Skip to contentSkip to conversation

2.6.x libata updates

PATCH New Jeff Garzik 1 participant 1 message Nov 13, 2004

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 2.6.x libata updates

Please do a

bk pull bk://gkernel.bkbits.net/libata-2.6

This will update the following files:

 drivers/scsi/Kconfig        |   14 ++++----
 drivers/scsi/ahci.c         |   16 ++++-----
 drivers/scsi/ata_piix.c     |   16 +++++----
 drivers/scsi/libata-core.c  |   71 ++++++++++++++++++++++++--------------------
 drivers/scsi/libata-scsi.c  |    2 -
 drivers/scsi/libata.h       |    2 -
 drivers/scsi/sata_nv.c      |   13 ++++----
 drivers/scsi/sata_promise.c |   13 ++++----
 drivers/scsi/sata_sil.c     |    5 +--
 drivers/scsi/sata_sis.c     |    9 +++--
 drivers/scsi/sata_svw.c     |    5 +--
 drivers/scsi/sata_sx4.c     |   13 ++++----
 drivers/scsi/sata_uli.c     |    9 +++--
 drivers/scsi/sata_via.c     |    3 +
 drivers/scsi/sata_vsc.c     |    5 +--
 include/linux/libata.h      |   44 ++++++++++++++++++---------
 16 files changed, 141 insertions(+), 99 deletions(-)

through these ChangeSets:

<[email protected]> (04/11/13 1.2095)
[libata] bump versions, add MODULE_VERSION() tags

Also remove dep on CONFIG_EXPERIMENTAL for libata itself, and several libata drivers.

<[email protected]> (04/11/12 1.2094)
[libata] remove dependence on PCI

Most of this work was done by "Mat Loikkanen" <[email protected]>.

* use struct device rather than struct pci_dev
* use generic DMA routines (dma_xxx) and generic struct device routines (dev_xxx)
* isolate PCI-specific helpers inside CONFIG_PCI

drivers/scsi/Kconfig +7 -7
diff -Nru a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
@@ -399,7 +399,7 @@
 
 config SCSI_SATA
 	bool "Serial ATA (SATA) support"
-	depends on SCSI && EXPERIMENTAL
+	depends on SCSI
 	help
 	  This driver family supports Serial ATA host controllers
 	  and devices.
@@ -408,15 +408,15 @@
 
 config SCSI_SATA_AHCI
 	tristate "AHCI SATA support"
-	depends on SCSI_SATA && PCI && EXPERIMENTAL
+	depends on SCSI_SATA && PCI
 	help
 	  This option enables support for AHCI Serial ATA.
 
 	  If unsure, say N.
 
 config SCSI_SATA_SVW
-	tristate "ServerWorks Frodo / Apple K2 SATA support (EXPERIMENTAL)"
-	depends on SCSI_SATA && PCI && EXPERIMENTAL
+	tristate "ServerWorks Frodo / Apple K2 SATA support"
+	depends on SCSI_SATA && PCI
 	help
 	  This option enables support for Broadcom/Serverworks/Apple K2
 	  SATA support.
@@ -467,7 +467,7 @@
 
 config SCSI_SATA_SIS
 	tristate "SiS 964/180 SATA support"
-	depends on SCSI_SATA && PCI
+	depends on SCSI_SATA && PCI && EXPERIMENTAL
 	help
 	  This option enables support for SiS Serial ATA 964/180.
 
@@ -483,7 +483,7 @@
 
 config SCSI_SATA_VIA
 	tristate "VIA SATA support"
-	depends on SCSI_SATA && PCI && EXPERIMENTAL
+	depends on SCSI_SATA && PCI
 	help
 	  This option enables support for VIA Serial ATA.
 
@@ -491,7 +491,7 @@
 
 config SCSI_SATA_VITESSE
 	tristate "VITESSE VSC-7174 SATA support"
-	depends on SCSI_SATA && PCI && EXPERIMENTAL
+	depends on SCSI_SATA && PCI
 	help
 	  This option enables support for Vitesse VSC7174 Serial ATA.
 
drivers/scsi/ahci.c +8 -8
diff -Nru a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
@@ -270,7 +270,7 @@
 
 static int ahci_port_start(struct ata_port *ap)
 {
-	struct pci_dev *pdev = ap->host_set->pdev;
+	struct device *dev = ap->host_set->dev;
 	struct ahci_host_priv *hpriv = ap->host_set->private_data;
 	struct ahci_port_priv *pp;
 	int rc;
@@ -289,7 +289,7 @@
 	}
 	memset(pp, 0, sizeof(*pp));
 
-	mem = pci_alloc_consistent(pdev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma);
+	mem = dma_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma, GFP_KERNEL);
 	if (!mem) {
 		rc = -ENOMEM;
 		goto err_out_kfree;
@@ -353,7 +353,7 @@
 
 static void ahci_port_stop(struct ata_port *ap)
 {
-	struct pci_dev *pdev = ap->host_set->pdev;
+	struct device *dev = ap->host_set->dev;
 	struct ahci_port_priv *pp = ap->private_data;
 	void *mmio = ap->host_set->mmio_base;
 	void *port_mmio = ahci_port_base(mmio, ap->port_no);
@@ -370,8 +370,8 @@
 	msleep(500);
 
 	ap->private_data = NULL;
-	pci_free_consistent(pdev, AHCI_PORT_PRIV_DMA_SZ,
-			    pp->cmd_slot, pp->cmd_slot_dma);
+	dma_free_coherent(dev, AHCI_PORT_PRIV_DMA_SZ,
+			  pp->cmd_slot, pp->cmd_slot_dma);
 	kfree(pp);
 	ata_port_stop(ap);
 }
@@ -703,7 +703,7 @@
 static int ahci_host_init(struct ata_probe_ent *probe_ent)
 {
 	struct ahci_host_priv *hpriv = probe_ent->private_data;
-	struct pci_dev *pdev = probe_ent->pdev;
+	struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
 	void __iomem *mmio = probe_ent->mmio_base;
 	u32 tmp, cap_save;
 	u16 tmp16;
@@ -861,7 +861,7 @@
 static void ahci_print_info(struct ata_probe_ent *probe_ent)
 {
 	struct ahci_host_priv *hpriv = probe_ent->private_data;
-	struct pci_dev *pdev = probe_ent->pdev;
+	struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
 	void *mmio = probe_ent->mmio_base;
 	u32 vers, cap, impl, speed;
 	const char *speed_s;
@@ -965,7 +965,7 @@
 	}
 
 	memset(probe_ent, 0, sizeof(*probe_ent));
-	probe_ent->pdev = pdev;
+	probe_ent->dev = pci_dev_to_dev(pdev);
 	INIT_LIST_HEAD(&probe_ent->node);
 
 	mmio_base = ioremap(pci_resource_start(pdev, AHCI_PCI_BAR),
drivers/scsi/ata_piix.c +9 -7
diff -Nru a/drivers/scsi/ata_piix.c b/drivers/scsi/ata_piix.c
@@ -32,7 +32,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"ata_piix"
-#define DRV_VERSION	"1.02"
+#define DRV_VERSION	"1.03"
 
 enum {
 	PIIX_IOCFG		= 0x54, /* IDE I/O configuration register */
@@ -247,6 +247,7 @@
 MODULE_DESCRIPTION("SCSI low-level driver for Intel PIIX/ICH ATA controllers");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 /**
  *	piix_pata_cbl_detect - Probe host controller cable detect info
@@ -260,7 +261,7 @@
  */
 static void piix_pata_cbl_detect(struct ata_port *ap)
 {
-	struct pci_dev *pdev = ap->host_set->pdev;
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
 	u8 tmp, mask;
 
 	/* no 80c support in host controller? */
@@ -293,8 +294,9 @@
 
 static void piix_pata_phy_reset(struct ata_port *ap)
 {
-	if (!pci_test_config_bits(ap->host_set->pdev,
-				  &piix_enable_bits[ap->hard_port_no])) {
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+
+	if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->hard_port_no])) {
 		ata_port_disable(ap);
 		printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
 		return;
@@ -322,7 +324,7 @@
  */
 static int piix_sata_probe (struct ata_port *ap)
 {
-	struct pci_dev *pdev = ap->host_set->pdev;
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
 	int combined = (ap->flags & ATA_FLAG_SLAVE_POSS);
 	int orig_mask, mask, i;
 	u8 pcs;
@@ -392,7 +394,7 @@
 static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev)
 {
 	unsigned int pio	= adev->pio_mode - XFER_PIO_0;
-	struct pci_dev *dev	= ap->host_set->pdev;
+	struct pci_dev *dev	= to_pci_dev(ap->host_set->dev);
 	unsigned int is_slave	= (adev->devno != 0);
 	unsigned int master_port= ap->hard_port_no ? 0x42 : 0x40;
 	unsigned int slave_port	= 0x44;
@@ -444,7 +446,7 @@
 static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 {
 	unsigned int udma	= adev->dma_mode; /* FIXME: MWDMA too */
-	struct pci_dev *dev	= ap->host_set->pdev;
+	struct pci_dev *dev	= to_pci_dev(ap->host_set->dev);
 	u8 maslave		= ap->hard_port_no ? 0x42 : 0x40;
 	u8 speed		= udma;
 	unsigned int drive_dn	= (ap->hard_port_no ? 2 : 0) + adev->devno;
drivers/scsi/libata-core.c +40 -31

234 lines not on this page · raw message

drivers/scsi/libata-scsi.c +1 -1
diff -Nru a/drivers/scsi/libata-scsi.c b/drivers/scsi/libata-scsi.c
@@ -678,7 +678,7 @@
 			ata_sg_init_one(qc, cmd->request_buffer,
 					cmd->request_bufflen);
 
-		qc->pci_dma_dir = scsi_to_pci_dma_dir(cmd->sc_data_direction);
+		qc->dma_dir = cmd->sc_data_direction;
 	}
 
 	qc->complete_fn = ata_scsi_qc_complete;
drivers/scsi/libata.h +1 -1
diff -Nru a/drivers/scsi/libata.h b/drivers/scsi/libata.h
@@ -26,7 +26,7 @@
 #define __LIBATA_H__
 
 #define DRV_NAME	"libata"
-#define DRV_VERSION	"1.02"	/* must be exactly four chars */
+#define DRV_VERSION	"1.10"	/* must be exactly four chars */
 
 struct ata_scsi_args {
 	u16			*id;
drivers/scsi/sata_nv.c +8 -5
diff -Nru a/drivers/scsi/sata_nv.c b/drivers/scsi/sata_nv.c
@@ -44,7 +44,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME			"sata_nv"
-#define DRV_VERSION			"0.03"
+#define DRV_VERSION			"0.5"
 
 #define NV_PORTS			2
 #define NV_PIO_MASK			0x1f
@@ -234,6 +234,7 @@
 MODULE_DESCRIPTION("low-level driver for NVIDIA nForce SATA controller");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, nv_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 irqreturn_t nv_interrupt (int irq, void *dev_instance, struct pt_regs *regs)
 {
@@ -454,12 +455,13 @@
 
 static void nv_enable_hotplug_ck804(struct ata_probe_ent *probe_ent)
 {
+	struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
 	u8 intr_mask;
 	u8 regval;
 
-	pci_read_config_byte(probe_ent->pdev, NV_MCP_SATA_CFG_20, &regval);
+	pci_read_config_byte(pdev, NV_MCP_SATA_CFG_20, &regval);
 	regval |= NV_MCP_SATA_CFG_20_SATA_SPACE_EN;
-	pci_write_config_byte(probe_ent->pdev, NV_MCP_SATA_CFG_20, regval);
+	pci_write_config_byte(pdev, NV_MCP_SATA_CFG_20, regval);
 
 	writeb(NV_INT_STATUS_HOTPLUG, probe_ent->mmio_base + NV_INT_STATUS_CK804);
 
@@ -471,6 +473,7 @@
 
 static void nv_disable_hotplug_ck804(struct ata_host_set *host_set)
 {
+	struct pci_dev *pdev = to_pci_dev(host_set->dev);
 	u8 intr_mask;
 	u8 regval;
 
@@ -480,9 +483,9 @@
 
 	writeb(intr_mask, host_set->mmio_base + NV_INT_ENABLE_CK804);
 
-	pci_read_config_byte(host_set->pdev, NV_MCP_SATA_CFG_20, &regval);
+	pci_read_config_byte(pdev, NV_MCP_SATA_CFG_20, &regval);
 	regval &= ~NV_MCP_SATA_CFG_20_SATA_SPACE_EN;
-	pci_write_config_byte(host_set->pdev, NV_MCP_SATA_CFG_20, regval);
+	pci_write_config_byte(pdev, NV_MCP_SATA_CFG_20, regval);
 }
 
 static void nv_check_hotplug_ck804(struct ata_host_set *host_set)
drivers/scsi/sata_promise.c +7 -6
diff -Nru a/drivers/scsi/sata_promise.c b/drivers/scsi/sata_promise.c
@@ -40,7 +40,7 @@
 #include "sata_promise.h"
 
 #define DRV_NAME	"sata_promise"
-#define DRV_VERSION	"1.00"
+#define DRV_VERSION	"1.01"
 
 
 enum {
@@ -174,7 +174,7 @@
 
 static int pdc_port_start(struct ata_port *ap)
 {
-	struct pci_dev *pdev = ap->host_set->pdev;
+	struct device *dev = ap->host_set->dev;
 	struct pdc_port_priv *pp;
 	int rc;
 
@@ -189,7 +189,7 @@
 	}
 	memset(pp, 0, sizeof(*pp));
 
-	pp->pkt = pci_alloc_consistent(pdev, 128, &pp->pkt_dma);
+	pp->pkt = dma_alloc_coherent(dev, 128, &pp->pkt_dma, GFP_KERNEL);
 	if (!pp->pkt) {
 		rc = -ENOMEM;
 		goto err_out_kfree;
@@ -209,11 +209,11 @@
 
 static void pdc_port_stop(struct ata_port *ap)
 {
-	struct pci_dev *pdev = ap->host_set->pdev;
+	struct device *dev = ap->host_set->dev;
 	struct pdc_port_priv *pp = ap->private_data;
 
 	ap->private_data = NULL;
-	pci_free_consistent(pdev, 128, pp->pkt, pp->pkt_dma);
+	dma_free_coherent(dev, 128, pp->pkt, pp->pkt_dma);
 	kfree(pp);
 	ata_port_stop(ap);
 }
@@ -577,7 +577,7 @@
 	}
 
 	memset(probe_ent, 0, sizeof(*probe_ent));
-	probe_ent->pdev = pdev;
+	probe_ent->dev = pci_dev_to_dev(pdev);
 	INIT_LIST_HEAD(&probe_ent->node);
 
 	mmio_base = ioremap(pci_resource_start(pdev, 3),
@@ -661,6 +661,7 @@
 MODULE_DESCRIPTION("Promise SATA TX2/TX4 low-level driver");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, pdc_ata_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 module_init(pdc_ata_init);
 module_exit(pdc_ata_exit);
drivers/scsi/sata_sil.c +3 -2
diff -Nru a/drivers/scsi/sata_sil.c b/drivers/scsi/sata_sil.c
@@ -38,7 +38,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"sata_sil"
-#define DRV_VERSION	"0.54"
+#define DRV_VERSION	"0.8"
 
 enum {
 	sil_3112		= 0,
@@ -190,6 +190,7 @@
 MODULE_DESCRIPTION("low-level driver for Silicon Image SATA controller");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, sil_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 static void sil_post_set_mode (struct ata_port *ap)
 {
@@ -363,7 +364,7 @@
 
 	memset(probe_ent, 0, sizeof(*probe_ent));
 	INIT_LIST_HEAD(&probe_ent->node);
-	probe_ent->pdev = pdev;
+	probe_ent->dev = pci_dev_to_dev(pdev);
 	probe_ent->port_ops = sil_port_info[ent->driver_data].port_ops;
 	probe_ent->sht = sil_port_info[ent->driver_data].sht;
 	probe_ent->n_ports = (ent->driver_data == sil_3114) ? 4 : 2;
drivers/scsi/sata_sis.c +6 -3
diff -Nru a/drivers/scsi/sata_sis.c b/drivers/scsi/sata_sis.c
@@ -38,7 +38,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"sata_sis"
-#define DRV_VERSION	"0.10"
+#define DRV_VERSION	"0.5"
 
 enum {
 	sis_180			= 0,
@@ -128,6 +128,7 @@
 MODULE_DESCRIPTION("low-level driver for Silicon Integratad Systems SATA controller");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 static unsigned int get_scr_cfg_addr(unsigned int port_no, unsigned int sc_reg)
 {
@@ -140,22 +141,24 @@
 
 static u32 sis_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
 {
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
 	unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, sc_reg);
 	u32 val;
 
 	if (sc_reg == SCR_ERROR) /* doesn't exist in PCI cfg space */
 		return 0xffffffff;
-	pci_read_config_dword(ap->host_set->pdev, cfg_addr, &val);
+	pci_read_config_dword(pdev, cfg_addr, &val);
 	return val;
 }
 
 static void sis_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
 {
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
 	unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, scr);
 
 	if (scr == SCR_ERROR) /* doesn't exist in PCI cfg space */
 		return;
-	pci_write_config_dword(ap->host_set->pdev, cfg_addr, val);
+	pci_write_config_dword(pdev, cfg_addr, val);
 }
 
 static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg)
drivers/scsi/sata_svw.c +3 -2
diff -Nru a/drivers/scsi/sata_svw.c b/drivers/scsi/sata_svw.c
@@ -49,7 +49,7 @@
 #endif /* CONFIG_PPC_OF */
 
 #define DRV_NAME	"sata_svw"
-#define DRV_VERSION	"1.04"
+#define DRV_VERSION	"1.05"
 
 /* Taskfile registers offsets */
 #define K2_SATA_TF_CMD_OFFSET		0x00
@@ -376,7 +376,7 @@
 	}
 
 	memset(probe_ent, 0, sizeof(*probe_ent));
-	probe_ent->pdev = pdev;
+	probe_ent->dev = pci_dev_to_dev(pdev);
 	INIT_LIST_HEAD(&probe_ent->node);
 
 	mmio_base = ioremap(pci_resource_start(pdev, 5),
@@ -470,6 +470,7 @@
 MODULE_DESCRIPTION("low-level driver for K2 SATA controller");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, k2_sata_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 module_init(k2_sata_init);
 module_exit(k2_sata_exit);
drivers/scsi/sata_sx4.c +7 -6
diff -Nru a/drivers/scsi/sata_sx4.c b/drivers/scsi/sata_sx4.c
@@ -40,7 +40,7 @@
 #include "sata_promise.h"
 
 #define DRV_NAME	"sata_sx4"
-#define DRV_VERSION	"0.50"
+#define DRV_VERSION	"0.7"
 
 
 enum {
@@ -248,7 +248,7 @@
 
 static int pdc_port_start(struct ata_port *ap)
 {
-	struct pci_dev *pdev = ap->host_set->pdev;
+	struct device *dev = ap->host_set->dev;
 	struct pdc_port_priv *pp;
 	int rc;
 
@@ -263,7 +263,7 @@
 	}
 	memset(pp, 0, sizeof(*pp));
 
-	pp->pkt = pci_alloc_consistent(pdev, 128, &pp->pkt_dma);
+	pp->pkt = dma_alloc_coherent(dev, 128, &pp->pkt_dma, GFP_KERNEL);
 	if (!pp->pkt) {
 		rc = -ENOMEM;
 		goto err_out_kfree;
@@ -283,11 +283,11 @@
 
 static void pdc_port_stop(struct ata_port *ap)
 {
-	struct pci_dev *pdev = ap->host_set->pdev;
+	struct device *dev = ap->host_set->dev;
 	struct pdc_port_priv *pp = ap->private_data;
 
 	ap->private_data = NULL;
-	pci_free_consistent(pdev, 128, pp->pkt, pp->pkt_dma);
+	dma_free_coherent(dev, 128, pp->pkt, pp->pkt_dma);
 	kfree(pp);
 	ata_port_stop(ap);
 }
@@ -1397,7 +1397,7 @@
 	}
 
 	memset(probe_ent, 0, sizeof(*probe_ent));
-	probe_ent->pdev = pdev;
+	probe_ent->dev = pci_dev_to_dev(pdev);
 	INIT_LIST_HEAD(&probe_ent->node);
 
 	mmio_base = ioremap(pci_resource_start(pdev, 3),
@@ -1492,6 +1492,7 @@
 MODULE_DESCRIPTION("Promise SATA low-level driver");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, pdc_sata_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 module_init(pdc_sata_init);
 module_exit(pdc_sata_exit);
drivers/scsi/sata_uli.c +6 -3
diff -Nru a/drivers/scsi/sata_uli.c b/drivers/scsi/sata_uli.c
@@ -32,7 +32,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"sata_uli"
-#define DRV_VERSION	"0.11"
+#define DRV_VERSION	"0.2"
 
 enum {
 	uli_5289		= 0,
@@ -123,6 +123,7 @@
 MODULE_DESCRIPTION("low-level driver for ULi Electronics SATA controller");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, uli_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 static unsigned int get_scr_cfg_addr(unsigned int port_no, unsigned int sc_reg)
 {
@@ -149,18 +150,20 @@
 
 static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
 {
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
 	unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, sc_reg);
 	u32 val;
 
-	pci_read_config_dword(ap->host_set->pdev, cfg_addr, &val);
+	pci_read_config_dword(pdev, cfg_addr, &val);
 	return val;
 }
 
 static void uli_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
 {
+	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
 	unsigned int cfg_addr = get_scr_cfg_addr(ap->port_no, scr);
 
-	pci_write_config_dword(ap->host_set->pdev, cfg_addr, val);
+	pci_write_config_dword(pdev, cfg_addr, val);
 }
 
 static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg)
drivers/scsi/sata_via.c +2 -1
diff -Nru a/drivers/scsi/sata_via.c b/drivers/scsi/sata_via.c
@@ -38,7 +38,7 @@
 #include <asm/io.h>
 
 #define DRV_NAME	"sata_via"
-#define DRV_VERSION	"0.20"
+#define DRV_VERSION	"1.0"
 
 enum {
 	via_sata		= 0,
@@ -138,6 +138,7 @@
 MODULE_DESCRIPTION("SCSI low-level driver for VIA SATA controllers");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, svia_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 static u32 svia_scr_read (struct ata_port *ap, unsigned int sc_reg)
 {
drivers/scsi/sata_vsc.c +3 -2
diff -Nru a/drivers/scsi/sata_vsc.c b/drivers/scsi/sata_vsc.c
@@ -26,7 +26,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"sata_vsc"
-#define DRV_VERSION	"0.01"
+#define DRV_VERSION	"1.0"
 
 /* Interrupt register offsets (from chip base address) */
 #define VSC_SATA_INT_STAT_OFFSET	0x00
@@ -293,7 +293,7 @@
 		goto err_out_regions;
 	}
 	memset(probe_ent, 0, sizeof(*probe_ent));
-	probe_ent->pdev = pdev;
+	probe_ent->dev = pci_dev_to_dev(pdev);
 	INIT_LIST_HEAD(&probe_ent->node);
 
 	mmio_base = ioremap(pci_resource_start(pdev, 0),
@@ -393,6 +393,7 @@
 MODULE_DESCRIPTION("low-level driver for Vitesse VSC7174 SATA controller");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, vsc_sata_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
 
 module_init(vsc_sata_init);
 module_exit(vsc_sata_exit);
include/linux/libata.h +30 -14

107 lines not on this page · raw message