Skip to contentSkip to conversation

Reading BIOS

DISCUSSION Jagadeesh Bhaskar P 3 participants 4 messages Nov 25, 2004 – Nov 27, 2004

lore
Share & tools
lore
#0 lore raw

Hi,
Is it possible to probe for, say, ide controllers from the BIOS, CMOS information with a C program? Is there any documentation available regarding the same??

Signature · 7 lines
With regards,

Jagadeesh Bhaskar P
R&D Engineer
HCL Infosystems Ltd
Pondicherry
INDIA
#1 lore raw

On Thu, 2004-11-25 14:04:32 +0530, Jagadeesh Bhaskar P <[email protected]> wrote in message <1101371672.3795.36.camel@myLinux>:

Quoted 4 lines

Hi,
Is it possible to probe for, say, ide controllers from the BIOS, CMOS information with a C program? Is there any documentation available regarding the same??

Well, you don't really want to fiddle with physical addresses from within userspace programs while running a protected-mode operating system:-)

If you only want to know the type of IDE controller, and if your hardware wasn't build during stone age, it's probably as simple as reading the IDE controller's PCI device IDs. There's a libpci available for Linux which helps you doing this (because there are different access methods for accessing the PCI busses).

'lspci' for example uses it, probably parsing lspci's output is just enough for your job...

MfG, JBG

Signature · 4 lines
Jan-Benedict Glaw       [email protected]    . +49-172-7608481             _ O _
"Eine Freie Meinung in  einem Freien Kopf    | Gegen Zensur | Gegen Krieg  _ _ O
 fuer einen Freien Staat voll Freier Bürger" | im Internet! |   im Irak!   O O O
ret = do_actions((curr | FREE_SPEECH) & ~(NEW_COPYRIGHT_LAW | DRM | TCPA));
#2 lore raw

Can anybody give references to interpret the output of *lspci* command

Thanks In Advance
K.Ananth

Quoted 28 lines · Jan-Benedict Glaw

On Thu, 2004-11-25 14:04:32 +0530, Jagadeesh Bhaskar P <[email protected]> wrote in message <1101371672.3795.36.camel@myLinux>:

Quoted 6 lines

Hi,
Is it possible to probe for, say, ide controllers from the BIOS, CMOS information with a C program? Is there any documentation available regarding the same??

Well, you don't really want to fiddle with physical addresses from within userspace programs while running a protected-mode operating system:-)

If you only want to know the type of IDE controller, and if your hardware wasn't build during stone age, it's probably as simple as reading the IDE controller's PCI device IDs. There's a libpci available for Linux which helps you doing this (because there are different access methods for accessing the PCI busses).

'lspci' for example uses it, probably parsing lspci's output is just enough for your job...

MfG, JBG

#3 lore raw

On Sat, 2004-11-27 15:13:01 +0530, K. Anantha Kiran <[email protected]> wrote in message <[email protected]>:

Quoted 1 line

Can anybody give references to interpret the output of *lspci* command

Well, you'd just look at lspci's sources to see what it outputs. Please don't try to push simple research work to others... Also, this requires some knowledge of what PCI actually is and how it works.

MfG, JBG

Signature · 4 lines
Jan-Benedict Glaw       [email protected]    . +49-172-7608481             _ O _
"Eine Freie Meinung in  einem Freien Kopf    | Gegen Zensur | Gegen Krieg  _ _ O
 fuer einen Freien Staat voll Freier Bürger" | im Internet! |   im Irak!   O O O
ret = do_actions((curr | FREE_SPEECH) & ~(NEW_COPYRIGHT_LAW | DRM | TCPA));