Skip to contentSkip to conversation

Routing inside box, is it posible ?

LARTC Rio Martin. 2 participants 3 messages May 26, 2005

lore
Share & tools
lore
#0 lore raw

Dear folks,
I am thinking about routing inside my router box. Is it posible ?

INTERNET --> [eth0] ROUTER1 [eth1] --> [eth0] ROUTER2 [eth1] --> USERS

I want to make it simple just like this:

INTERNET --> [eth0] ROUTER [eth1] --> USERS

Please give me some clues, thanks before ..

Regards,
Rio Martin.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#1 lore raw

For anyone to answer that clearly, we'd need a bit more information.

Firstly, what is connected to router1 and router2? In other words, does the router box you want to use have enough ports (and of the right type) to actually handle all of the connections?

Secondly, can we assume that you have enough access to the box you want to use to be able to install the software and configure it? (This may sound an obvious question, but you'd be amazed how many people don't think of things like that.)

Thirdly, are there any performance constraints? In other words, moving networks from router2 to router1 may impact router1's performance, as it now has to directly process any routing protocols from all subnets router2 listened to, and search a potentially longer and more complex routing table.

Now, if it's a "trivial" network - router1 only connects to two other devices - the outside network and router2, and router2 likewise connects only to two devices - router1 and the inside network, then you can certainly drop one of the two routers. (In fact, in such a simple network, you could probably have a trivial computational device with a static routing table. Dynamic routing isn't needed, if nothing changes. Some switches support basic routing, and a switch would offer much less latency than a router.)

Quoted 11 lines · --- "Rio Martin.

Dear folks,
I am thinking about routing inside my router box. Is it posible ?

INTERNET --> [eth0] ROUTER1 [eth1] --> [eth0]
ROUTER2 [eth1] --> USERS

I want to make it simple just like this:

INTERNET --> [eth0] ROUTER [eth1] --> USERS

Quoted 8 lines

Please give me some clues, thanks before ..

Regards,
Rio Martin.
_______________________________________________
LARTC mailing list
[email protected]

http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

Quoted 1 line

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#2 lore raw
In reply to Rio Martin.

1. From Internet to Router1, Router1 to Router2, and from Router to USERS connected with 100 Mbps LAN UTP-cable.
2. I have full authority and access to all routers we discussed.
3. It seemed i got confused a little bit with the explanation. But the idea is how do i keep the system working like existing now, but with one router only.

Imagine just like you have huge router which is consist of two routers inside it and routing from external network to internal network much flow to those two routers..
I never figured out how this going to work, but i heard from my friend cisco able to do this.

Anyway thanks, hope this is going to be clear for what i asked.

Regards,
Rio Martin.

Quoted 32 lines · Jonathan Day

For anyone to answer that clearly, we'd need a bit more information.

Firstly, what is connected to router1 and router2? In other words, does the router box you want to use have enough ports (and of the right type) to actually handle all of the connections?

Secondly, can we assume that you have enough access to the box you want to use to be able to install the software and configure it? (This may sound an obvious question, but you'd be amazed how many people don't think of things like that.)

Thirdly, are there any performance constraints? In other words, moving networks from router2 to router1 may impact router1's performance, as it now has to directly process any routing protocols from all subnets router2 listened to, and search a potentially longer and more complex routing table.

Now, if it's a "trivial" network - router1 only connects to two other devices - the outside network and router2, and router2 likewise connects only to two devices - router1 and the inside network, then you can certainly drop one of the two routers. (In fact, in such a simple network, you could probably have a trivial computational device with a static routing table. Dynamic routing isn't needed, if nothing changes. Some switches support basic routing, and a switch would offer much less latency than a router.)

Quoted 16 lines
Quoted 15 lines · --- "Rio Martin.

Dear folks,
I am thinking about routing inside my router box. Is it posible ?

INTERNET --> [eth0] ROUTER1 [eth1] --> [eth0]
ROUTER2 [eth1] --> USERS

I want to make it simple just like this:

INTERNET --> [eth0] ROUTER [eth1] --> USERS

Please give me some clues, thanks before ..

Regards,
Rio Martin.

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc