I2C busses documentation update

diff -Naur a/Documentation/i2c/busses/i2c-ali15x3 b/Documentation/i2c/busses/i2c-ali15x3
@@ -0,0 +1,112 @@
+Kernel driver i2c-ali15x3
+
+Supported adapters:
+  * Acer Labs, Inc. ALI 1533 and 1543C (south bridge)
+    Datasheet: Now under NDA
+	http://www.ali.com.tw/eng/support/datasheet_request.php
+
+Authors:
+	Frodo Looijaard <[email protected]>,
+	Philip Edelbrock <[email protected]>,
+	Mark D. Studebaker <[email protected]>
+
+Module Parameters
+-----------------
+
+* force_addr: int
+  Initialize the base address of the i2c controller
+
+
+Notes
+-----
+
+The force_addr parameter is useful for boards that don't set the address in
+the BIOS. Does not do a PCI force; the device must still be present in
+lspci. Don't use this unless the driver complains that the base address is
+not set.
+
+Example: 'modprobe i2c-ali15x3 force_addr=0xe800'
+
+SMBus periodically hangs on ASUS P5A motherboards and can only be cleared
+by a power cycle. Cause unknown (see Issues below).
+
+
+Description
+-----------
+
+This is the driver for the SMB Host controller on Acer Labs Inc. (ALI)
+M1541 and M1543C South Bridges.
+
+The M1543C is a South bridge for desktop systems.
+The M1541 is a South bridge for portable systems.
+They are part of the following ALI chipsets:
+
+ * "Aladdin Pro 2" includes the M1621 Slot 1 North bridge with AGP and
+ 		100MHz CPU Front Side bus
+ * "Aladdin V" includes the M1541 Socket 7 North bridge with AGP and 100MHz
+ 		CPU Front Side bus
+   Some Aladdin V motherboards:
+	Asus P5A
+	Atrend ATC-5220
+	BCM/GVC VP1541
+	Biostar M5ALA
+	Gigabyte GA-5AX (** Generally doesn't work because the BIOS doesn't
+                            enable the 7101 device! **)
+	Iwill XA100 Plus
+	Micronics C200
+	Microstar (MSI) MS-5169
+
+  * "Aladdin IV" includes the M1541 Socket 7 North bridge
+   		with host bus up to 83.3 MHz.
+
+For an overview of these chips see http://www.acerlabs.com. At this time the
+full data sheets on the web site are password protected, however if you
+contact the ALI office in San Jose they may give you the password.
+
+The M1533/M1543C devices appear as FOUR separate devices on the PCI bus. An
+output of lspci will show something similar to the following:
+
+  00:02.0 USB Controller: Acer Laboratories Inc. M5237 (rev 03)
+  00:03.0 Bridge: Acer Laboratories Inc. M7101      <= THIS IS THE ONE WE NEED
+  00:07.0 ISA bridge: Acer Laboratories Inc. M1533 (rev c3)
+  00:0f.0 IDE interface: Acer Laboratories Inc. M5229 (rev c1)
+
+** IMPORTANT **
+** If you have a M1533 or M1543C on the board and you get
+** "ali15x3: Error: Can't detect ali15x3!"
+** then run lspci.
+** If you see the 1533 and 5229 devices but NOT the 7101 device,
+** then you must enable ACPI, the PMU, SMB, or something similar
+** in the BIOS.
+** The driver won't work if it can't find the M7101 device.
+
+The SMB controller is part of the M7101 device, which is an ACPI-compliant
+Power Management Unit (PMU).
+
+The whole M7101 device has to be enabled for the SMB to work. You can't
+just enable the SMB alone. The SMB and the ACPI have separate I/O spaces.
+We make sure that the SMB is enabled. We leave the ACPI alone.
+
+Features
+--------
+
+This driver controls the SMB Host only. The SMB Slave
+controller on the M15X3 is not enabled. This driver does not use
+interrupts.
+
+
+Issues
+------
+
+This driver requests the I/O space for only the SMB
+registers. It doesn't use the ACPI region.
+
+On the ASUS P5A motherboard, there are several reports that
+the SMBus will hang and this can only be resolved by
+powering off the computer. It appears to be worse when the board
+gets hot, for example under heavy CPU load, or in the summer.
+There may be electrical problems on this board.
+On the P5A, the W83781D sensor chip is on both the ISA and
+SMBus. Therefore the SMBus hangs can generally be avoided
+by accessing the W83781D on the ISA bus only.
+

42 lines not on this page · raw message

diff -Naur a/Documentation/i2c/busses/i2c-ali1563 b/Documentation/i2c/busses/i2c-ali1563
@@ -0,0 +1,27 @@
+Kernel driver i2c-ali1563
+
+Supported adapters:
+  * Acer Labs, Inc. ALI 1563 (south bridge)
+    Datasheet: Now under NDA
+	http://www.ali.com.tw/eng/support/datasheet_request.php
+
+Author: Patrick Mochel <[email protected]>
+
+Description
+-----------
+
+This is the driver for the SMB Host controller on Acer Labs Inc. (ALI)
+M1563 South Bridge.
+
+For an overview of these chips see http://www.acerlabs.com
+
+The M1563 southbridge is deceptively similar to the M1533, with a few
+notable exceptions. One of those happens to be the fact they upgraded the
+i2c core to be SMBus 2.0 compliant, and happens to be almost identical to
+the i2c controller found in the Intel 801 south bridges.
+
+Features
+--------
+
+This driver controls the SMB Host only. This driver does not use
+interrupts.

diff -Naur a/Documentation/i2c/busses/i2c-amd756 b/Documentation/i2c/busses/i2c-amd756
@@ -0,0 +1,25 @@
+Kernel driver i2c-amd756
+
+Supported adapters:
+  * AMD 756
+  * AMD 766
+  * AMD 768
+  * AMD 8111
+    Datasheets: Publicly available on AMD website
+
+  * nVidia nForce
+    Datasheet: Unavailable
+
+Authors:
+	Frodo Looijaard <[email protected]>,
+	Philip Edelbrock <[email protected]>
+
+Description
+-----------
+
+This driver supports the AMD 756, 766, 768 and 8111 Peripheral Bus
+Controllers, and the nVidia nForce.
+
+Note that for the 8111, there are two SMBus adapters. The SMBus 1.0 adapter
+is supported by this driver, and the SMBus 2.0 adapter is supported by the
+i2c-amd8111 driver.

41 lines not on this page · raw message

80 lines not on this page · raw message

46 lines not on this page · raw message

41 lines not on this page · raw message

diff -Naur a/Documentation/i2c/busses/i2c-parport b/Documentation/i2c/busses/i2c-parport
@@ -1,8 +1,6 @@
-=========
-i2c-parport driver
-=========
+Kernel driver i2c-parport
 
-2004-07-06, Jean Delvare
+Author: Jean Delvare <[email protected]>
 
 This is a unified driver for several i2c-over-parallel-port adapters,
 such as the ones made by Philips, Velleman or ELV. This driver is

@@ -126,14 +124,14 @@
 Similar (but different) drivers
 -------------------------------
 
-This driver is NOT the same as the i2c-pport driver found in the i2c package.
-The i2c-pport driver makes use of modern parallel port features so that
-you don't need additional electronics. It has other restrictions however, and
-was not ported to Linux 2.6 (yet).
+This driver is NOT the same as the i2c-pport driver found in the i2c
+package. The i2c-pport driver makes use of modern parallel port features so
+that you don't need additional electronics. It has other restrictions
+however, and was not ported to Linux 2.6 (yet).
 
 This driver is also NOT the same as the i2c-pcf-epp driver found in the
-lm_sensors package. The i2c-pcf-epp driver doesn't use the parallel port
-as an I2C bus directly. Instead, it uses it to control an external I2C bus
+lm_sensors package. The i2c-pcf-epp driver doesn't use the parallel port as
+an I2C bus directly. Instead, it uses it to control an external I2C bus
 master. That driver was not ported to Linux 2.6 (yet) either.
 
 

diff -Naur a/Documentation/i2c/busses/i2c-parport-light b/Documentation/i2c/busses/i2c-parport-light
@@ -0,0 +1,11 @@
+Kernel driver i2c-parport-light
+
+Author: Jean Delvare <[email protected]>
+
+This driver is a light version of i2c-parport. It doesn't depend
+on the parport driver, and uses direct I/O access instead. This might be
+prefered on embedded systems where wasting memory for the clean but heavy
+parport handling is not an option. The drawback is a reduced portability
+and the impossibility to daisy-chain other parallel port devices.
+
+Please see i2c-parport for documentation.

diff -Naur a/Documentation/i2c/busses/i2c-pca-isa b/Documentation/i2c/busses/i2c-pca-isa
@@ -0,0 +1,23 @@
+Kernel driver i2c-pca-isa
+
+Supported adapters:
+This driver supports ISA boards using the Philips PCA 9564
+Parallel bus to I2C bus controller
+
+Author: Ian Campbell <[email protected]>, Arcom Control Systems
+
+Module Parameters
+-----------------
+
+* base int
+ I/O base address
+* irq int
+ IRQ interrupt
+* clock int
+ Clock rate as described in table 1 of PCA9564 datasheet
+
+Description
+-----------
+
+This driver supports ISA boards using the Philips PCA 9564
+Parallel bus to I2C bus controller

72 lines not on this page · raw message

diff -Naur a/Documentation/i2c/busses/i2c-prosavage b/Documentation/i2c/busses/i2c-prosavage
@@ -0,0 +1,23 @@
+Kernel driver i2c-prosavage
+
+Supported adapters:
+
+	S3/VIA KM266/VT8375 aka ProSavage8
+	S3/VIA KM133/VT8365 aka Savage4
+
+Author: Henk Vergonet <[email protected]>
+
+Description
+-----------
+
+The Savage4 chips contain two I2C interfaces (aka a I2C 'master' or
+'host').
+
+The first interface is used for DDC (Data Display Channel) which is a
+serial channel through the VGA monitor connector to a DDC-compliant
+monitor. This interface is defined by the Video Electronics Standards
+Association (VESA). The standards are available for purchase at
+http://www.vesa.org . The second interface is a general-purpose I2C bus.
+
+Usefull for gaining access to the TV Encoder chips.
+

diff -Naur a/Documentation/i2c/busses/i2c-savage4 b/Documentation/i2c/busses/i2c-savage4
@@ -0,0 +1,26 @@
+Kernel driver i2c-savage4
+
+Supported adapters:
+  * Savage4
+  * Savage2000
+
+Authors:
+	Alexander Wold <[email protected]>,
+	Mark D. Studebaker <[email protected]>
+
+Description
+-----------
+
+The Savage4 chips contain two I2C interfaces (aka a I2C 'master'
+or 'host').
+
+The first interface is used for DDC (Data Display Channel) which is a
+serial channel through the VGA monitor connector to a DDC-compliant
+monitor. This interface is defined by the Video Electronics Standards
+Association (VESA). The standards are available for purchase at
+http://www.vesa.org . The DDC bus is not yet supported because its register
+is not directly memory-mapped.
+
+The second interface is a general-purpose I2C bus. This is the only
+interface supported by the driver at the moment.
+

59 lines not on this page · raw message

49 lines not on this page · raw message

73 lines not on this page · raw message

diff -Naur a/Documentation/i2c/busses/i2c-via b/Documentation/i2c/busses/i2c-via
@@ -0,0 +1,34 @@
+Kernel driver i2c-via
+
+Supported adapters:
+  * VIA Technologies, InC. VT82C586B
+    Datasheet: Publicly available at the VIA website
+
+Author: Ky?sti M?lkki <[email protected]>
+
+Description
+-----------
+
+i2c-via is an i2c bus driver for motherboards with VIA chipset.
+
+The following VIA pci chipsets are supported:
+ - MVP3, VP3, VP2/97, VPX/97
+ - others with South bridge VT82C586B
+
+Your lspci listing must show this :
+
+ Bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
+
+    Problems?
+
+ Q: You have VT82C586B on the motherboard, but not in the listing.
+
+ A: Go to your BIOS setup, section PCI devices or similar.
+    Turn USB support on, and try again.
+
+ Q: No error messages, but still i2c doesn't seem to work.
+
+ A: This can happen. This driver uses the pins VIA recommends in their
+    datasheets, but there are several ways the motherboard manufacturer
+    can actually wire the lines.
+

47 lines not on this page · raw message

62 lines not on this page · raw message

diff -Naur a/Documentation/i2c/busses/scx200_acb b/Documentation/i2c/busses/scx200_acb
@@ -0,0 +1,14 @@
+Kernel driver scx200_acb
+
+Author: Christer Weinigel <[email protected]>
+
+Module Parameters
+-----------------
+
+* base: int
+  Base addresses for the ACCESS.bus controllers
+
+Description
+-----------
+
+Enable the use of the ACCESS.bus controllers of a SCx200 processor.

diff -Naur g/Documentation/i2c/busses/i2c-parport h/Documentation/i2c/busses/i2c-parport
@@ -0,0 +1,156 @@
+=========
+i2c-parport driver
+=========
+
+2004-07-06, Jean Delvare
+
+This is a unified driver for several i2c-over-parallel-port adapters,
+such as the ones made by Philips, Velleman or ELV. This driver is
+meant as a replacement for the older, individual drivers:
+ * i2c-philips-par
+ * i2c-elv
+ * i2c-velleman
+ * video/i2c-parport (NOT the same as this one, dedicated to home brew
+                      teletext adapters)
+
+It currently supports the following devices:
+ * Philips adapter
+ * home brew teletext adapter
+ * Velleman K8000 adapter
+ * ELV adapter
+ * Analog Devices evaluation boards (ADM1025, ADM1030, ADM1031, ADM1032)
+
+These devices use different pinout configurations, so you have to tell
+the driver what you have, using the type module parameter. There is no
+way to autodetect the devices. Support for different pinout configurations
+can be easily added when needed.
+
+
+Building your own adapter
+-------------------------
+
+If you want to build you own i2c-over-parallel-port adapter, here is
+a sample electronics schema (credits go to Sylvain Munaut):
+
+Device                                                      PC
+Side          ___________________Vdd (+)                    Side
+               |    |         |
+              ---  ---       ---
+              | |  | |       | |
+              |R|  |R|       |R|
+              | |  | |       | |
+              ---  ---       ---
+               |    |         |
+               |    |    /|   |
+SCL  ----------x--------o |-----------x-------------------  pin 2
+                    |    \|   |       |
+                    |         |       |
+                    |   |\    |       |
+SDA  ----------x----x---| o---x---------------------------  pin 13
+               |        |/            |
+               |                      |
+               |         /|           |
+               ---------o |----------------x--------------  pin 3
+                         \|           |    |
+                                      |    |
+                                     ---  ---
+                                     | |  | |
+                                     |R|  |R|
+                                     | |  | |
+                                     ---  ---
+                                      |    | 
+                                     ###  ###
+                                     GND  GND
+        
+Remarks:
+ - This is the exact pinout and electronics used on the Analog Devices
+   evaluation boards.
+                   /|
+ - All inverters -o |- must be 74HC05, they must be open collector output.
+                   \|
+ - All resitors are 10k.
+ - Pins 18-25 of the parallel port connected to GND.
+ - Pins 4-9 (D2-D7) could be used as VDD is the driver drives them high.
+   The ADM1032 evaluation board uses D4-D7. Beware that the amount of
+   current you can draw from the parallel port is limited. Also note that
+   all connected lines MUST BE driven at the same state, else you'll short
+   circuit the output buffers! So plugging the I2C adapter after loading
+   the i2c-parport module might be a good safety since data line state
+   prior to init may be unknown. 
+ - This is 5V!
+ - Obviously you cannot read SCL (so it's not really standard-compliant).
+   Pretty easy to add, just copy the SDA part and use another input pin.
+   That would give (ELV compatible pinout):
+
+
+Device                                                      PC
+Side          ______________________________Vdd (+)         Side
+               |    |            |    |
+              ---  ---          ---  ---
+              | |  | |          | |  | |
+              |R|  |R|          |R|  |R|
+              | |  | |          | |  | |
+              ---  ---          ---  ---
+               |    |            |    |
+               |    |      |\    |    |
+SCL  ----------x--------x--| o---x------------------------  pin 15
+                    |   |  |/         | 
+                    |   |             |
+                    |   |   /|        |
+                    |   ---o |-------------x--------------  pin 2
+                    |       \|        |    |
+                    |                 |    |
+                    |                 |    |
+                    |      |\         |    |
+SDA  ---------------x---x--| o--------x-------------------  pin 10
+                        |  |/              |
+                        |                  |
+                        |   /|             |
+                        ---o |------------------x---------  pin 3
+                            \|             |    |
+                                           |    |
+                                          ---  ---
+                                          | |  | |
+                                          |R|  |R|
+                                          | |  | |
+                                          ---  ---
+                                           |    | 
+                                          ###  ###
+                                          GND  GND
+
+
+If possible, you should use the same pinout configuration as existing
+adapters do, so you won't even have to change the code.
+
+
+Similar (but different) drivers
+-------------------------------
+
+This driver is NOT the same as the i2c-pport driver found in the i2c package.
+The i2c-pport driver makes use of modern parallel port features so that
+you don't need additional electronics. It has other restrictions however, and
+was not ported to Linux 2.6 (yet).
+
+This driver is also NOT the same as the i2c-pcf-epp driver found in the
+lm_sensors package. The i2c-pcf-epp driver doesn't use the parallel port
+as an I2C bus directly. Instead, it uses it to control an external I2C bus
+master. That driver was not ported to Linux 2.6 (yet) either.
+
+
+Legacy documentation for Velleman adapter
+-----------------------------------------
+
+Useful links:
+Velleman                http://www.velleman.be/
+Velleman K8000 Howto    http://howto.htlw16.ac.at/k8000-howto.html
+
+The project has lead to new libs for the Velleman K8000 and K8005:
+  LIBK8000 v1.99.1 and LIBK8005 v0.21
+With these libs, you can control the K8000 interface card and the K8005
+stepper motor card with the simple commands which are in the original
+Velleman software, like SetIOchannel, ReadADchannel, SendStepCCWFull and
+many more, using /dev/velleman.
+  http://home.wanadoo.nl/hihihi/libk8000.htm
+  http://home.wanadoo.nl/hihihi/libk8005.htm
+  http://struyve.mine.nu:8080/index.php?block=k8000
+  http://sourceforge.net/projects/libk8005/

156 lines not on this page · raw message

diff -Naur g/Documentation/i2c/busses/i2c-parport h/Documentation/i2c/busses/i2c-parport
@@ -0,0 +1,156 @@
+=========
+i2c-parport driver
+=========
+
+2004-07-06, Jean Delvare
+
+This is a unified driver for several i2c-over-parallel-port adapters,
+such as the ones made by Philips, Velleman or ELV. This driver is
+meant as a replacement for the older, individual drivers:
+ * i2c-philips-par
+ * i2c-elv
+ * i2c-velleman
+ * video/i2c-parport (NOT the same as this one, dedicated to home brew
+                      teletext adapters)
+
+It currently supports the following devices:
+ * Philips adapter
+ * home brew teletext adapter
+ * Velleman K8000 adapter
+ * ELV adapter
+ * Analog Devices evaluation boards (ADM1025, ADM1030, ADM1031, ADM1032)
+
+These devices use different pinout configurations, so you have to tell
+the driver what you have, using the type module parameter. There is no
+way to autodetect the devices. Support for different pinout configurations
+can be easily added when needed.
+
+
+Building your own adapter
+-------------------------
+
+If you want to build you own i2c-over-parallel-port adapter, here is
+a sample electronics schema (credits go to Sylvain Munaut):
+
+Device                                                      PC
+Side          ___________________Vdd (+)                    Side
+               |    |         |
+              ---  ---       ---
+              | |  | |       | |
+              |R|  |R|       |R|
+              | |  | |       | |
+              ---  ---       ---
+               |    |         |
+               |    |    /|   |
+SCL  ----------x--------o |-----------x-------------------  pin 2
+                    |    \|   |       |
+                    |         |       |
+                    |   |\    |       |
+SDA  ----------x----x---| o---x---------------------------  pin 13
+               |        |/            |
+               |                      |
+               |         /|           |
+               ---------o |----------------x--------------  pin 3
+                         \|           |    |
+                                      |    |
+                                     ---  ---
+                                     | |  | |
+                                     |R|  |R|
+                                     | |  | |
+                                     ---  ---
+                                      |    |
+                                     ###  ###
+                                     GND  GND
+
+Remarks:
+ - This is the exact pinout and electronics used on the Analog Devices
+   evaluation boards.
+                   /|
+ - All inverters -o |- must be 74HC05, they must be open collector output.
+                   \|
+ - All resitors are 10k.
+ - Pins 18-25 of the parallel port connected to GND.
+ - Pins 4-9 (D2-D7) could be used as VDD is the driver drives them high.
+   The ADM1032 evaluation board uses D4-D7. Beware that the amount of
+   current you can draw from the parallel port is limited. Also note that
+   all connected lines MUST BE driven at the same state, else you'll short
+   circuit the output buffers! So plugging the I2C adapter after loading
+   the i2c-parport module might be a good safety since data line state
+   prior to init may be unknown.
+ - This is 5V!
+ - Obviously you cannot read SCL (so it's not really standard-compliant).
+   Pretty easy to add, just copy the SDA part and use another input pin.
+   That would give (ELV compatible pinout):
+
+
+Device                                                      PC
+Side          ______________________________Vdd (+)         Side
+               |    |            |    |
+              ---  ---          ---  ---
+              | |  | |          | |  | |
+              |R|  |R|          |R|  |R|
+              | |  | |          | |  | |
+              ---  ---          ---  ---
+               |    |            |    |
+               |    |      |\    |    |
+SCL  ----------x--------x--| o---x------------------------  pin 15
+                    |   |  |/         |
+                    |   |             |
+                    |   |   /|        |
+                    |   ---o |-------------x--------------  pin 2
+                    |       \|        |    |
+                    |                 |    |
+                    |                 |    |
+                    |      |\         |    |
+SDA  ---------------x---x--| o--------x-------------------  pin 10
+                        |  |/              |
+                        |                  |
+                        |   /|             |
+                        ---o |------------------x---------  pin 3
+                            \|             |    |
+                                           |    |
+                                          ---  ---
+                                          | |  | |
+                                          |R|  |R|
+                                          | |  | |
+                                          ---  ---
+                                           |    |
+                                          ###  ###
+                                          GND  GND
+
+
+If possible, you should use the same pinout configuration as existing
+adapters do, so you won't even have to change the code.
+
+
+Similar (but different) drivers
+-------------------------------
+
+This driver is NOT the same as the i2c-pport driver found in the i2c package.
+The i2c-pport driver makes use of modern parallel port features so that
+you don't need additional electronics. It has other restrictions however, and
+was not ported to Linux 2.6 (yet).
+
+This driver is also NOT the same as the i2c-pcf-epp driver found in the
+lm_sensors package. The i2c-pcf-epp driver doesn't use the parallel port
+as an I2C bus directly. Instead, it uses it to control an external I2C bus
+master. That driver was not ported to Linux 2.6 (yet) either.
+
+
+Legacy documentation for Velleman adapter
+-----------------------------------------
+
+Useful links:
+Velleman                http://www.velleman.be/
+Velleman K8000 Howto    http://howto.htlw16.ac.at/k8000-howto.html
+
+The project has lead to new libs for the Velleman K8000 and K8005:
+  LIBK8000 v1.99.1 and LIBK8005 v0.21
+With these libs, you can control the K8000 interface card and the K8005
+stepper motor card with the simple commands which are in the original
+Velleman software, like SetIOchannel, ReadADchannel, SendStepCCWFull and
+many more, using /dev/velleman.
+  http://home.wanadoo.nl/hihihi/libk8000.htm
+  http://home.wanadoo.nl/hihihi/libk8005.htm
+  http://struyve.mine.nu:8080/index.php?block=k8000
+  http://sourceforge.net/projects/libk8005/

156 lines not on this page · raw message