device not accepting address / timeout
hi,
I encountered some problems connecting a usb-scanner (usb2). Since I found only postings in newgroups that report similar problems but no solution, I hope someone here can help.
OS: Debian Sarge
Tested Kernels: 2.6.9, 2.6.10-rc1, 2.6.10-rc3
Usb output of dmesg:
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0ehci_hcd 0000:00:10.3: reset hcs_params 0x2204 dbg=0 cc=2 pcc=2 ordered !ppc ports=4ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes 256/512/1024 ehci_hcd 0000:00:10.3: capability 0001 at 68ehci_hcd 0000:00:10.3: irq 21, pci mem 0xdfffff00ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALTehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256 RUN ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 ehci_hcd 0000:00:10.3: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: default language 0x0409
usb usb1: Product: VIA Technologies, Inc. USB 2.0
usb usb1: Manufacturer: Linux 2.6.10-rc1 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all portsehci_hcd 0000:00:10.3: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501 ehci_hcd 0000:00:10.3: port 4 high speedehci_hcd 0000:00:10.3: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new high speed USB device using address 2
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controlleruhci_hcd 0000:00:10.0: irq 21, io base 0xe800uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: detected 2 ports
[....]
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: default language 0x0409
usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
usb usb3: Manufacturer: Linux 2.6.10-rc1 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is gooduhci_hcd 0000:00:10.0: suspend_hcuhci_hcd 0000:00:10.1: suspend_hc
usb 1-4: control timeout on ep0inehci_hcd 0000:00:10.3: devpath 4 ep0out 3strikesehci_hcd 0000:00:10.3: devpath 4 ep0out 3strikes
usb 1-4: device not accepting address 2, error -71
hub 1-0:1.0: port 4 not reset yet, waiting 50msehci_hcd 0000:00:10.3: port 4 high speedehci_hcd 0000:00:10.3: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new high speed USB device using address 3
usb 1-4: control timeout on ep0in <------------------------ehci_hcd 0000:00:10.3: devpath 4 ep0out 3strikesehci_hcd 0000:00:10.3: devpath 4 ep0out 3strikes
usb 1-4: device not accepting address 3, error -71 <--------uhci_hcd 0000:00:10.0: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 uhci_hcd 0000:00:10.0: port 2 portsc 008a,00
hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 uhci_hcd 0000:00:10.1: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 uhci_hcd 0000:00:10.1: port 2 portsc 009a,00
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 ehci_hcd 0000:00:10.3: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501 hub 1-0:1.0: port 4 not reset yet, waiting 50msehci_hcd 0000:00:10.3: port 4 high speedehci_hcd 0000:00:10.3: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new high speed USB device using address 4
[.....]
lsusb reports:
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
although the scanner is connected.
Other usb-devices such as memory sticks work normaly. I tried to disable ehci but this didn't improve the situation. And the scanner already worked successfully with a 2.4 kernel a year ago.
Hope someone can clear up.
TIA.
Alex
Hi Alexander!
I have the same problem with Debian unstable, kernel 2.6.10-rc2-mm3 and uhci-hcd (usb1). It affects my keyboard and mouse :-(
pci=noacpi solved the problem for me. Else the interrupt count on IRQ#10 stayed at zero and nothing worked. pci=routeirq did not help.
Quoted 137 lines · Alexander Dressler
hi,
I encountered some problems connecting a usb-scanner (usb2). Since I found only postings in newgroups that report similar problems but no solution, I hope someone here can help.
OS: Debian Sarge
Tested Kernels: 2.6.9, 2.6.10-rc1, 2.6.10-rc3Usb output of dmesg:
ehci_hcd0000:00:10.3: VIA Technologies, Inc. USB 2.0ehci_hcd0000:00:10.3: resethcs_params0x2204dbg=0 cc=2 pcc=2 ordered !ppc ports=4ehci_hcd0000:00:10.3: resethcc_params6872 thresh 7 uframes 256/512/1024ehci_hcd0000:00:10.3: capability 0001 at 68ehci_hcd0000:00:10.3: irq 21, pci mem0xdfffff00ehci_hcd0000:00:10.3: new USB bus registered, assigned bus number 1ehci_hcd0000:00:10.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALTehci_hcd0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256 RUNehci_hcd0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10ehci_hcd0000:00:10.3: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: default language0x0409
usb usb1: Product: VIA Technologies, Inc. USB 2.0
usb usb1: Manufacturer: Linux 2.6.10-rc1ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0:usb_probe_interface
hub 1-0:1.0:usb_probe_interface- got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all portsehci_hcd0000:00:10.3: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status0x501ehci_hcd0000:00:10.3: port 4 high speedehci_hcd0000:00:10.3: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new high speed USB device using address 2
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5uhci_hcd0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controlleruhci_hcd0000:00:10.0: irq 21, io base0xe800uhci_hcd0000:00:10.0: new USB bus registered, assigned bus number 2uhci_hcd0000:00:10.0: detected 2 ports
[....]
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: default language0x0409
usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
usb usb3: Manufacturer: Linux 2.6.10-rc1uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0:usb_probe_interface
hub 3-0:1.0:usb_probe_interface- got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is gooduhci_hcd0000:00:10.0:suspend_hcuhci_hcd0000:00:10.1:suspend_hc
usb 1-4: control timeout on ep0inehci_hcd0000:00:10.3: devpath 4 ep0out 3strikesehci_hcd0000:00:10.3: devpath 4 ep0out 3strikes
usb 1-4: device not accepting address 2, error -71
hub 1-0:1.0: port 4 not reset yet, waiting 50msehci_hcd0000:00:10.3: port 4 high speedehci_hcd0000:00:10.3: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new high speed USB device using address 3
usb 1-4: control timeout on ep0in <------------------------ehci_hcd0000:00:10.3: devpath 4 ep0out 3strikesehci_hcd0000:00:10.3: devpath 4 ep0out 3strikes
usb 1-4: device not accepting address 3, error -71 <--------uhci_hcd0000:00:10.0: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status0x100uhci_hcd0000:00:10.0: port 2 portsc 008a,00
hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status0x100uhci_hcd0000:00:10.1: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status0x100uhci_hcd0000:00:10.1: port 2 portsc 009a,00
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status0x100ehci_hcd0000:00:10.3: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status0x501hub 1-0:1.0: port 4 not reset yet, waiting 50msehci_hcd0000:00:10.3: port 4 high speedehci_hcd0000:00:10.3: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 1-4: new high speed USB device using address 4
[.....]lsusb reports:
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
although the scanner is connected.Other usb-devices such as memory sticks work normaly. I tried to disable ehci but this didn't improve the situation. And the scanner already worked successfully with a 2.4 kernel a year ago.
Hope someone can clear up.
TIA.
Alex
Quoted 6 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Ciao,
Roland
--
TU Muenchen, Physik-Department E18, James-Franck-Str. 85747 Garching Telefon 089/289-12592; Telefax 089/289-12570
--
A mouse is a device used to point at
the xterm you want to type in.
Kim Alm on a.s.r.