24K malta
I'm seeing something strange on a 24K malta and I'm wondering if anyone else has ran into something like it.
This is a 2.6.12 based kernel. I've not had a chance to try the current CVS yet. The last time I checked the current CVS didn't boot as is on a 4Kc malta so I've not been keeping current with CVS.
When I try a simple
strace ls
I either hang or seg fault on a 24Kc or 24Kec processor, but a 4Kc or 4Kec works. If I turn off the cache on the 24K it works as well. Without cache it's unbearably slow of course. This is the same exact build of the kernel and root file system for all boards.
Greg Weeks
Quoted 7 lines · Greg Weeks
I'm seeing something strange on a 24K malta and I'm wondering if anyone else has ran into something like it.
This is a 2.6.12 based kernel. I've not had a chance to try the current CVS yet. The last time I checked the current CVS didn't boot as is on a 4Kc malta so I've not been keeping current with CVS.
Quoted 8 lines
When I try a simple
strace ls
I either hang or seg fault on a 24Kc or 24Kec processor, but a 4Kc or 4Kec works. If I turn off the cache on the 24K it works as well. Without cache it's unbearably slow of course. This is the same exact build of the kernel and root file system for all boards.
I cannot reproduce this problem on 24KEc Malta, sorry.
Ralf
Quoted 10 lines · Ralf Baechle
Quoted 6 lines · Greg Weeks
I'm seeing something strange on a 24K malta and I'm wondering if anyone else has ran into something like it.
This is a 2.6.12 based kernel. I've not had a chance to try the current CVS yet. The last time I checked the current CVS didn't boot as is on a 4Kc malta so I've not been keeping current with CVS.
When I try a simple
Quoted 9 lines
Quoted 5 lines
strace ls
I either hang or seg fault on a 24Kc or 24Kec processor, but a 4Kc or 4Kec works. If I turn off the cache on the 24K it works as well. Without cache it's unbearably slow of course. This is the same exact build of the kernel and root file system for all boards.
I cannot reproduce this problem on 24KEc Malta, sorry.
Good. That means it's something in my old tree.
Thanks.
Greg Weeks
Current CVS fails to build the malta_defconfig with:
scripts/kconfig/mconf arch/mips/Kconfig arch/mips/Kconfig:690: can't open file "arch/mips/tx4938/Kconfig" make[1]: *** [menuconfig] Error 1
make: *** [menuconfig] Error 2
Greg Weeks
Quoted 7 lines · Greg Weeks
Current CVS fails to build the
malta_defconfigwith:
scripts/kconfig/mconfarch/mips/Kconfigarch/mips/Kconfig:690: can't open file "arch/mips/tx4938/Kconfig" make[1]: *** [menuconfig] Error 1
make: *** [menuconfig] Error 2
CVS pilot error. cvs -q update -d -P and don't forget to bitch about it ;)
Ralf
Quoted 7 lines · Ralf Baechle
Quoted 3 lines · Greg Weeks
Current CVS fails to build the
malta_defconfigwith:
Quoted 11 lines
Quoted 6 lines
scripts/kconfig/mconfarch/mips/Kconfigarch/mips/Kconfig:690: can't open file "arch/mips/tx4938/Kconfig" make[1]: *** [menuconfig] Error 1
make: *** [menuconfig] Error 2CVS pilot error. cvs -q update -d -P and don't forget to bitch about it ;)
Would bitching about it do any good? I expect I'd just get told to stick it in my .cvsrc which is what I just did.
Now I get this:
AS arch/mips/kernel/r4k_switch.o
CC arch/mips/kernel/vpe.o
{standard input}: Assembler messages:
{standard input}:1329: Error: unrecognized opcode mftc0 $7,$2,4' {standard input}:1333: Error: unrecognized opcode mftc0 $6,$2,1'
Greg Weeks
Quoted 7 lines · Greg Weeks
Now I get this:
AS
arch/mips/kernel/r4k_switch.o
CCarch/mips/kernel/vpe.o
{standard input}: Assembler messages:
{standard input}:1329: Error: unrecognized opcodemftc0 $7,$2,4' {standard input}:1333: Error: unrecognized opcodemftc0 $6,$2,1'
You have CONFIG_MT enabled but your binutils don't support these new instructions yet. Since you're using 4K and 24K CPUs only ATM I think you should simply disable CONFIG_MT for now.
Ralf
Quoted 14 lines · Ralf Baechle
Quoted 9 lines · Greg Weeks
Now I get this:
AS
arch/mips/kernel/r4k_switch.o
CCarch/mips/kernel/vpe.o
{standard input}: Assembler messages:
{standard input}:1329: Error: unrecognized opcodemftc0 $7,$2,4' {standard input}:1333: Error: unrecognized opcodemftc0 $6,$2,1'
Quoted 6 lines
You have
CONFIG_MTenabled but your binutils don't support these new instructions yet. Since you're using 4K and 24K CPUs only ATM I think you should simply disableCONFIG_MTfor now.
Just turning off the vpe loading support got me past this one. I don't think I have CONFIG_MT set.
[gweeks@tanith linux-8-10-05]$ grep CONFIG_MT .config # CONFIG_MTD is not set
[gweeks@tanith linux-8-10-05]$ cd arch/mips/configs/ [gweeks@tanith configs]$ grep CONFIG_MT malta_defconfig # CONFIG_MTD is not set
[gweeks@tanith configs]$
Greg Weeks
Quoted 8 lines · Greg Weeks
Quoted 6 lines
You have
CONFIG_MTenabled but your binutils don't support these new instructions yet. Since you're using 4K and 24K CPUs only ATM I think you should simply disableCONFIG_MTfor now.Just turning off the vpe loading support got me past this one. I don't think I have
CONFIG_MTset.
Sorry, I meant CONFIG_MIPS_MT.
Ralf
Quoted 6 lines · Greg Weeks
Quoted 4 lines
CVS pilot error. cvs -q update -d -P and don't forget to bitch about it ;)
Would bitching about it do any good? I expect I'd just get told to stick it in my .cvsrc which is what I just did.
Well, cvs's defaults seem to have been choosen following the principle of maximum surprise and you're by far not the first to get traped by that ...
Ralf
Quoted 11 lines · Ralf Baechle
Quoted 7 lines · Greg Weeks
Current CVS fails to build the
malta_defconfigwith:
scripts/kconfig/mconfarch/mips/Kconfigarch/mips/Kconfig:690: can't open file "arch/mips/tx4938/Kconfig" make[1]: *** [menuconfig] Error 1
make: *** [menuconfig] Error 2CVS pilot error. cvs -q update -d -P and don't forget to bitch about it ;)
The CVS authors should have made some sane global defaults. I use this ~/.cvsrc to make it less annoying:
hattusa:~$ cat .cvsrc cvs -qz9 diff -upNR rdiff -uR update -dPR checkout -P
Thiemo
Quoted 10 lines · Ralf Baechle
Quoted 6 lines · Greg Weeks
I'm seeing something strange on a 24K malta and I'm wondering if anyone else has ran into something like it.
This is a 2.6.12 based kernel. I've not had a chance to try the current CVS yet. The last time I checked the current CVS didn't boot as is on a 4Kc malta so I've not been keeping current with CVS.
When I try a simple
Quoted 9 lines
Quoted 5 lines
strace ls
I either hang or seg fault on a 24Kc or 24Kec processor, but a 4Kc or 4Kec works. If I turn off the cache on the 24K it works as well. Without cache it's unbearably slow of course. This is the same exact build of the kernel and root file system for all boards.
I cannot reproduce this problem on 24KEc Malta, sorry.
What patch are you using to get current CVS to boot on a malta? I've been disabling prefetch in memcpy, but if you're doing something else I want to try that. About 1 out of 3 "strace ls" either hangs or seg faults on me still.
Greg Weeks
Quoted 7 lines · Greg Weeks
Quoted 3 lines
I cannot reproduce this problem on 24KEc Malta, sorry.
What patch are you using to get current CVS to boot on a malta? I've been disabling prefetch in memcpy, but if you're doing something else I want to try that. About 1 out of 3 "strace ls" either hangs or seg faults on me still.
I've disabled prefetching entirely in arch/mips/Kconfig and I'm using a 24Kc, not a 24KEc, stock gcc 3.4 & binutils 2.16 and it's running quite nicely for me.
Ralf
Quoted 9 lines · Greg Weeks
I'm seeing something strange on a 24K malta and I'm wondering if anyone else has ran into something like it.
This is a 2.6.12 based kernel. I've not had a chance to try the current CVS yet. The last time I checked the current CVS didn't boot as is on a 4Kc malta so I've not been keeping current with CVS.
When I try a simple
strace ls
I either hang or seg fault on a 24Kc or 24Kec processor, but a 4Kc or 4Kec works. If I turn off the cache on the 24K it works as well. Without cache it's unbearably slow of course. This is the same exact build of the kernel and root file system for all boards.
The memcpy prefetch bug is still there for malta, so I had to build another kernel. This is with a CVS sync from this morning.
The first strace ls works now, but the second time I do it it hangs. Kill -9 frees it up and the board isn't hanging.
Greg Weeks