Kernel Panic: VFS cannot open a root device
A message that is not in the archive (sent off-list or not yet received): [email protected]
I already done that things , and I still getting these errors ... I dont no what to do , and I'm getting desesperated...
'>'-- Mensagem Original --
'>'From: Norbert van Nobelen <[email protected]>
'>'To: "GlupFire" <[email protected]>
'>'Subject: Re: Kernel Panic: VFS cannot open a root device '>'Date: Sun, 17 Jul 2005 10:16:37 +0000
'>'
'>'
'>'You should compile in the filesystem (reiserfs?) into the kernel (*
instead
'>'of
'>'M), or put the correct module in initrd (usually done by mkinitrd).
'>'After that run lilo, and it should boot just fine.
'>'
'>'Norbert
'>'
'>'Op zaterdag 16 juli 2005 20:57, schreef u:
'>'> > Hi , i have kernel 2.4.29 at slack 10.1 and when I upgrade my kernel '>'to
'>'> > 2.6.11 I get these erros on booting
'>'> >
'>'> > VFS: Cannot open a root device "301" or unknow block
'>'> > please append a correct "root" boot option
'>'> > KERNEL PANIC : not syncing; VFS; Unable to mount root fs on '>'> > unknown-block (3,1)
'>'> >
'>'> > I have compiled my kernel with my IDE support and also with my file '>'> > system support with built-in option.
'>'> >
'>'> > My LILO.CONF
'>'> > image = /boot/vmlinuz-2.6.11
'>'> > root = /dev/hda1
'>'> > label = 2.6.11
'>'> > initrd = /boot/initrd.gz
'>'> > read-only
'>'> >
'>'> > I googled this problem, and I think is a kind of bug, and i tryed
to
'>'> > patch the kernel with Alan Cox patch 2.6.11-ac7.bzip and I get
these
'>'::
'>'> > bzip2 -dc /usr/src/patch-2.6.11.ac7.bzip | patch -p1 -s '>'> > 1 out of hunk FAILED --saving rejects to file Makefike.rej '>'> >
'>'> > and I cat the file Makefile.rej
'>'> >
'>'> > ***************
'>'> > *** 1,8 ****
'>'> > VERSION = 2
'>'> > PATCHLEVEL = 6
'>'> > SUBLEVEL = 11
'>'> > - EXTRAVERSION =
'>'> > - NAME=Woozy Numbat
'>'> >
'>'> > # *DOCUMENTATION*
'>'> > # To see a list of typical targets execute "make help"
'>'> > --- 1,8 ----
'>'> > VERSION = 2
'>'> > PATCHLEVEL = 6
'>'> > SUBLEVEL = 11
'>'> > + EXTRAVERSION = ac7
'>'> > + NAME=AC
'>'> >
'>'> > # *DOCUMENTATION*
'>'> > # To see a list of typical targets execute "make help"
'>'> >
'>'> > I'm stuck! The patch dont work fine ( I think the patch is not installed '>'> > succesfully on my kernel )
'>'> > I'm booting with my image of kernel 2.4.29..... i'm 5 days tryng
to solve
'>'> > this problem ...
'>'> > any kind of help is wellcome... sorry for my english.
'>'>
'>'> -
'>'> To unsubscribe from this list: send the line "unsubscribe linux-kernel" '>'in
'>'> the body of a message to [email protected]
'>'> More majordomo info at http://vger.kernel.org/majordomo-info.html
'>'> Please read the FAQ at http://www.tux.org/lkml/
Quoted 25 lines · On 7/18/05, [email protected] <[email protected]> wrote:
I already done that things , and I still getting these errors ... I dont no what to do , and I'm getting desesperated...
'>'
'>'You should compile in the filesystem (reiserfs?) into the kernel (*
instead
'>'of
'>'M), or put the correct module in initrd (usually done by mkinitrd).'>'After that run lilo, and it should boot just fine.
'>'
'>'Norbert
'>'
'>'Op zaterdag 16 juli 2005 20:57, schreef u:
'>'> > Hi , i have kernel 2.4.29 at slack 10.1 and when I upgrade my kernel '>'to
'>'> > 2.6.11 I get these erros on booting
'>'> >
'>'> > VFS: Cannot open a root device "301" or unknow block '>'> > please append a correct "root" boot option
'>'> > KERNEL PANIC : not syncing; VFS; Unable to mount root fs on '>'> > unknown-block (3,1)
'>'> >
'>'> > I have compiled my kernel with my IDE support and also with my file '>'> > system support with built-in option.
Quoted 8 lines
'>'> >
'>'> > My LILO.CONF
'>'> > image =/boot/vmlinuz-2.6.11
'>'> > root =/dev/hda1
'>'> > label = 2.6.11
'>'> > initrd =/boot/initrd.gz
'>'> > read-only
'>'> >
I saw this prob when my boot device/partition in the bootloader config was wrong or the filesystem of my root partition is not compiled as a kernel image rather compiled as module, so plz try to solve this prob by selecting your desired filesystem in kernel configuration as Y rather than M ...... I hope this will work
Quoted 3 lines
'>'> > I'm booting with my image of kernel 2.4.29..... i'm 5 days tryng
to solve
'>'> > this problem ...
Upgrading from 2.4.xx kernel series to 2.6.xx series what I found is that the filesystem must be compiled into the kernel image not as a module b/c in 2.4.xx filesystem compiled as module also work ........
And another thing is that I never succedded in booting the 2.6.xx kernel __successfully__ compiled from 2.4.xx series (distribution with default 2.4.xx series kernel like Fedora Core 1 or Redhat Linux 9) and found that my mouse won't work on 2.6.xx series kernel, but the distribution with 2.6.xx kernel series by default works fine .....
Signature · 1 line
Fawad Lateef
Quoted 5 lines · Fawad Lateef
I saw this prob when my boot device/partition in the bootloader config was wrong or the filesystem of my root partition is not compiled as a kernel image rather compiled as module, so plz try to solve this prob by selecting your desired filesystem in kernel configuration as Y rather than M ...... I hope this will work
One further tip. Make your root FS's type the only one that is not a module. Once you have it booting then, if you want, flip other FSes to in kernel.
Ed Tomlinson