Skip to contentSkip to conversation

HELP: PC104 IO card driver Problem

DISCUSSION nobin matthew 3 participants 3 messages Mar 31, 2005 – Apr 1, 2005

lore
Share & tools
lore
#0 lore raw

Dear Friends,

Can anybody Help me in this Pc104 driver Problem; What is the basics steps in doing read and write on Pc104 cards.

Deatails Given Below:
I am writing a Linux device driver for
Diamond systems
IR104 digital IO card. This is a PC104 bus device(that means it ISA
bus compatible).
The Platform is Arcom Viper borad(with support for PC104), This is a
Xscale, Little endian Platform.

The Specification of PC104 interface given in Viper borad manual is:
0x3C000000-0x3CFFFFFF PC/104 memory space(16MB) 0x30000000-0x300003FF PC/104 IO space(1KB)

Specification given in IR104 manual is:
I made the jumber setting so that, the IO space addresses taken by 8
registers will be 0x300-0x307

The driver should do read and write on this registers(character device
driver).

I took two approaches one is:
i added IO space and 0x300, did inb() and oub().(IO space base address
and 0x300)
otherway i did ioremap on added result, did inb() and oub().

In the second method:
I did same procedures using IO memory space

both methods are giving errors, i think that is related to paging. i think
there is a need for disabling paging in this space.

Please help regarding this. How to solve this.

Nobin Mathew

__________________________________
Do you Yahoo!?
Take Yahoo! Mail with you! Get it on your mobile phone.
http://mobile.yahoo.com/maildemo

#1 lore raw
Quoted 2 lines · nobin matthew

The Platform is Arcom Viper borad(with support for PC104), This is a Xscale, Little endian Platform.

If you contact Arcom technical support on either [email protected] or [email protected] then they will be able to help you with any problems you are having with the VIPER platform.

The answer to your question is that the ISA I/O address space is mapped at address 0xf7000000 on the VIPER so the address you need to use with inb() and outb() is actually 0xf7000300 rather than just 0x300. This is described in the Quickstart manual that ships with the development kit. There is also a document describing this (because it is an FAQ) in the support site http://www.arcom.com/support/faq/Embed_Sys.htm#Linux

Cheers,
Ian.

Signature · 4 lines
Ian Campbell, Senior Design Engineer
                                        Web: http://www.arcom.com
Arcom, Clifton Road,                    Direct: +44 (0)1223 403 465
Cambridge CB1 7EA, United Kingdom       Phone:  +44 (0)1223 411 200
#2 lore raw
In reply to nobin matthew
Quoted 30 lines · nobin matthew

Dear Friends,

Can anybody Help me in this Pc104 driver Problem; What is the basics steps in doing read and write on Pc104 cards.

Deatails Given Below:
I am writing a Linux device driver for
Diamond systems
IR104 digital IO card. This is a PC104 bus device(that means it ISA
bus compatible).
The Platform is Arcom Viper borad(with support for PC104), This is a
Xscale, Little endian Platform.

The Specification of PC104 interface given in Viper borad manual is:
0x3C000000-0x3CFFFFFF PC/104 memory space(16MB) 0x30000000-0x300003FF PC/104 IO space(1KB)

Specification given in IR104 manual is:
I made the jumber setting so that, the IO space addresses taken by 8
registers will be 0x300-0x307

The driver should do read and write on this registers(character device
driver).

Quoted 6 lines

I took two approaches one is:
i added IO space and 0x300, did inb() and oub().(IO space base address
and 0x300)
otherway i did ioremap on added result, did inb() and oub().

/* Remap a not (necessarily) aligned port region */
void *short_remap(unsigned long phys_addr)

{
    /* The code comes mainly from arch/any/mm/ioremap.c */
    unsigned long offset, last_addr, size;

    last_addr = phys_addr + SHORT_NR_PORTS - 1;
    offset = phys_addr & ~PAGE_MASK;
    
    /* Adjust the begin and end to remap a full page */
    phys_addr &= PAGE_MASK;
    size = PAGE_ALIGN(last_addr) - phys_addr;
    return ioremap(phys_addr, size) + offset;
}

/* Unmap a region obtained with short_remap */
void short_unmap(void *virt_add)

{
    iounmap((void *)((unsigned long)virt_add & PAGE_MASK));
}
Quoted 3 lines

In the second method:
I did same procedures using IO memory space

Here Use ioremap to get a base address in the region(0x3C000000-0x3CFFFFFF).
Suppose ISA_BEGIN = 0x3C000000, ISA_END = 0x3CFFFFFF void *base;
base = ioremap(ISA_BEGIN, ISA_END - ISA_BEGIN); base = base - ISA_BEGIN; /* offset */

Use these base address to read and write the IO region.

For more details go to http://www.xml.com/ldd/chapter/book/ch08.html
to get more info.

Quoted 23 lines

both methods are giving errors, i think that is related to paging. i think
there is a need for disabling paging in this space.

Please help regarding this. How to solve this.

Nobin Mathew

__________________________________
Do you Yahoo!?
Take Yahoo! Mail with you! Get it on your mobile phone.
http://mobile.yahoo.com/maildemo

--

Kernelnewbies: Help each other learn about the Linux kernel.
Archive:       http://mail.nl.linux.org/kernelnewbies/
FAQ:           http://kernelnewbies.org/faq/