Skip to contentSkip to conversation

dcdbas: add Dell Systems Management Base Driver with sysfs support

PATCH In review Doug Warzecha 2 participants 3 messages Aug 25, 2005 Documentation

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 dcdbas: add Dell Systems Management Base Driver with sysfs support

This patch adds the Dell Systems Management Base Driver with sysfs support.

This driver has been tested with Dell OpenManage.

---

Documentation/dcdbas.txt +87 -0
diff -uprN linux-2.6.13-rc6.orig/Documentation/dcdbas.txt linux-2.6.13-rc6/Documentation/dcdbas.txt
@@ -0,0 +1,87 @@
+Overview
+
+The Dell Systems Management Base Driver provides a sysfs interface for
+systems management software such as Dell OpenManage to perform system
+management interrupts and host control actions (system power cycle or
+power off after OS shutdown) on certain Dell systems.
+
+Dell OpenManage requires this driver on the following Dell PowerEdge systems:
+300, 1300, 1400, 400SC, 500SC, 1500SC, 1550, 600SC, 1600SC, 650, 1655MC,
+700, and 750.  Other Dell software such as the open source Libsmbios library
+is expected to make use of this driver, and it may include the use of this
+driver on other Dell systems.
+
+
+System Management Interrupt
+
+On some Dell systems, systems management software must access certain
+management information via a system management interrupt (SMI).  The SMI data
+buffer must reside in 32-bit address space, and the physical address of the
+buffer is required for the SMI.  The driver maintains the memory required for
+the SMI and provides a way for the application to generate the SMI.
+The driver creates the following sysfs entries for systems management
+software to perform these system management interrupts:
+
+/sys/devices/platform/dcdbas/smi_data
+/sys/devices/platform/dcdbas/smi_data_buf_phys_addr
+/sys/devices/platform/dcdbas/smi_data_buf_size
+/sys/devices/platform/dcdbas/smi_request
+
+Systems management software must perform the following steps to execute
+a SMI using this driver:
+
+1) Lock smi_data.
+2) Write system management command to smi_data.
+3) Write "1" to smi_request to generate a calling interface SMI or
+   "2" to generate a raw SMI.
+4) Read system management command response from smi_data.
+5) Unlock smi_data.
+
+
+Host Control Action
+
+Dell OpenManage supports a host control feature that allows the administrator
+to perform a power cycle or power off of the system after the OS has finished
+shutting down.  On some Dell systems, this host control feature requires that
+a driver perform a SMI after the OS has finished shutting down.
+
+The driver creates the following sysfs entries for systems management software
+to schedule the driver to perform a power cycle or power off host control
+action after the system has finished shutting down:
+
+/sys/devices/platform/dcdbas/host_control_action
+/sys/devices/platform/dcdbas/host_control_smi_type
+/sys/devices/platform/dcdbas/host_control_on_shutdown
+
+Dell OpenManage performs the following steps to execute a power cycle or
+power off host control action using this driver:
+
+1) Write host control action to be performed to host_control_action.
+2) Write type of SMI that driver needs to perform to host_control_smi_type.
+3) Write "1" to host_control_on_shutdown to enable host control action.
+4) Initiate OS shutdown.
+   (Driver will perform host control SMI when it is notified that the OS
+   has finished shutting down.)
+
+
+Host Control SMI Type
+
+The following table shows the value to write to host_control_smi_type to
+perform a power cycle or power off host control action:
+
+PowerEdge System    Host Control SMI Type
+----------------    ---------------------
+      300             HC_SMITYPE_TYPE1
+     1300             HC_SMITYPE_TYPE1
+     1400             HC_SMITYPE_TYPE2
+      500SC           HC_SMITYPE_TYPE2
+     1500SC           HC_SMITYPE_TYPE2
+     1550             HC_SMITYPE_TYPE2
+      600SC           HC_SMITYPE_TYPE2
+     1600SC           HC_SMITYPE_TYPE2
+      650             HC_SMITYPE_TYPE2
+     1655MC           HC_SMITYPE_TYPE2
+      700             HC_SMITYPE_TYPE3
+      750             HC_SMITYPE_TYPE3
+
+
drivers/firmware/dcdbas.c +593 -0

593 lines not on this page · raw message

drivers/firmware/dcdbas.h +107 -0

107 lines not on this page · raw message

drivers/firmware/Kconfig +17 -0
diff -uprN linux-2.6.13-rc6.orig/drivers/firmware/Kconfig linux-2.6.13-rc6/drivers/firmware/Kconfig
@@ -58,4 +58,21 @@ config EFI_PCDP
 
 	  See <http://www.dig64.org/specifications/DIG64_HCDPv20_042804.pdf>
 
+config DCDBAS
+	tristate "Dell Systems Management Base Driver"
+	depends on X86 || X86_64
+	default m
+	help
+	  The Dell Systems Management Base Driver provides a sysfs interface
+	  for systems management software to perform System Management
+	  Interrupts (SMIs) and Host Control Actions (system power cycle or
+	  power off after OS shutdown) on certain Dell systems.
+
+	  See <file:Documentation/dcdbas.txt> for more details on the driver
+	  and the Dell systems on which Dell systems management software makes
+	  use of this driver.
+
+	  Say Y or M here to enable the driver for use by Dell systems
+	  management software such as Dell OpenManage.
+
 endmenu
drivers/firmware/Makefile +1 -0
diff -uprN linux-2.6.13-rc6.orig/drivers/firmware/Makefile linux-2.6.13-rc6/drivers/firmware/Makefile
@@ -4,3 +4,4 @@
 obj-$(CONFIG_EDD)             	+= edd.o
 obj-$(CONFIG_EFI_VARS)		+= efivars.o
 obj-$(CONFIG_EFI_PCDP)		+= pcdp.o
+obj-$(CONFIG_DCDBAS)		+= dcdbas.o
MAINTAINERS +5 -0
diff -uprN linux-2.6.13-rc6.orig/MAINTAINERS linux-2.6.13-rc6/MAINTAINERS
@@ -696,6 +696,11 @@ M:	[email protected]
 W:	http://www.debian.org/~dz/i8k/
 S:	Maintained
 
+DELL SYSTEMS MANAGEMENT BASE DRIVER (dcdbas)
+P:	Doug Warzecha
+M:	[email protected]
+S:	Maintained
+
 DEVICE-MAPPER
 P:	Alasdair Kergon
 L:	[email protected]
#1 lore raw

On Wed, Aug 24, 2005 at 09:00:21PM -0500, Doug Warzecha wrote:

[...]

Documentation/dcdbas.txt line 12

Quoted 5 lines
Documentation/dcdbas.txt +5 -0
+Dell OpenManage requires this driver on the following Dell PowerEdge systems:
+300, 1300, 1400, 400SC, 500SC, 1500SC, 1550, 600SC, 1600SC, 650, 1655MC,
+700, and 750.  Other Dell software such as the open source Libsmbios library
+is expected to make use of this driver, and it may include the use of this
+driver on other Dell systems.

I'd like to see a URL/pointer somewhere about here in the docs for the location of libsmbios if nobody objects.

#2 lore raw
Quoted 4 lines · Chris Wedgwood

On Wed, Aug 24, 2005 at 09:00:21PM -0500, Doug Warzecha wrote:

[...]

Quoted 8 lines

Documentation/dcdbas.txt line 12

Quoted 5 lines
Documentation/dcdbas.txt +5 -0
+Dell OpenManage requires this driver on the following Dell PowerEdge systems:
+300, 1300, 1400, 400SC, 500SC, 1500SC, 1550, 600SC, 1600SC, 650, 1655MC,
+700, and 750.  Other Dell software such as the open source Libsmbios library
+is expected to make use of this driver, and it may include the use of this
+driver on other Dell systems.

I'd like to see a URL/pointer somewhere about here in the docs for the location of libsmbios if nobody objects.

No objections. I'll add it.

Doug