USB 2.0 Mass storage device
Hello,
I have a new MSI Mega Stick 511 USB 2.0 Mass storage device. In my laptop I have USB 2.0 port (Acer TM242), when I connect device, only uhci_hcd driver detect device. Does anyone have some suggestions? Thanks.
Signature · 1 line
Lukáš Hejtmánek
Quoted 5 lines · Lukas Hejtmanek
Hello,
I have a new MSI Mega Stick 511 USB 2.0 Mass storage device. In my laptop I have USB 2.0 port (Acer TM242), when I connect device, only
uhci_hcddriver detect device. Does anyone have some suggestions? Thanks.
Is the ehci-hcd driver loaded? And is your device a high speed one? USB 2.0 support does not mean that it actually goes at high speeds, I have a USB 2.0 "compliant" low speed USB keyboard here :)
thanks,
greg k-h
Quoted 3 lines · Greg KH
Is the ehci-hcd driver loaded? And is your device a high speed one? USB 2.0 support does not mean that it actually goes at high speeds, I have a USB 2.0 "compliant" low speed USB keyboard here :)
Yes, ehci-hcd driver is loaded. (kernel is 2.6.11-rc3-bk4)
This is the device:
http://www.msi.com.tw/program/support/download/dld/spt_dld_detail.php?UID=607&kind=6
Btw, I thought, that ehci-hcd driver handles both usb 2.0 and 1.1. Does it?
Signature · 1 line
Lukáš Hejtmánek
Quoted 11 lines · Lukas Hejtmanek
Quoted 3 lines · Greg KH
Is the ehci-hcd driver loaded? And is your device a high speed one? USB 2.0 support does not mean that it actually goes at high speeds, I have a USB 2.0 "compliant" low speed USB keyboard here :)
Yes, ehci-hcd driver is loaded. (kernel is 2.6.11-rc3-bk4)
This is the device:
http://www.msi.com.tw/program/support/download/dld/spt_dld_detail.php?UID=607&kind=6Btw, I thought, that ehci-hcd driver handles both usb 2.0 and 1.1. Does it?
No, it hands off the usb 1.1 devices to the usb 1 core inside it. This is either uhci or ohci, depending on your controller chip.
Unless you put a USB 2.0 hub in front of a usb 1.1 device, then it gets more complicated, but we'll just ignore that issue for now...
What does /proc/bus/usb/devices show for this device?
thanks,
greg k-h
Quoted 5 lines · Greg KH
Quoted 4 lines
This is the device:
http://www.msi.com.tw/program/support/download/dld/spt_dld_detail.php?UID=607&kind=6Btw, I thought, that ehci-hcd driver handles both usb 2.0 and 1.1. Does it?
Quoted 7 lines
No, it hands off the usb 1.1 devices to the usb 1 core inside it. This is either uhci or ohci, depending on your controller chip.
Unless you put a USB 2.0 hub in front of a usb 1.1 device, then it gets more complicated, but we'll just ignore that issue for now...
What does
/proc/bus/usb/devicesshow for this device?
When connected through uhci-hcd:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1462 ProdID=5511 Rev=10.01 S: Manufacturer=MSI S: Product=MEGA Player 5511 S: SerialNumber=23DE7394D6198090 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Signature · 1 line
Lukáš Hejtmánek
Quoted 9 lines · Lukas Hejtmanek
Quoted 8 lines · Greg KH
Quoted 4 lines
This is the device:
http://www.msi.com.tw/program/support/download/dld/spt_dld_detail.php?UID=607&kind=6Btw, I thought, that ehci-hcd driver handles both usb 2.0 and 1.1. Does it?
No, it hands off the usb 1.1 devices to the usb 1 core inside it. This is either uhci or ohci, depending on your controller chip.
Quoted 7 lines
Quoted 4 lines
Unless you put a USB 2.0 hub in front of a usb 1.1 device, then it gets more complicated, but we'll just ignore that issue for now...
What does
/proc/bus/usb/devicesshow for this device?When connected through uhci-hcd:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
Your device is only reporting that it can go at 12Mbit (full speed, not 480Mbit, which is high speed.)
So it's working properly, but not labeled clearly on the box. We've seen this a lot, you are not alone in your confusion.
I suggest you return it and get a better device.
thanks,
greg k-h
Quoted 5 lines · Greg KH
Quoted 2 lines
When connected through uhci-hcd:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0Your device is only reporting that it can go at 12Mbit (full speed, not 480Mbit, which is high speed.)
Is this independent of used driver?
Signature · 1 line
Lukáš Hejtmánek
Quoted 8 lines · Lukas Hejtmanek
Quoted 5 lines · Greg KH
Quoted 2 lines
When connected through uhci-hcd:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0Your device is only reporting that it can go at 12Mbit (full speed, not 480Mbit, which is high speed.)
Is this independent of used driver?
Yes, this is read from the descriptor of the device.
thanks,
greg k-h
Quoted 20 lines · Greg KH
Quoted 7 lines · Lukas Hejtmanek
Quoted 4 lines · Greg KH
Quoted 4 lines
When connected through uhci-hcd:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0Quoted 7 lines
Quoted 4 lines
Your device is only reporting that it can go at 12Mbit (full speed, not 480Mbit, which is high speed.)
Is this independent of used driver?
Yes, this is read from the descriptor of the device.
Quoted 11 lines
thanks,
greg k-h
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
But why does the usb mass storage give this information to the usb driver? Shouldn't it report that it works with 480Mbit too?
Matthias-Christian Ott
Quoted 2 lines · Matthias-Christian Ott
But why does the usb mass storage give this information to the usb driver? Shouldn't it report that it works with 480Mbit too?
What do you mean? The usb-storage driver doesn't care at all what the speed is. Only the USB core and host controller drivers do.
And if you look at the raw descriptors, which is what is displayed in /proc/bus/usb/devices in human readable form, the device itself tells the computer what speed it supports. The host never tells the device what speed to run at.
Hope this helps,
greg k-h
Quoted 4 lines · Greg KH
And if you look at the raw descriptors, which is what is displayed in
/proc/bus/usb/devicesin human readable form, the device itself tells the computer what speed it supports. The host never tells the device what speed to run at.
I do not think so.
This is another device (Card reader) supporting USB 2.0.
In this case I used only uhci_hcd driver and it reports speed 12.
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05dc ProdID=b018 Rev= 1.28 S: Manufacturer=Lexar Media S: Product=Multi-Card Reader S: SerialNumber=0000246504 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
In this case I used both ehci_hcd and uhci_hcd drivers (ehci detected device) and it reports speed 480.
T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05dc ProdID=b018 Rev= 1.28 S: Manufacturer=Lexar Media S: Product=Multi-Card Reader S: SerialNumber=0000246504 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
So for me it looks like it reports speed according to USB driver or negotiated speed.
Signature · 1 line
Lukáš Hejtmánek
Quoted 29 lines · On 3:38:53 pm 02/24/05 Lukas Hejtmanek <[email protected]> wrote:
This is another device (Card reader) supporting USB 2.0.
In this case I used only
uhci_hcddriver and it reports speed 12.T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05dc ProdID=b018 Rev= 1.28 S: Manufacturer=Lexar Media S: Product=Multi-Card Reader S: SerialNumber=0000246504 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0msIn this case I used both
ehci_hcdanduhci_hcddrivers (ehci detected device) and it reports speed 480.T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05dc ProdID=b018 Rev= 1.28 S: Manufacturer=Lexar Media S: Product=Multi-Card Reader S: SerialNumber=0000246504 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Quoted 2 lines
So for me it looks like it reports speed according to USB driver or negotiated speed.
Same here with a new Seagate external USB 2.0 drive. If plugged into my laptop which does not have USB 2.0 it shows 12 in /dev/bus/usb/devices, however on a machine with USB 2.0 support it changes to 480.
\__ Jason Munro
\__ [email protected]
\__ http://hastymail.sourceforge.net/
Quoted 8 lines · Lukas Hejtmanek
Hello,
I have a new MSI Mega Stick 511 USB 2.0 Mass storage device. In my laptop I have USB 2.0 port (Acer TM242), when I connect device, only
uhci_hcddriver detect device. Does anyone have some suggestions? Thanks.
Hi!
Is hotplug enabled (it should detect it as a scsi generic mass storage)?
Matthias-Christian Ott
Quoted 1 line · Matthias-Christian Ott
Is hotplug enabled (it should detect it as a scsi generic mass storage)?
No, I detect device loading proper modules. With uhci-hcd it works perfectly except the speed. ehci-hcd does not detect it at all.
Signature · 1 line
Lukáš Hejtmánek