip to contentSkip to conversation

Bit by bit parallel port control

DISCUSSION Tony Howat 2 participants 2 messages Oct 11, 2004

lore
Share & tools
lore

Tony Howat

author
#0 lore raw

Hi Everyone,

I'm having problems controlling the parallel port on a bit-on bit-off basis for a relay switch on a control project.

Linux marmot 2.6.5-1.358 #1 Sat May 8 09:04:50 EDT 2004 i686 athlon i386 GNU/Linux

I have tried using the /dev/port method and putb - I can seemingly set bits on the port OK. However, checking with a meter shows the line changing for a few milliseconds then returning to 0v. I need the levels to hold. I believe that's what SHOULD happen...

I figured the lp module may interfere, so removed that. No help. Currently lsmod shows:

w83781d                26240  0
i2c_sensor              2176  1 w83781d
i2c_amd756              4484  0
i2c_core               16388  3 w83781d,i2c_sensor,i2c_amd756
autofs4                10624  0
sunrpc                101064  1
forcedeth              10624  0
floppy                 47440  0
sg                     27552  0
scsi_mod               91344  1 sg
dm_mod                 33184  0
ati_remote              9228  0
ohci_hcd               14748  0
button                  4504  0
battery                 6924  0
asus_acpi               8472  0
ac                      3340  0
ext3                  102376  3
jbd                    40216  1 ext3

Board is an ASUS A72N266VM (nforce based). Build is fedora 2. I'm not running lpd or X etc. Any suggestions?

There's plenty of sample code around, so I'm pretty confident I'm doing things right. My test code is here :

http://www.i-r-genius.com/paralleltest.c

I suspect there's something odd going on. I aim to try the code on an older machine soon.

Any help or pointers appreciated,

--
Tony

#1 lore raw

On Mon, 2004-10-11 15:10:13 +0100, Tony Howat <[email protected]> wrote in message <[email protected]>:

Quoted 4 lines

I have tried using the /dev/port method and putb - I can seemingly set bits on the port OK. However, checking with a meter shows the line changing for a few milliseconds then returning to 0v. I need the levels to hold. I believe that's what SHOULD happen...

Don't mess with the hardware on your own! That's almost always a bug and will cost you any later portability. Instead, just use the interface

Please use the userspace parport driver interface (provided by ppdev.ko). Additionally it'll give you full portability to non-PC hardware for free:-)

Quoted 4 lines

There's plenty of sample code around, so I'm pretty confident I'm doing things right. My test code is here :

http://www.i-r-genius.com/paralleltest.c

Not all that right:-) You access the hardware directly which is wrong. Use the ppdev interface instead.

I've just put the program online
(http://lug-owl.de/~jbglaw/software/steckdose/steckdose.c) which drives my relay box (basically a shift register + relay driver).

I guess the parport locking code isn't yet correct, but it should give you a start to using ppdev...

MfG, JBG

Signature · 4 lines
Jan-Benedict Glaw       [email protected]    . +49-172-7608481             _ O _
"Eine Freie Meinung in  einem Freien Kopf    | Gegen Zensur | Gegen Krieg  _ _ O
 fuer einen Freien Staat voll Freier Bürger" | im Internet! |   im Irak!   O O O
ret = do_actions((curr | FREE_SPEECH) & ~(NEW_COPYRIGHT_LAW | DRM | TCPA));