Skip to contentSkip to conversation

inittab problem

DISCUSSION Dermot Paikkos 4 participants 5 messages Feb 4, 2005

lore
Share & tools
lore
#0 lore raw

Hi,

SYS: Slackware 9.1 on Dell Dim 2400, Intel Cel

I have go myself into a bit of a fix. I changed the default runlevel from 3 to 4 so I would get a GUI at boot up. However I haven't correctly configured my Xserver and now my system is stalling at boot-up and I can find a way to get access to a shell to edit the inittab.

Does anyone know of a switch/arg I could use that might allow me to boot the system into single users mode? I thought I could boot from my floppy which prompts me for a command to use.

Any ideas,
Dp.

~~
Dermot Paikkos * [email protected]
Network Administrator @ Science Photo Library
Phone: 0207 432 1100 * Fax: 0207 286 8668

#1 lore raw
Quoted 4 lines · Dermot Paikkos

Hi,

SYS: Slackware 9.1 on Dell Dim 2400, Intel Cel

Quoted 8 lines

I have go myself into a bit of a fix. I changed the default runlevel from 3 to 4 so I would get a GUI at boot up. However I haven't correctly configured my Xserver and now my system is stalling at boot-up and I can find a way to get access to a shell to edit the inittab.

Does anyone know of a switch/arg I could use that might allow me to boot the system into single users mode? I thought I could boot from my floppy which prompts me for a command to use.

At the lilo prompt, typ this: init=/bin/sh rw

Signature · 1 line
Yannick Van Osselaer
#2 lore raw
Quoted 10 lines · Yannick Van Osselaer
Quoted 9 lines · Dermot Paikkos

Hi,

SYS: Slackware 9.1 on Dell Dim 2400, Intel Cel

I have go myself into a bit of a fix. I changed the default runlevel from 3 to 4 so I would get a GUI at boot up. However I haven't correctly configured my Xserver and now my system is stalling at boot-up and I can find a way to get access to a shell to edit the inittab.

Quoted 5 lines
Quoted 3 lines

Does anyone know of a switch/arg I could use that might allow me to boot the system into single users mode? I thought I could boot from my floppy which prompts me for a command to use.

At the lilo prompt, typ this: init=/bin/sh rw

You'll have to do a disk sync and run 'umount -a' before turning your computer off via the power switch if you boot this way.

Quoted 8 lines
Signature · 6 lines
Yannick Van Osselaer

-
To unsubscribe from this list: send the line "unsubscribe linux-admin" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Signature · 2 lines
Infinite complexity begets infinite beauty.
Infinite precision begets infinite perfection.
#3 lore raw
In reply to Dermot Paikkos
Quoted 8 lines · Dermot Paikkos

Hi,

SYS: Slackware 9.1 on Dell Dim 2400, Intel Cel

I have go myself into a bit of a fix. I changed the default runlevel from 3 to 4 so I would get a GUI at boot up. However I haven't correctly configured my Xserver and now my system is stalling at boot-up and I can find a way to get access to a shell to edit the inittab.

Does anyone know of a switch/arg I could use that might allow me to boot the system into single users mode? I thought I could boot from my floppy which prompts me for a command to use.

Quoted 7 lines

Any ideas,
Dp.

~~
Dermot Paikkos * [email protected]
Network Administrator @ Science Photo Library
Phone: 0207 432 1100 * Fax: 0207 286 8668

At the lilo boot prompt
boot: Linux
add 'single', thusly
boot: Linux single
or
boot: Linux multi
perhaps even
boot: Linux emergency

HTH, Chuck

#4 lore raw
In reply to Dermot Paikkos
Quoted 9 lines · Dermot Paikkos

Hi,

SYS: Slackware 9.1 on Dell Dim 2400, Intel Cel

I have go myself into a bit of a fix. I changed the default runlevel from 3 to 4 so I would get a GUI at boot up. However I haven't correctly configured my Xserver and now my system is stalling at boot-up and I can find a way to get access to a shell to edit the inittab.

Quoted 7 lines

Does anyone know of a switch/arg I could use that might allow me to boot the system into single users mode? I thought I could boot from my floppy which prompts me for a command to use.

Any ideas,
Dp.

At the boot prompt, append a run level number to the kernel image name.

e.g.

boot: zImage 1

(1 is usually single user mode)

boot: zImage 3

(this gets you back into regular multi user text mode)

Quoted 10 lines

~~
Dermot Paikkos * [email protected]
Network Administrator @ Science Photo Library
Phone: 0207 432 1100 * Fax: 0207 286 8668

-
To unsubscribe from this list: send the line "unsubscribe linux-admin" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Signature · 2 lines
Infinite complexity begets infinite beauty.
Infinite precision begets infinite perfection.