Skip to contentSkip to conversation

USB EHCI Problem with Low Speed Devices on kernel 2.6.11+

DISCUSSION Pete Zaitcev 3 participants 4 messages Aug 27, 2005 – Aug 29, 2005 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw

On Sat, 27 Aug 2005 15:43:11 +0200, Dominik Wezel <[email protected]> wrote:

Forwarding to linux-usb-devel with comments.

Quoted 85 lines

Kernel
======
- 2.6.8, 2.6.11.10 and 2.6.12.4, all show same problem

Problem
=======
When turning on the laptop and during POST and GrUB loading, all ports on the hub are enabled. During the USB initialization phase, when the hub is detected, shortly all ports become disabled, then turn on again (uhci_hcd detects the lo-speed ports). Upon initialization of ehci_hcd however, the ports are disconnected again (for good):

---8<----

Aug 27 14:29:50 solaris kernel: ehci_hcd 0000:00:1d.7: USB 2.0 
initialized, EHCI 1.00, driver 10 Dec 2004
Aug 27 14:29:50 solaris kernel: hub 4-0:1.0: USB hub found
Aug 27 14:29:50 solaris kernel: hub 4-0:1.0: 6 ports detected
Aug 27 14:29:50 solaris kernel: usb 2-1: USB disconnect, address 2
Aug 27 14:29:50 solaris kernel: usb 2-1.5: USB disconnect, address 3
Aug 27 14:29:50 solaris kernel: usb 2-1.6: USB disconnect, address 4

---8<----

Addresses 2, 3 and 4 are a keyboard, mouse and palm sync cable respectively.

and afterwards the log becomes cluttered with:

---8<----

Aug 27 14:30:31 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 79
Aug 27 14:30:31 solaris kernel: usb 4-3: device not accepting address 
79, error -71
Aug 27 14:30:32 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 81
Aug 27 14:30:32 solaris kernel: usb 4-3: device not accepting address 
81, error -71
Aug 27 14:30:33 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 86
Aug 27 14:30:34 solaris kernel: usb 4-3: device not accepting address 
86, error -71
Aug 27 14:30:34 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 89
Aug 27 14:30:35 solaris kernel: usb 4-3: device not accepting address 
89, error -71
Aug 27 14:30:35 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 90
Aug 27 14:30:35 solaris kernel: usb 4-3: device not accepting address 

90, error -71
---8<----

first address to be assigned was 30 in all logs, but the number raises mostly in increments of 2 till about 120, then restarts with 12.

Interestlingly, the keyboard and mouse have been detected immediately before the intialization of ehcihcd:

---8<---

Aug 27 14:29:50 solaris kernel: uhci_hcd 0000:00:1d.2: Intel Corp. 
82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
Aug 27 14:29:50 solaris kernel: PCI: Setting latency timer of device 
0000:00:1d.2 to 64
Aug 27 14:29:50 solaris kernel: uhci_hcd 0000:00:1d.2: irq 11, io base 
0x1840
Aug 27 14:29:50 solaris kernel: uhci_hcd 0000:00:1d.2: new USB bus 
registered, assigned bus number 3
Aug 27 14:29:50 solaris kernel: hub 3-0:1.0: USB hub found
Aug 27 14:29:50 solaris kernel: hub 3-0:1.0: 2 ports detected
/* These are the 2 ports on the laptop */
Aug 27 14:29:50 solaris kernel: usb 2-1: new full speed USB device using 
uhci_hcd and address 2
Aug 27 14:29:50 solaris kernel: hub 2-1:1.0: USB hub found
Aug 27 14:29:50 solaris kernel: hub 2-1:1.0: 7 ports detected
/* These are the 7 ports of the external hub */
Aug 27 14:29:50 solaris kernel: usb 2-1.5: new low speed USB device 
using uhci_hcd and address 3
Aug 27 14:29:50 solaris kernel: usb 2-1.6: new low speed USB device 
using uhci_hcd and address 4
Aug 27 14:29:50 solaris kernel: usbcore: registered new driver hiddev
Aug 27 14:29:50 solaris kernel: input: USB HID v1.10 Mouse [Logitech 
Trackball] on usb-0000:00:1d.1-1.5
Aug 27 14:29:50 solaris kernel: input: USB HID v1.10 Keyboard [CHICONY 
USB Keyboard] on usb-0000:00:1d.1-1.6
Aug 27 14:29:50 solaris kernel: input,hiddev96: USB HID v1.10 Device 
[CHICONY USB Keyboard] on usb-0000:00:1d.1-1.6
Aug 27 14:29:50 solaris kernel: usbcore: registered new driver usbhid
Aug 27 14:29:50 solaris kernel: drivers/usb/input/hid-core.c: v2.0:USB 
Quoted 7 lines

HID core driver
---8<---

which means the ehci_hcd has afterwards superseded uhci_hcd.

Even more interestingly: in about 5% of the boot cases, ehci_hcd manages to detect the ports correctly (or at least doesn't interfere with uhci).

Curious.

Quoted 4 lines

Measures taken
==============
I've found an article suggesting to
echo Y > /sys/module/usbcore/parameters/old_scheme_first

Very funny.

Quoted 5 lines

---
I've also found articles suggesting to throw away the hub and get another one, which of course I can't take plain seriously, because now I know the problem of this hub, and I'm not going to change it for a hub whose problem I even don't know yet... =;)

Borrow one for testing.

Also, plug Palm directly into computer. Surely it has more than one USB connector.

Quoted 6 lines

Measures not taken
==================
I didn't test the hub on Microsoft Windows, because I assume that wouldn't add to the solution space, since the problem is clearly located in the uhci_hcd vs. ehci_hcd domain of the linux kernel, as the hub is fully functional (within the lo speed scope) when used with only uhci.

Actually, I suspected that this may be a poorly working Transaction Tranlating (TT) hub. Which then may work on certain versions of Windows.

-- Pete

#2 lore raw
Quoted 124 lines · Pete Zaitcev

On Sat, 27 Aug 2005 15:43:11 +0200, Dominik Wezel <[email protected]> wrote:

Forwarding to linux-usb-devel with comments.

Quoted 85 lines

Kernel
======
- 2.6.8, 2.6.11.10 and 2.6.12.4, all show same problem

Problem
=======
When turning on the laptop and during POST and GrUB loading, all ports on the hub are enabled. During the USB initialization phase, when the hub is detected, shortly all ports become disabled, then turn on again (uhci_hcd detects the lo-speed ports). Upon initialization of ehci_hcd however, the ports are disconnected again (for good):

---8<----

Aug 27 14:29:50 solaris kernel: ehci_hcd 0000:00:1d.7: USB 2.0 
initialized, EHCI 1.00, driver 10 Dec 2004
Aug 27 14:29:50 solaris kernel: hub 4-0:1.0: USB hub found
Aug 27 14:29:50 solaris kernel: hub 4-0:1.0: 6 ports detected
Aug 27 14:29:50 solaris kernel: usb 2-1: USB disconnect, address 2
Aug 27 14:29:50 solaris kernel: usb 2-1.5: USB disconnect, address 3
Aug 27 14:29:50 solaris kernel: usb 2-1.6: USB disconnect, address 4

---8<----

Addresses 2, 3 and 4 are a keyboard, mouse and palm sync cable respectively.

and afterwards the log becomes cluttered with:

---8<----

Aug 27 14:30:31 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 79
Aug 27 14:30:31 solaris kernel: usb 4-3: device not accepting address 
79, error -71
Aug 27 14:30:32 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 81
Aug 27 14:30:32 solaris kernel: usb 4-3: device not accepting address 
81, error -71
Aug 27 14:30:33 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 86
Aug 27 14:30:34 solaris kernel: usb 4-3: device not accepting address 
86, error -71
Aug 27 14:30:34 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 89
Aug 27 14:30:35 solaris kernel: usb 4-3: device not accepting address 
89, error -71
Aug 27 14:30:35 solaris kernel: usb 4-3: new high speed USB device using 
ehci_hcd and address 90
Aug 27 14:30:35 solaris kernel: usb 4-3: device not accepting address 

90, error -71
---8<----

first address to be assigned was 30 in all logs, but the number raises mostly in increments of 2 till about 120, then restarts with 12.

Interestlingly, the keyboard and mouse have been detected immediately before the intialization of ehcihcd:

---8<---

Aug 27 14:29:50 solaris kernel: uhci_hcd 0000:00:1d.2: Intel Corp. 
82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
Aug 27 14:29:50 solaris kernel: PCI: Setting latency timer of device 
0000:00:1d.2 to 64
Aug 27 14:29:50 solaris kernel: uhci_hcd 0000:00:1d.2: irq 11, io base 
0x1840
Aug 27 14:29:50 solaris kernel: uhci_hcd 0000:00:1d.2: new USB bus 
registered, assigned bus number 3
Aug 27 14:29:50 solaris kernel: hub 3-0:1.0: USB hub found
Aug 27 14:29:50 solaris kernel: hub 3-0:1.0: 2 ports detected
/* These are the 2 ports on the laptop */
Aug 27 14:29:50 solaris kernel: usb 2-1: new full speed USB device using 
uhci_hcd and address 2
Aug 27 14:29:50 solaris kernel: hub 2-1:1.0: USB hub found
Aug 27 14:29:50 solaris kernel: hub 2-1:1.0: 7 ports detected
/* These are the 7 ports of the external hub */
Aug 27 14:29:50 solaris kernel: usb 2-1.5: new low speed USB device 
using uhci_hcd and address 3
Aug 27 14:29:50 solaris kernel: usb 2-1.6: new low speed USB device 
using uhci_hcd and address 4
Aug 27 14:29:50 solaris kernel: usbcore: registered new driver hiddev
Aug 27 14:29:50 solaris kernel: input: USB HID v1.10 Mouse [Logitech 
Trackball] on usb-0000:00:1d.1-1.5
Aug 27 14:29:50 solaris kernel: input: USB HID v1.10 Keyboard [CHICONY 
USB Keyboard] on usb-0000:00:1d.1-1.6
Aug 27 14:29:50 solaris kernel: input,hiddev96: USB HID v1.10 Device 
[CHICONY USB Keyboard] on usb-0000:00:1d.1-1.6
Aug 27 14:29:50 solaris kernel: usbcore: registered new driver usbhid
Aug 27 14:29:50 solaris kernel: drivers/usb/input/hid-core.c: v2.0:USB 
Quoted 7 lines

HID core driver
---8<---

which means the ehci_hcd has afterwards superseded uhci_hcd.

Even more interestingly: in about 5% of the boot cases, ehci_hcd manages to detect the ports correctly (or at least doesn't interfere with uhci).

Curious.

Quoted 4 lines

Measures taken
==============
I've found an article suggesting to
echo Y > /sys/module/usbcore/parameters/old_scheme_first

Very funny.

Quoted 5 lines

---
I've also found articles suggesting to throw away the hub and get another one, which of course I can't take plain seriously, because now I know the problem of this hub, and I'm not going to change it for a hub whose problem I even don't know yet... =;)

Borrow one for testing.

Also, plug Palm directly into computer. Surely it has more than one USB connector.

Quoted 6 lines

Measures not taken
==================
I didn't test the hub on Microsoft Windows, because I assume that wouldn't add to the solution space, since the problem is clearly located in the uhci_hcd vs. ehci_hcd domain of the linux kernel, as the hub is fully functional (within the lo speed scope) when used with only uhci.

Quoted 5 lines

Actually, I suspected that this may be a poorly working Transaction Tranlating (TT) hub. Which then may work on certain versions of Windows.

-- Pete

It looks to me more like a timing problem with initialization of the external high-speed hub. Try this patch:

http://marc.theaimsgroup.com/?l=linux-usb-devel&m=112439094723976&w=2

Alan Stern

#3 lore raw
Quoted 6 lines · Alan Stern
Quoted 3 lines · Pete Zaitcev
Quoted 3 lines

Kernel
======
- 2.6.8, 2.6.11.10 and 2.6.12.4, all show same problem

Quoted 8 lines
Quoted 3 lines

Actually, I suspected that this may be a poorly working Transaction Tranlating (TT) hub. Which then may work on certain versions of Windows.

It looks to me more like a timing problem with initialization of the external high-speed hub. Try this patch:

http://marc.theaimsgroup.com/?l=linux-usb-devel&m=112439094723976&w=2

Yes, Dominik, please do. The TT was a poor guess, because IIRC 2.6.8 did not have the support for TT, so it could not get it wrong.

But testing this hub elsewhere _and_ replacing it with a borrowed hub would be a good idea, IMHO.

-- Pete

#4 lore raw
In reply to Alan Stern

Alan

Quoted 4 lines

It looks to me more like a timing problem with initialization of the external high-speed hub. Try this patch:

http://marc.theaimsgroup.com/?l=linux-usb-devel&m=112439094723976&w=2

Thank you very much: the patch seems indeed to fix the problem. However, I didn't boot more than twice with the new kernel now, and in a setup with unsystematic behaviour, such a small series of successes may mean nothing.

You'll hear from me though in either case after a larger series of boots. =:)

Signature · 1 line
Dominik