Skip to contentSkip to conversation

debug a high load average

DISCUSSION Rajesh 3 participants 4 messages Aug 23, 2005 – Aug 24, 2005

lore
Share & tools
lore

Rajesh

author
#0 lore raw

Hi All:

I have a case occasionally when I copy data from a usb storage (ipod) to my hard drive the load average goes up from 0.4 to about 15.0, and the system becomes very unusable till I kill the cp command. I have checked the CPU usage, bytes read from usb device, byte written to hard drive etc, and all these values are low like CPU usage is at a maximum of 30%, disk read bytes is at an average of 1.5 MiB/s, disk write bytes is at 1.5 MiB/s, number of processes is at 110, etc, during this high load.

So my question is what else determines the high load average that in turn is resulting in the unresponsiveness of the system? What else should I be looking for to debug the problem?

Thanks a lot,
Rajesh

#1 lore raw
Quoted 7 lines · Rajesh

I have a case occasionally when I copy data from a usb storage (ipod) to my hard drive the load average goes up from 0.4 to about 15.0, and the system becomes very unusable till I kill the cp command. I have checked the CPU usage, bytes read from usb device, byte written to hard drive etc, and all these values are low like CPU usage is at a maximum of 30%, disk read bytes is at an average of 1.5 MiB/s, disk write bytes is at 1.5 MiB/s, number of processes is at 110, etc, during this high load.

1.5 MB/s suggests you're using an IDE drive in PIO mode. Switch to DMA mode (hdparm -d 1 /dev/hda) and see if it gets any better.

Erik

Signature · 2 lines
+-- Erik Mouw -- www.harddisk-recovery.com -- +31 70 370 12 90 --
| Lab address: Delftechpark 26, 2628 XH, Delft, The Netherlands
author
#2 lore raw
Quoted 12 lines · Erik Mouw
Quoted 3 lines · Rajesh

I have a case occasionally when I copy data from a usb storage (ipod) to my hard drive the load average goes up from 0.4 to about 15.0, and the system becomes very unusable till I kill the cp command. I have checked the CPU usage, bytes read from usb device, byte written to hard drive etc, and all these values are low like CPU usage is at a maximum of 30%, disk read bytes is at an average of 1.5 MiB/s, disk write bytes is at 1.5 MiB/s, number of processes is at 110, etc, during this high load.

1.5 MB/s suggests you're using an IDE drive in PIO mode. Switch to DMA mode (hdparm -d 1 /dev/hda) and see if it gets any better.

It seems to have helped a little. Now the rate at which load average goes up has decreased ( I can copy up to about 700-800 MiB compared to a high of 200MiB earlier), but it is still going up to 15 gradually at which point I am still killing the cp process to make the system usable.

I know I am not giving much information. But if I know what factors cause the loadavg to keep on going up I will gladly provide it.

I am running 2.6.12 kernel on a laptop. I have an ipod attached to my USB 1.1 as a drive on which I am saving and retreiving large files(2-4GiB files). The transfer speed is slow, but I am fine with it, as long as the load average stays within bounds so that the machine is usable. (If I dual boot to windows and do the same operation, I am able to get the files copied over in a few minutes.). Can vfat be a factor?

Thanks
Rajesh

Quoted 4 lines

Erik

#3 lore raw

On Wednesday 24 August 2005 06:40, you wrote:
[...]

Quoted 3 lines

I am running 2.6.12 kernel on a laptop. I have an ipod attached to my USB 1.1 as a drive on which I am saving and retreiving large files(2-4GiB files).

[...]

Check if you are not using low performance usb driver (CONFIG_BLK_DEV_UB). If I remember correctly it uses /dev/ub* devices.

Signature · 1 line
Mariusz Zielinski