Skip to contentSkip to conversation

Promise module (old) broken

DISCUSSION [email protected] 3 participants 3 messages Dec 5, 2004

lore
Share & tools
lore
#0 lore raw

Hi,

up to the actual kernel rc 2.6.10rc3 has broken pdc 20265 support. As
some kernel releases ago, one had to specify i/o ports on kernel cmdline. 2.4.28 kernel works w/o cmdline parameter.

Is this behaviour intended? Will it be fixed in 2.6.10 release?

W/o parameter kernel (2.6) does not recognise the pdc ide controller drives.
dmesg output states: "ideX: Wait for ready failed before probe !"

As of kernel rc 2.6.10rc1 the kernel even reported ide drive short read and seek errors on drives even not connected to the pdc controller but connected to the onboard controller (->/dev/hda1). In fact /dev/hda1 has no errors (so far).

Any comments?

Thanks.

Nils

Signature · 5 lines
*     lkml@                 * University of Stuttgart *    icq / lc   *
*      www.Think-Future.de  *    dep.comp.science     * 9336272/92045 *
:x                                                                   :)

   All power corrupts, but we need electricity. 
#1 lore raw
Quoted 7 lines · On Sun, 5 Dec 2004 18:54:00 +0100, [email protected] <[email protected]>…

Hi,

up to the actual kernel rc 2.6.10rc3 has broken pdc 20265 support. As
some kernel releases ago, one had to specify i/o ports on kernel cmdline. 2.4.28 kernel works w/o cmdline parameter.

Is this behaviour intended? Will it be fixed in 2.6.10 release?

Haven't you forgot to compile in pdc202xx_old driver?

Quoted 10 lines

W/o parameter kernel (2.6) does not recognise the pdc ide controller drives.
dmesg output states: "ideX: Wait for ready failed before probe !"

As of kernel rc 2.6.10rc1 the kernel even reported ide drive short read and seek errors on drives even not connected to the pdc controller but connected to the onboard controller (->/dev/hda1). In fact /dev/hda1 has no errors (so far).

Any comments?

Read REPORTING-BUGS from the kernel source package and give us at least dmesgs and configs.

#2 lore raw
In reply to [email protected]
Quoted 12 lines · On Sun, 5 Dec 2004 18:54:00 +0100, [email protected] <[email protected]>…

Hi,

up to the actual kernel rc 2.6.10rc3 has broken pdc 20265 support. As
some kernel releases ago, one had to specify i/o ports on kernel cmdline. 2.4.28 kernel works w/o cmdline parameter.

Is this behaviour intended? Will it be fixed in 2.6.10 release?

W/o parameter kernel (2.6) does not recognise the pdc ide controller drives.
dmesg output states: "ideX: Wait for ready failed before probe !"

Quoted 7 lines

As of kernel rc 2.6.10rc1 the kernel even reported ide drive short read and seek errors on drives even not connected to the pdc controller but connected to the onboard controller (->/dev/hda1). In fact /dev/hda1 has no errors (so far).

Any comments?

It's more broken than that here. I get the following errors in 2.6.8 through 2.6.9-ac9 & 2.6.10-rc2 with the old (PDC202XX_OLD) promise driver, when placing the disk/controller under any load (in fact just doing hdparm -t -T /dev/hde).

I get..

hde: dma_intr: status=0xff { Busy }

ide: failed opcode was: unknown
hde: DMA disabled
PDC202XX: Primary channel reset.
PDC202XX: Secondary channel reset.

(a number of times)

ide2: reset timed-out, status=0xff
end_request: I/O error, dev hde, sector 11776 Buffer I/O error on device hde, logical block 1472

(many times)

Cheers,
Al.