usb/acpi related: irq 11: nobody cared!
Hello,
with 2.6.X we need to give pci=noacpi for some mainboards (gigabyte 7DXE) to get usb working. With 2.4.2X this was no issue with those boards. Any ideas?
Here's an oops without pci=noacpi (2.6.11-ck9 + Win4Lin + bluesmoke patches, the problem is really also existing with a vanilla kernel)
irq 11: nobody cared!
[<c0138bb2>] __report_bad_irq+0x22/0x80 [<c0138c80>] note_interrupt+0x50/0x80 [<c013878b>] __do_IRQ+0x11b/0x120 [<c03a3780>] ip_rcv_finish+0x0/0x2a0 [<c01056da>] do_IRQ+0x1a/0x30 [<c0103f8a>] common_interrupt+0x1a/0x20 [<c03a3780>] ip_rcv_finish+0x0/0x2a0 [<c03993ea>] nf_hook_slow+0x2a/0x100 [<c03a34a5>] ip_rcv+0x435/0x500 [<c03a3780>] ip_rcv_finish+0x0/0x2a0 [<c038fccb>] netif_receive_skb+0x14b/0x210 [<c038fe12>] process_backlog+0x82/0x130 [<c038ff37>] net_rx_action+0x77/0x110 [<c0123dd6>] __do_softirq+0x126/0x160 [<c0123e65>] do_softirq+0x55/0x70 [<c0123fa8>] irq_exit+0x68/0x80 [<c01056df>] do_IRQ+0x1f/0x30 [<c0103f8a>] common_interrupt+0x1a/0x20 [<c0101030>] default_idle+0x0/0x30 [<c0101054>] default_idle+0x24/0x30 [<c01010ed>] cpu_idle+0x4d/0x60 [<c0556881>] start_kernel+0x181/0x1c0
handlers:
[<c035ff70>] (usb_hcd_irq+0x0/0x60)
[<c035ff70>] (usb_hcd_irq+0x0/0x60)
Disabling IRQ #11
CPU0
0: 486512 IO-APIC-edge timer 1: 13 IO-APIC-edge i8042 7: 2 IO-APIC-edge parport0 8: 4 IO-APIC-edge rtc 9: 1 IO-APIC-level acpi 10: 0 IO-APIC-level VIA686A 11: 100000 IO-APIC-level uhci_hcd, uhci_hcd 12: 102 IO-APIC-edge i8042 14: 610 IO-APIC-edge ide0 15: 26 IO-APIC-edge ide1 16: 33105 IO-APIC-level r128@PCI:1:5:0 19: 193715 IO-APIC-level eth0 NMI: 0 LOC: 486129 ERR: 0 MIS: 0
Please tell me, if I can do more about it or if you need more information.
Thanks,
Bernd
Signature · 5 lines
Bernd Schubert PCI / Theoretische Chemie Universität Heidelberg INF 229 69120 Heidelberg
Quoted 2 lines · Bernd Schubert
with 2.6.X we need to give pci=noacpi for some mainboards (gigabyte 7DXE) to get usb working. With 2.4.2X this was no issue with those boards. Any ideas?
Can you try 2.6.12-rc5-mm1 + the following patch, please?
drivers/pci/quirks.c renamed from drivers/pci/quirks.c.orig +3 -11
@@ -499,28 +499,20 @@DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C586_3 , quirk_via_acpi );DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_82C686_4 , quirk_via_acpi ); -static void __devinit quirk_via_irqpic (struct pci_dev *dev) +static void quirk_via_irq (struct pci_dev *dev) {u8 irq, new_irq; -#ifdef CONFIG_X86_IO_APIC -if (nr_ioapics && !skip_ioapic_setup) -return ; -#endif -#ifdef CONFIG_ACPI -if (acpi_irq_model !=ACPI_IRQ_MODEL_PIC ) -return ; -#endif new_irq = dev->irq &0xf ;pci_read_config_byte (dev,PCI_INTERRUPT_LINE , &irq);if (new_irq != irq) { -printk (KERN_INFO "PCI: Via PIC IRQ fixup for %s, from %d to %d\n" , +printk (KERN_INFO "PCI: Via IRQ fixup for %s, from %d to %d\n" ,pci_name (dev), irq, new_irq);udelay (15 );/* unknown if delay really needed */ pci_write_config_byte (dev,PCI_INTERRUPT_LINE , new_irq); } } -DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_ANY_ID , quirk_via_irqpic); +DECLARE_PCI_FIXUP_ENABLE (PCI_VENDOR_ID_VIA ,PCI_ANY_ID , quirk_via_irq);/* * PIIX3 USB: We have to disable USB interrupts that are