md and multipathing
Hello everyone!
I have a question concerning md driver: is there a way to have a multipath md that is mulitplexed? That is I have seen that when I create a multipath device, the device only uses on channel, always seems to be the first channel I use in the command line, to drive path even if I do not specify the second channel as a spare device?
I am using mdadm with 2.6.9 kernel.
mdadm --create --force -lmp -n2 /dev/md0 /dev/sda /dev/sdc
iostat always shows data flowing across only one channel as if the second device is in passive mode waiting for failover.
Thank you for your time.
Phy
__________________________________
Do you Yahoo!?
Yahoo! Mail Address AutoComplete - You start. We finish.
http://promotions.yahoo.com/new_mail
Quoted 2 lines · Phy Prabab
I have a question concerning md driver: is there a way to have a multipath md that is mulitplexed?
With 2.6, use the Device-Mapper multipath module.
Sincerely,
Lars Marowsky-Brée <[email protected]>
Signature · 3 lines
High Availability & Clustering SUSE Labs, Research and Development SUSE LINUX AG - A Novell company
Lars et all,
This what I am doing I believe. Here is the command:
mdadm --create --force -lmp -n2 /dev/md0 /dev/sda /dev/sdc
First controller is /dev/sda /dev/sdb (channel a and b respective) and the second controller is /dev/sdc /dev/sdd (again, channel a and b respecitve).
Here I am using multipath (enabled in kernel, 268,269,2610rc1) with the two paths to the FC volume. I have found that it only drives one channel of the md device as reported by vmstat. More over, the traffic appears to only go to the first device listed e.g. if I change the ordering and use channel "b" first, than all traffic to the md is driven on that channel.
Put another way, this is what I believe I have done:
device 0:0:0:0 + 1:0:0:0 = md0
device 0:0:0:1 + 1:0:0:1 = md1
scsi dev sda + sdc = md0
scsi dev sdb + sdd = md1
So have I done something wrong with the setup? Am I to question mdadm or md device?
I get the exact same behavior as if I were to make the device have a sprae path i.e. mdadm --create --force -lmp -n1 -x1 /dev/md0 /dev/sda /dev/sdc, but without the failover device. What I would want is to have traffice be "exqually balanced" across both channels (e.g. device paths /dev/sda /dev/sdc) with hopes that this will improve my throughput.
Thanks!
Phy
Quoted 4 lines · --- Lars Marowsky-Bree
Quoted 1 line · Phy Prabab
I have a question concerning md driver: is there a
Quoted 22 lines
way
Quoted 1 line
to have a multipath md that is mulitplexed?
With 2.6, use the Device-Mapper multipath module.
Sincerely,
Lars Marowsky-Brée <[email protected]>Signature · 11 lines
High Availability & Clustering SUSE Labs, Research and Development SUSE LINUX AG - A Novell company - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
__________________________________
Do you Yahoo!?
Yahoo! Mail Address AutoComplete - You start. We finish.
http://promotions.yahoo.com/new_mail