powernow-k8 problem (Mobile Sempron 2800+, Acer Aspire 1362)

Hello,

I'm sorry, in previous e-mail I have attached too short part of log (Having had compiled debug enabled module powernow-k8).

On modprobe I get:

powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09e)
powernow-k8:    0 : fid 0x8, vid 0x6
powernow-k8:    1 : fid 0x0, vid 0x18
powernow-k8:    0 : fid 0x8 (1600 MHz), vid 0x6 (1400 mV)
powernow-k8:    1 : fid 0x0 (800 MHz), vid 0x18 (950 mV)
powernow-k8: cpu0, init lo 0x408, hi 0x1
powernow-k8: policy current frequency 1600000 kHz
powernow-k8: cpu_init done, current fid 0x8, vid 0x4
powernow-k8: targ: cpu 0, 1600000 kHz, min 800000, max 1600000, relation 0
powernow-k8: targ: curr fid 0x8, vid 0x4
powernow-k8: cpu 0 transition to index 0
powernow-k8: table matched fid 0x8, giving vid 0x6
powernow-k8: cpu 0, changing to fid 0x8, vid 0x6
powernow-k8: ph1 (cpu0): start, currfid 0x8, currvid 0x4, reqvid 0x6, rvo 0x2
powernow-k8: ph1: changing vid for rvo, req 0x3
powernow-k8: writing vid 0x3, lo 0x10308, hi 0x1
powernow-k8: vid trans failed, vid 0x3, curr 0x4
powernow-k8: transition frequency failed

when powernowd starts it is followed by:

owernow-k8: targ: cpu 0, 1500000 kHz, min 800000, max 1600000, relation 0
powernow-k8: targ: curr fid 0x8, vid 0x4
powernow-k8: cpu 0 transition to index 0
powernow-k8: table matched fid 0x8, giving vid 0x6
powernow-k8: cpu 0, changing to fid 0x8, vid 0x6
powernow-k8: ph1 (cpu0): start, currfid 0x8, currvid 0x4, reqvid 0x6, rvo 0x2
powernow-k8: ph1: changing vid for rvo, req 0x3
powernow-k8: writing vid 0x3, lo 0x10308, hi 0x1
powernow-k8: vid trans failed, vid 0x3, curr 0x4
powernow-k8: transition frequency failed
powernow-k8: targ: cpu 0, 1400000 kHz, min 800000, max 1600000, relation 0
powernow-k8: targ: curr fid 0x8, vid 0x4
powernow-k8: cpu 0 transition to index 0
powernow-k8: table matched fid 0x8, giving vid 0x6
powernow-k8: cpu 0, changing to fid 0x8, vid 0x6
powernow-k8: ph1 (cpu0): start, currfid 0x8, currvid 0x4, reqvid 0x6, rvo 0x2
powernow-k8: ph1: changing vid for rvo, req 0x3
powernow-k8: writing vid 0x3, lo 0x10308, hi 0x1
powernow-k8: vid trans failed, vid 0x3, curr 0x4
powernow-k8: transition frequency failed
powernow-k8: targ: cpu 0, 1300000 kHz, min 800000, max 1600000, relation 0
powernow-k8: targ: curr fid 0x8, vid 0x4
powernow-k8: cpu 0 transition to index 0
powernow-k8: table matched fid 0x8, giving vid 0x6
powernow-k8: cpu 0, changing to fid 0x8, vid 0x6
powernow-k8: ph1 (cpu0): start, currfid 0x8, currvid 0x4, reqvid 0x6, rvo 0x2
powernow-k8: ph1: changing vid for rvo, req 0x3
powernow-k8: writing vid 0x3, lo 0x10308, hi 0x1
powernow-k8: vid trans failed, vid 0x3, curr 0x4
powernow-k8: transition frequency failed
powernow-k8: targ: cpu 0, 1200000 kHz, min 800000, max 1600000, relation 0
powernow-k8: targ: curr fid 0x8, vid 0x4
powernow-k8: cpu 0 transition to index 0
powernow-k8: table matched fid 0x8, giving vid 0x6
powernow-k8: cpu 0, changing to fid 0x8, vid 0x6
powernow-k8: ph1 (cpu0): start, currfid 0x8, currvid 0x4, reqvid 0x6, rvo 0x2
powernow-k8: ph1: changing vid for rvo, req 0x3
powernow-k8: writing vid 0x3, lo 0x10308, hi 0x1
powernow-k8: vid trans failed, vid 0x3, curr 0x4
powernow-k8: transition frequency failed
powernow-k8: targ: cpu 0, 1100000 kHz, min 800000, max 1600000, relation 0
powernow-k8: targ: curr fid 0x8, vid 0x4
powernow-k8: cpu 0 transition to index 0
powernow-k8: table matched fid 0x8, giving vid 0x6
powernow-k8: cpu 0, changing to fid 0x8, vid 0x6
powernow-k8: ph1 (cpu0): start, currfid 0x8, currvid 0x4, reqvid 0x6, rvo 0x2
powernow-k8: ph1: changing vid for rvo, req 0x3
powernow-k8: writing vid 0x3, lo 0x10308, hi 0x1
powernow-k8: vid trans failed, vid 0x3, curr 0x4
powernow-k8: transition frequency failed
powernow-k8: targ: cpu 0, 1000000 kHz, min 800000, max 1600000, relation 0
powernow-k8: targ: curr fid 0x8, vid 0x4
powernow-k8: cpu 0 transition to index 0
powernow-k8: table matched fid 0x8, giving vid 0x6
powernow-k8: cpu 0, changing to fid 0x8, vid 0x6
powernow-k8: ph1 (cpu0): start, currfid 0x8, currvid 0x4, reqvid 0x6, rvo 0x2
powernow-k8: ph1: changing vid for rvo, req 0x3
powernow-k8: writing vid 0x3, lo 0x10308, hi 0x1
powernow-k8: vid trans failed, vid 0x3, curr 0x4
powernow-k8: transition frequency failed
powernow-k8: targ: cpu 0, 900000 kHz, min 800000, max 1600000, relation 0
powernow-k8: targ: curr fid 0x8, vid 0x4
powernow-k8: cpu 0 transition to index 0
powernow-k8: table matched fid 0x8, giving vid 0x6
powernow-k8: cpu 0, changing to fid 0x8, vid 0x6
powernow-k8: ph1 (cpu0): start, currfid 0x8, currvid 0x4, reqvid 0x6, rvo 0x2
powernow-k8: ph1: changing vid for rvo, req 0x3
powernow-k8: writing vid 0x3, lo 0x10308, hi 0x1
powernow-k8: vid trans failed, vid 0x3, curr 0x4
powernow-k8: transition frequency failed
powernow-k8: targ: cpu 0, 800000 kHz, min 800000, max 1600000, relation 0
powernow-k8: targ: curr fid 0x8, vid 0x4
powernow-k8: cpu 0 transition to index 1
powernow-k8: table matched fid 0x0, giving vid 0x18
powernow-k8: cpu 0, changing to fid 0x0, vid 0x18
powernow-k8: ph1 (cpu0): start, currfid 0x8, currvid 0x4, reqvid 0x18, rvo 0x2
powernow-k8: ph1: changing vid for rvo, req 0x3
powernow-k8: writing vid 0x3, lo 0x10308, hi 0x1
powernow-k8: vid trans failed, vid 0x3, curr 0x4
powernow-k8: transition frequency failed

All suggestions on making it work are welcome,
Thanks in advance,
Michał

P.S.
1. Well, IMHO frequencies are read properly, it is a problem of VID, I can't figure out why writting 0x3 is attempted... (since above I see propper values, I guess...)
2. Above conditions occured in linux gentoo, kernel 2.6.9 as well as 2.6.10-rc1 (plain as well as patched by gentoo), Acer Aspire1362 laptop. gcc 3.4.3, PowerNow Daemon v0.90hun6