saa7134: Add OEM version of already supported card
A message that is not in the archive (sent off-list or not yet received): 001501c53ebd$0ca61840$0700000a@pentium4
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): 001901c53f8c$811beef0$0700000a@pentium4
PATCH 1/1 saa7134: Add OEM version of already supported card
Hi Tobias!
Thanks for checking the hardware. It is the same card, the same configuration on the GPx resistors,
just a different subsystem vendor ID stored in its EEPROM.
The below patch is all it should take to have it auto-detected. The driver will say it's a FlyTV, simply because the name strings are stored with the card design data, not the device ID data.
Maintainers: NB, this is my 3rd patch over 2.6.12-rc2 on this file. The patches don't overlap.
Peter
--- linux-2.6.12-rc2/drivers/media/video/saa7134/saa7134-cards.c 2005-04-09 12:01:47.000000000 +0200
+++ video4linux/saa7134-cards.c 2005-04-12 20:56:18.000000000 +0200
@@ -1628,11 +1628,17 @@
},{
.vendor = PCI_VENDOR_ID_PHILIPS,
.device = PCI_DEVICE_ID_PHILIPS_SAA7133,
- .subvendor = 0x5168,
+ .subvendor = 0x5168, /* Animation Technologies (LifeView) */
.subdevice = 0x0214, /* Standard PCI, LR214WF */
.driver_data = SAA7134_BOARD_FLYTVPLATINUM_FM,
},{
.vendor = PCI_VENDOR_ID_PHILIPS,
+ .device = PCI_DEVICE_ID_PHILIPS_SAA7133,
+ .subvendor = 0x1489, /* KYE */
+ .subdevice = 0x0214, /* Genius VideoWonder ProTV */
+ .driver_data = SAA7134_BOARD_FLYTVPLATINUM_FM, /* is an LR214WF actually */
+ },{
+ .vendor = PCI_VENDOR_ID_PHILIPS,
.device = PCI_DEVICE_ID_PHILIPS_SAA7134,
.subvendor = 0x16be,
.subdevice = 0x0003,Quoted 387 lines · Tobias van Dyk
Peter here is the info:
Things I'd like you to check:* There should be a small white sticker on the top side, near the audio/video
connectors, with an 8-digit hex number on. LifeView stick the card's subsystem ID there. That should read 14890214 (or 02141489, can't actually remember the ordering) for yours, further evidence that it's jumped off the same production line. (Does the fine print say "LR214F" anywhere on the card?)
===============>
Yes sticker is 02141489
PCB has LR214 REV D written at bottom righthand side* On the right edge of the card, there is a row of tiny configuration resistors labelled "GP1" through "GP7". I'd like you to write down which ones
are populated and which ones are absent. Gerd and I assume that drivers may detect the finer details of a card's configuration from there, e.g. absence or presence of FM radio feature, so we need to collect how they're configured
for the various versions of each LifeView card design. ==============>
Surface mount R's:
GP1 and GP2 no resistors soldered
GP3 GP4 GP5 GP6 GP7 has soldered resistorsThe tuning offset - I did a clean edit and compile - I do get a signal at -0.15 MHz below the true frequency but it is much weaker (distorted) - the one at -3.95 MHz is stronger - I cannot think why the two cards should be different is this respect. I tried to start the FMTuner "clean" and after TV settings - it does not make a difference. TV norm is PAL-I
Regards
Tobias
----- Original Message -----
From: "Peter Missel" <[email protected]>
To: <[email protected]>
Cc: "Tobias van Dyk" <[email protected]>
Sent: Tuesday, April 12, 2005 5:34 PM
Subject: Re: Genius VideoWonder ProTV SAA7135 and TDA8275 WorkingQuoted 345 lines
Tobias,
on the audio offset, that's odd, it's definitely just .15 MHz for me. What TV
norm are you on? Maybe there's something the tuner code forgets to adjust when switching from TV to radio or somesuch problem.I've had a look around the web, and this card of yours indeed looks EXACTLY
like the FlyTV Platinum FM - even more so from the dmesg capture you gave. It
seems to be like I suspected, same thing with a different subsystem vendor ID
(but even the same subsystem ID0x0214).Things I'd like you to check:
* There should be a small white sticker on the top side, near the audio/video
connectors, with an 8-digit hex number on. LifeView stick the card's subsystem ID there. That should read 14890214 (or 02141489, can't actually remember the ordering) for yours, further evidence that it's jumped off the
same production line. (Does the fine print say "LR214F" anywhere on the card?)* On the right edge of the card, there is a row of tiny configuration resistors labelled "GP1" through "GP7". I'd like you to write down which ones
are populated and which ones are absent. Gerd and I assume that drivers may
detect the finer details of a card's configuration from there, e.g. absence
or presence of FM radio feature, so we need to collect how they're configured
for the various versions of each LifeView card design.Anyone happen to have a FlyTV Platinum w/o FM? Only $38 from newegg, if someone in the US wants to contribute (and end up with a really nice TV card) ...
The above checked and sorted, we can make a simple addition to the saa7134 card database, attributing this alternate subsystem ID with the given implementation of the FlyTV Pl.FM (so we don't have to duplicate code and data all over the place).
regards,
PeterQuoted 295 lines · Tobias van Dyk
Peter I thank you for all your input!
system: Kernel 2.6.11.7 on Mandrake 10.1
4 MHz offset - it is actually -3.95 MHz for example:
101.5 MHz shows as 97.55
94.2 MHz shows as 90.25
I do not know why it is also not -0.15 MHz - I will do a clean snapshot edit again over the weekendGenius/Kye Videowonder Pro TV Product page is here:
http://www.geniusnet.com.tw/product/product-1.asp?pdtno=534lspci -v ================>
02:02.0 Multimedia controller: Philips Semiconductors SAA7133 Audio+video broadcast decoder (rev f0)
Subsystem: KYE Systems Corporation: Unknown device 0214
Flags: bus master, medium devsel, latency 32, IRQ 11 Memory atde000000(32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
lspci -vn ================>
02:02.0 Class 0480: 1131:7133 (rev f0)
Subsystem: 1489:0214
Flags: bus master, medium devsel, latency 32, IRQ 11 Memory atde000000(32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
lsmod | grep saa ============>saa7134 102516 0 video_buf 16676 1 saa7134 v4l2_common 4512 1 saa7134 v4l1_compat 12964 1 saa7134 ir_common 5892 1 saa7134 videodev 7264 1 saa7134 soundcore 7104 2 saa7134,snd i2c_core 17808 6tuner,saa7134,w83627hf,eeprom,i2c_sensor,i2c_isa
dmesg after modprobe ================>
saa7130/34: v4l2 driver version 0.2.12 loaded
saa7130/34: snapshot date 2005-04-04
saa7133[0]: found at 0000:02:02.0, rev: 240, irq: 11, latency: 32, mmio:0xde000000
saa7133[0]: subsystem: 1489:0214, board: LifeView FlyTV Platinum FM [card=54,insmod option]
saa7133[0]: board init: gpio is 21c00
saa7133[0]: dsp access wait timeout [bit=WRR]
saa7133[0]: dsp access wait timeout [bit=WRR]
saa7133[0]: i2c eeprom 00: 89 14 14 02 10 28 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 1-004b: chip found @0x96(saa7133[0])
tuner 1-004b: tuner: type set to tda8290+75
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0========================================================================
=== = DScaler's RegSpy Dumps (State changes for FMRadio/AVInput/AirTV given at end):
SAA7133 Card [0]:Vendor ID: 0x1131 Device ID: 0x7133 Subsystem ID: 0x02141489========================================================================
=== ====== SAA7133 Card - Register Dump:SAA7134_GPIO_GPMODE: 80010000 (10000000 00000001 00000000
00000000)SAA7134_GPIO_GPSTATUS:00031c00(00000000 00000011 00011100
00000000)SAA7134_ANALOG_IN_CTRL1: 81 (10000001) SAA7134_ANALOG_IO_SELECT: 90 (10010000) SAA7134_AUDIO_CLOCK: 90909090 (10010000 10010000 1001000010010000)
SAA7134_VIDEO_PORT_CTRL0: 00000000 (00000000 00000000 00000000
00000000)SAA7134_VIDEO_PORT_CTRL4: 00000000 (00000000 00000000 00000000
00000000)SAA7134_VIDEO_PORT_CTRL8: 00 (00000000) SAA7134_I2S_OUTPUT_SELECT: 00 (00000000) SAA7134_I2S_OUTPUT_FORMAT: 00 (00000000) SAA7134_I2S_OUTPUT_LEVEL: 00 (00000000) SAA7134_I2S_AUDIO_OUTPUT: 00 (00000000) SAA7134_TS_PARALLEL: 00 (00000000) SAA7134_TS_PARALLEL_SERIAL: 00 (00000000) SAA7134_TS_SERIAL0: 00 (00000000) SAA7134_TS_SERIAL1: 00 (00000000) SAA7134_TS_DMA0: 00 (00000000) SAA7134_TS_DMA1: 00 (00000000) SAA7134_TS_DMA2: 00 (00000000) SAA7134_SPECIAL_MODE: 01 (00000001)
0x140: 00000000 (00000000 00000000 00000000
00000000)0x144: 00000000 (00000000 00000000 00000000
00000000)0x148: 00000000 (00000000 00000000 00000000
00000000)0x14C: 00000000 (00000000 00000000 00000000
00000000)0x150: 00000000 (00000000 00000000 00000000
00000000)0x154: 00000000 (00000000 00000000 00000000
00000000)0x158: 00000000 (00000000 00000000 00000000
00000000)0x164: 00000000 (00000000 00000000 00000000
00000000)0x16C: 00000000 (00000000 00000000 00000000
00000000)0x174: 00000000 (00000000 00000000 00000000
00000000)AirTV setting ===============>
SAA7134_GPIO_GPMODE: 80010000 (10000000 00000001 00000000
00000000)SAA7134_GPIO_GPSTATUS:00031c00(00000000 00000011 00011100
00000000)SAA7134_ANALOG_IN_CTRL1: 81 (10000001) SAA7134_ANALOG_IO_SELECT: 90 (10010000) SAA7134_AUDIO_CLOCK: 90909090 (10010000 10010000 1001000010010000)
FMRadio setting =============>SAA7134_GPIO_GPMODE: 80010000 (10000000 00000001 00000000
00000000)SAA7134_GPIO_GPSTATUS:00021c00(00000000 00000010 00011100
00000000)SAA7134_ANALOG_IN_CTRL1: 81 (10000001) SAA7134_ANALOG_IO_SELECT: 90 (10010000) SAA7134_AUDIO_CLOCK: 90909090 (10010000 10010000 1001000010010000)
AVInput setting =============>SAA7134_GPIO_GPMODE: 80010000 (10000000 00000001 00000000
00000000)SAA7134_GPIO_GPSTATUS:00031c00(00000000 00000011 00011100
00000000)SAA7134_ANALOG_IN_CTRL1: 83 (10000011) SAA7134_ANALOG_IO_SELECT: 90 (10010000) SAA7134_AUDIO_CLOCK: 90909090 (10010000 10010000 1001000010010000)
----- Original Message -----
From: "Peter Missel" <[email protected]>
To: <[email protected]>
Sent: Monday, April 11, 2005 11:43 PM
Subject: Re: Genius VideoWonder ProTV SAA7135 and TDA8275 WorkingQuoted 136 lines
Hmmm ... I just got a normal radio unit for comparison, and found that we
aren't actually 4 MHz off - I misidentified the station because there happens
to be one with quite similar a night program exactly there at +4MHz from
my
favorite ...With the station sending on 93.4 MHz actually, I get best tunage on the FlyTV
when the tuner module thinks it tuned to 93.25. A couple more stations revealed:(tuner freq) -> (actual station freq)
87.75 -> 87.9
93.25 -> 93.4
96.55 -> 96.7
99.85 -> 100.0To me it looks more like we're tuning to about .15 MHz higher than the application asks for.
good night - Peter
Quoted 103 lines · Peter Missel
Hi Tobias!
Yes indeed, radio IS working on the FlyTV Platinum FM too - excellent observation on the 4-MHz offset there! "radio" applet indeed displays "mono" but what I have here (a strong local station) clearly does play in stereo.
There seems to be something amiss in the audio handling on saa7135 in general, since in TV modes, I can't switch audio modes (stereo/mono/lang1/lang2) either.
Could you provide us with more detail about that "Genius" card? (With LifeView shifting most of their units feeding badge engineering OEMs, there's some chance it is the same card anyway.)
In the meantime, excuse me while I try to find that 4-MHz offset ...
regards,
PeterQuoted 73 lines · Tobias van Dyk
Genius VideoWonder ProTV with SAA7135 and TDA8275 Tuner is working 99%
(FM Tiuner, TV Tuner and video inputs), with modprobe saa7134 card=54
tuner=54 after the GPIO changes suggested by Peter to the LifeView FlyTV
Platinum. His changes were applied to the 4 April snapshot video4linux-20050403-221421.tar.gzWhat is not working 100% is the FMTuner (tested using GnomeRadio) - it
has a -4 MHz offset in its tuning and all stations is reported as mono
onlyThe working relevant section in
saa7134-cards.cis:[
SAA7134_BOARD_FLYTVPLATINUM_FM] = {
/* LifeView FlyTV Platinum FM (LR214WF) */
/* "Peter Missel */.name = "LifeView FlyTV Platinum FM", .audio_clock = 0x00200000, .tuner_type = TUNER_PHILIPS_TDA8290, .gpiomask = 0x1E000, /* Set GP16, unused 15,14,13 to Output */ .inputs = {{ .name = name_tv, .vmux = 1, .amux = TV, .gpio = 0x10000, /* GP16=1 selects TV input */ .tv = 1, },{/* .name =
name_tv_mono,
.vmux = 1,
.amux = LINE2,
.gpio =0x0000,
.tv = 1,
},{
*/ .name =name_comp1, /* Composite signal on S-Video input */
.vmux = 0,
.amux = LINE2,
// .gpio =0x4000,},{ .name = name_comp2, /* Composite input */ .vmux = 3, .amux = LINE2, // .gpio = 0x4000, },{ .name = name_svideo, /* S-Video signal on S-Video input */ .vmux = 8, .amux = LINE2,// .gpio =
0x4000,
}},
.radio = {
/* I'd certainly be tempted, but seeing how I myself was forced to pretty
much orphan an open-source project in the course of the past year, I'll pass. So I'll be going with my homebrew mix-and-match version for
myself
so that my card works, and as soon as someone picks up maintainership,
I'll submit the current state of affairs properly. Meanwhile, here's my latest changes toward getting everything on the FlyTV Platinum FM going ... GPIO based radio/FM switching. Radio isn't working yet though, and I
haven't put any work at all into getting the remote control going. Current state of affairs: TV and aux inputs work, radio and remote don't.
*/ .name =name_radio,
// .amux = LINE2,
// .gpio =0x2000,
.amux = TV,Quoted 8 lines
.gpio =
0x00000, /* GP16=0 selects FM radio antenna */
},
},
--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-listQuoted 5 lines
--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-listQuoted 5 lines
--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list