Skip to contentSkip to conversation

Second "CPU" of 1-core HyperThreading CPU not found in 2.6.13

DISCUSSION Chase Venters 5 participants 8 messages Aug 30, 2005

lore
Share & tools
lore
#0 lore raw

Greetings kind hackers...
I recently switched to 2.6.13 on my desktop. I noticed that the second
"CPU" (is there a better term to use in this HyperThreading scenario?) that used to be listed in /proc/cpuinfo is no longer present. Browsing over the archives, it appears as if someone else had this problem... their solution was to enable CONFIG_PM, but I already have CONFIG_PM enabled.
I have to boot with 'noapic' because I have my CD-Writer hanging off an
aic7xxx, and that driver goes into a nice error loop if I boot without it.
I'll include some lspci output below in case it is useful. There's one more
thing I noticed in the transition to 2.6.13, but I'm really not sure where I could start diagnosing it, and so any suggestions would be marvelous.
As I mentioned, this machine is my desktop. In the past, I've been able to
run compilers / other intensive tasks while listening to music in XMMS - the playback is never disrupted (indeed, on this P4 3.2ghz XMMS takes virtually none of the processor). Yet I've noticed enough momentary stops in sound output now to begin to suspect I've got some kind of problem.
Last kernels that were functional in both regards were 2.6.12.4 and 2.6.11.7.
Please note that I have not compiled with the new default tick rate of 250Hz
- I'm running 1000Hz, and I have also enabled the Preemptible kernel and BKL Preemption as I have in earlier kernels.

turbotaz linux-2.6.13 # lspci -v
0000:00:00.0 Host bridge: Intel Corporation 915G/P/GV/GL/PL/910GL Processor to I/O Controller (rev 04)
Subsystem: Intel Corporation 915G/P/GV/GL/PL/910GL Processor to I/O
Controller
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] #09 [2109]

0000:00:01.0 PCI bridge: Intel Corporation 915G/P/GV/GL/PL/910GL PCI Express Root Port (rev 04) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000e000-0000efff
Memory behind bridge: cdf00000-cfffffff
Prefetchable memory behind bridge: d0000000-dfffffff Expansion ROM at 0000e000 [disabled] [size=4K]
Capabilities: [88] #0d [0000]
Capabilities: [80] Power Management version 2
Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0
Enable+

        Capabilities: [a0] #10 [0141]

0000:00:1b.0 Class 0403: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03)
Subsystem: ASUSTeK Computer Inc.: Unknown device 813d
Flags: bus master, fast devsel, latency 0, IRQ 10
Memory at cdbf4000 (64-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-

        Capabilities: [70] #10 [0091]

0000:00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        I/O behind bridge: 0000d000-0000dfff
        Expansion ROM at 0000d000 [disabled] [size=4K]
        Capabilities: [40] #10 [0141]
        Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 

Enable+
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2

0000:00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])

        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: cde00000-cdefffff
        Prefetchable memory behind bridge: 0000000040000000-0000000040000000
        Expansion ROM at 0000c000 [disabled] [size=4K]
        Capabilities: [40] #10 [0141]
        Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 

Enable+
Capabilities: [90] #0d [0000]
Capabilities: [a0] Power Management version 2

0000:00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Flags: bus master, medium devsel, latency 0, IRQ 11 I/O ports at 9880 [size=32]

0000:00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Flags: bus master, medium devsel, latency 0, IRQ 3
I/O ports at 9c00 [size=32]

0000:00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Flags: bus master, medium devsel, latency 0, IRQ 5
I/O ports at a000 [size=32]

0000:00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Flags: bus master, medium devsel, latency 0, IRQ 10 I/O ports at a080 [size=32]

0000:00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Flags: bus master, medium devsel, latency 0, IRQ 11 Memory at cdbff800 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Capabilities: [58] #0a [20a0]

0000:00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d3) (prog-if 01 [Subtractive decode])

        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
        I/O behind bridge: 0000b000-0000bfff
        Memory behind bridge: cdc00000-cddfffff
        Prefetchable memory behind bridge: 0000000040100000-0000000040100000
        Expansion ROM at 0000b000 [disabled] [size=4K]
        Capabilities: [50] #0d [0000]

0000:00:1f.0 ISA bridge: Intel Corporation 82801FB/FR (ICH6/ICH6R) LPC Interface Bridge (rev 03)
Flags: bus master, medium devsel, latency 0

0000:00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Flags: bus master, medium devsel, latency 0, IRQ 5 I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at ffa0 [size=16]

0000:00:1f.2 IDE interface: Intel Corporation 82801FR/FRW (ICH6R/ICH6RW) SATA Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc.: Unknown device 2601
Flags: bus master, 66Mhz, medium devsel, latency 0, IRQ 3 I/O ports at ac00
I/O ports at a880 [size=4]
I/O ports at a800 [size=8]
I/O ports at a480 [size=4]
I/O ports at a400 [size=16]
Memory at cdbffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2

0000:00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
Subsystem: ASUSTeK Computer Inc.: Unknown device 80a6
Flags: medium devsel
I/O ports at 0400 [size=32]

0000:01:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc.: Unknown device 808b
Flags: bus master, medium devsel, latency 64, IRQ 7 Memory at cddfe800 (32-bit, non-prefetchable) Memory at cddf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2

0000:01:04.0 Unknown mass storage controller: Integrated Technology Express, Inc. IT/ITE8212 Dual channel ATA RAID controller (PCI version seems to be IT8212, embedded seems (rev 13)

        Subsystem: ASUSTeK Computer Inc.: Unknown device 813a
        Flags: bus master, 66Mhz, medium devsel, latency 0, IRQ 11
        I/O ports at bc00 [size=1025M]
        I/O ports at b480 [size=4]
        I/O ports at b400 [size=8]
        I/O ports at b080 [size=4]
        I/O ports at b000 [size=16]
        Expansion ROM at 00020000 [disabled]
        Capabilities: [80] Power Management version 2

0000:01:09.0 Multimedia controller: Sigma Designs, Inc. REALmagic Hollywood Plus DVD Decoder (rev 02)
Flags: bus master, medium devsel, latency 64, IRQ 4 Memory at cdc00000 (32-bit, non-prefetchable)
Capabilities: [40] Power Management version 1

0000:01:0a.0 SCSI storage controller: Adaptec AHA-7850 (rev 03)

        Subsystem: Adaptec AHA-2904/Integrated AIC-7850
        Flags: bus master, medium devsel, latency 64, IRQ 7
        I/O ports at b800 [disabled] [size=1025M]
        Memory at cddff000 (32-bit, non-prefetchable) [size=4K]
        Expansion ROM at 00010000 [disabled]
        Capabilities: [dc] Power Management version 1

0000:02:00.0 Ethernet controller: Marvell Technology Group Ltd. Gigabit Ethernet Controller (rev 15)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8053 Gigabit Ethernet
Controller (Asus)
Flags: bus master, fast devsel, latency 0, IRQ 4 Memory at cdefc000 (64-bit, non-prefetchable) [size=1024M] I/O ports at c800 [size=256]
Expansion ROM at 00020000 [disabled]
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable-

        Capabilities: [e0] #10 [0011]

0000:04:00.0 VGA compatible controller: nVidia Corporation NV40 [GeForce 6800 Ultra/GeForce 6800 GT] (rev a2) (prog-if 00 [VGA])
Subsystem: XFX Pine Group Inc. GEFORCE 6800 GT PCI-E
Flags: bus master, fast devsel, latency 0, IRQ 10
Memory at cf000000 (32-bit, non-prefetchable) [size=cdf00000] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at ce000000 (32-bit, non-prefetchable) [size=16M] Expansion ROM at 00020000 [disabled]
Capabilities: [60] Power Management version 2
Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-

        Capabilities: [78] #10 [0011]

Thanks,
Chase Venters

#1 lore raw
Quoted 4 lines · Chase Venters

Greetings kind hackers...
I recently switched to 2.6.13 on my desktop. I noticed that the second
"CPU" (is there a better term to use in this HyperThreading scenario?) that used to be listed in /proc/cpuinfo is no longer present. Browsing over the

[snip]

CONFIG_MPENTIUM4, CONFIG_SMP and CONFIG_SCHED_SMT enabled?

Signature · 3 lines
Jesper Juhl <[email protected]>
Don't top-post  http://www.catb.org/~esr/jargon/html/T/top-post.html
Plain text mails only, please      http://www.expita.com/nomime.html
#2 lore raw
Quoted 9 lines · Jesper Juhl
Quoted 4 lines · Chase Venters

Greetings kind hackers...
I recently switched to 2.6.13 on my desktop. I noticed that the second
"CPU" (is there a better term to use in this HyperThreading scenario?) that used to be listed in /proc/cpuinfo is no longer present. Browsing over the

[snip]

CONFIG_MPENTIUM4, CONFIG_SMP and CONFIG_SCHED_SMT enabled?

I have the same problem since linux-2.6.x Linux-2.4.20 and on had no problem with Hyper-Threading. My startup says:

CPU: Hyper-Threading is disabled. There is no enable/disable in the BIOS so I don't know what to do. It's an Intel D865PERL Motherboard so certainly Intel should know how to enable their CPUs.

Quoted 10 lines

--
Jesper Juhl <[email protected]>
Don't top-post http://www.catb.org/~esr/jargon/html/T/top-post.html
Plain text mails only, please http://www.expita.com/nomime.html
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Cheers,
Dick Johnson
Penguin : Linux version 2.6.13 on an i686 machine (5589.42 BogoMips). Warning : 98.36% of all statistics are fiction.
.
I apologize for the following. I tried to kill it with the above dot :

****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

#3 lore raw
In reply to Jesper Juhl
Quoted 10 lines · you
Quoted 5 lines · Chase Venters

Greetings kind hackers...
I recently switched to 2.6.13 on my desktop. I noticed that the
second "CPU" (is there a better term to use in this HyperThreading scenario?) that used to be listed in /proc/cpuinfo is no longer present. Browsing over the

[snip]

CONFIG_MPENTIUM4, CONFIG_SMP and CONFIG_SCHED_SMT enabled?

Yes in all three regards.

Thanks,
Chase

#4 lore raw

* Chase Venters <[email protected]>:

Quoted 3 lines
Quoted 1 line

CONFIG_MPENTIUM4, CONFIG_SMP and CONFIG_SCHED_SMT enabled?

Yes in all three regards.

Same here. Dual-Xeon 2.8Ghz, only 2 CPUs are being displayed.

Signature · 4 lines
Ralf Hildebrandt (i.A. des IT-Zentrums)         [email protected]
Charite - Universitätsmedizin Berlin            Tel.  +49 (0)30-450 570-155
Gemeinsame Einrichtung von FU- und HU-Berlin    Fax.  +49 (0)30-450 570-962
IT-Zentrum Standort CBF                 send no mail to [email protected]
#5 lore raw

* Ralf Hildebrandt <[email protected]>:

Quoted 7 lines

* Chase Venters <[email protected]>:

Quoted 3 lines
Quoted 1 line

CONFIG_MPENTIUM4, CONFIG_SMP and CONFIG_SCHED_SMT enabled?

Yes in all three regards.

Same here. Dual-Xeon 2.8Ghz, only 2 CPUs are being displayed.

After activating ACPI and power Management, HT works again.

Signature · 4 lines
Ralf Hildebrandt (i.A. des IT-Zentrums)         [email protected]
Charite - Universitätsmedizin Berlin            Tel.  +49 (0)30-450 570-155
Gemeinsame Einrichtung von FU- und HU-Berlin    Fax.  +49 (0)30-450 570-962
IT-Zentrum Standort CBF                 send no mail to [email protected]
#6 lore raw
In reply to Chase Venters
Quoted 12 lines · Chase Venters

Greetings kind hackers...
I recently switched to 2.6.13 on my desktop. I noticed that the second
"CPU" (is there a better term to use in this HyperThreading scenario?) that used to be listed in /proc/cpuinfo is no longer present. Browsing over the archives, it appears as if someone else had this problem... their solution was to enable CONFIG_PM, but I already have CONFIG_PM enabled.
I have to boot with 'noapic' because I have my CD-Writer hanging off an
aic7xxx, and that driver goes into a nice error loop if I boot without it.
I'll include some lspci output below in case it is useful. There's one more
thing I noticed in the transition to 2.6.13, but I'm really not sure where I could start diagnosing it, and so any suggestions would be marvelous.
As I mentioned, this machine is my desktop. In the past, I've been able to

Quoted 8 lines

run compilers / other intensive tasks while listening to music in XMMS - the playback is never disrupted (indeed, on this P4 3.2ghz XMMS takes virtually none of the processor). Yet I've noticed enough momentary stops in sound output now to begin to suspect I've got some kind of problem.
Last kernels that were functional in both regards were 2.6.12.4 and 2.6.11.7.
Please note that I have not compiled with the new default tick rate of 250Hz
- I'm running 1000Hz, and I have also enabled the Preemptible kernel and BKL Preemption as I have in earlier kernels.

I needed CONFIG_PM=y and CONFIG_ACPI=y to get ht working on 2.6.13.

regards,
Philippe Elie

#7 lore raw
Quoted 1 line

I needed CONFIG_PM=y and CONFIG_ACPI=y to get ht working on 2.6.13.

CONFIG_ACPI and CONFIG_PM are enabled here.

Thanks,
Chase Venters