Skip to contentSkip to conversation

Parallel Port: Settings PINs on?

DISCUSSION Nico Schottelius 3 participants 4 messages Jun 1, 2005

lore
Share & tools
lore
#0 lore raw

Hello!

Is it possible to select (in userspace) which pins should be enabled or do I have to write a kernel driver for that?

I want to switch a light on/off through my parallel port (attached to a optocoupler, which is attached to an ATX power supply), so I can control the heat in my drying chamber for the eggs of my bearded dragon.

Greetings,

Nico

Signature · 3 lines
Keep it simple & stupid, use what's available.
Please use pgp encryption: 8D0E 27A4 is my id.
http://nico.schotteli.us | http://linux.schottelius.org
#1 lore raw

Hi Nico :)

* Nico Schottelius <[email protected]> dixit:

Quoted 3 lines

Is it possible to select (in userspace) which pins should be enabled or do I have to write a kernel driver for that?

Userspace will do. Take a look at programs like 'parapin', 'k74',
'libieee1284', 'libparportled', or similars. Look in FreshMeat. As far as I know, all them runs in userspace, although you can find some Linux drivers for performing pin control of parallel port.

Raúl Núñez de Arenas Coronado

Signature · 3 lines
Linux Registered User 88736 | http://www.dervishd.net
http://www.pleyades.net & http://www.gotesdelluna.net
It's my PC and I'll cry if I want to...
#2 lore raw
Quoted 9 lines · DervishD

* Nico Schottelius <[email protected]> dixit:

Quoted 3 lines

Is it possible to select (in userspace) which pins should be enabled or do I have to write a kernel driver for that?

Userspace will do. Take a look at programs like 'parapin', 'k74',
'libieee1284', 'libparportled', or similars. Look in FreshMeat. As far as I know, all them runs in userspace, although you can find some Linux drivers for performing pin control of parallel port.

Just for the records: some programs that access the parport use non-portable inb/outb at PCish I/O addresses to control the parport line. Though, I haven't checked the programs mentioned above.

MfG, JBG

Signature · 4 lines
Jan-Benedict Glaw       [email protected]    . +49-172-7608481             _ O _
"Eine Freie Meinung in  einem Freien Kopf    | Gegen Zensur | Gegen Krieg  _ _ O
 fuer einen Freien Staat voll Freier Bürger" | im Internet! |   im Irak!   O O O
ret = do_actions((curr | FREE_SPEECH) & ~(NEW_COPYRIGHT_LAW | DRM | TCPA));
#3 lore raw
In reply to Nico Schottelius
Quoted 3 lines · Nico Schottelius

Is it possible to select (in userspace) which pins should be enabled or do I have to write a kernel driver for that?

There's already a driver available for exactly this purpose: ppdev.

At http://lug-owl.de/~jbglaw/software/steckdose/steckdose.c is a program I wrote for controlling a shift register (serial in, parallel out) with relays attached (to switch on/off computers or to reset them). This should help you for a start. (Basically, open/claim the port and set the bits of the DATA port via an ioctl())

MfG, JBG

Signature · 4 lines
Jan-Benedict Glaw       [email protected]    . +49-172-7608481             _ O _
"Eine Freie Meinung in  einem Freien Kopf    | Gegen Zensur | Gegen Krieg  _ _ O
 fuer einen Freien Staat voll Freier Bürger" | im Internet! |   im Irak!   O O O
ret = do_actions((curr | FREE_SPEECH) & ~(NEW_COPYRIGHT_LAW | DRM | TCPA));