2.6.13 does not boot on Eiger
I'm getting an MCA during early setup on Eiger, these are the last (and only) messages:
EFI v1.10 by HP: SALsystab=0x723feee9710 ACPI 2.0=0x723fe040000 HCDP=0x723fe0720d0 SMBIOS=0x7fffe000
booting generic kernel on platform hpzx1
PCDP: v1 at 0x723fe0720d0
Early serial console at MMIO 0xf0100005000 (options '9600n8') Number of logical nodes in system = 3
Number of memory chunks in system = 34
warning: skipping physical page 0
warning: skipping physical page 0
warning: skipping physical page 0
CONFIG_IA64_UNCACHED_ALLOCATOR is already disabled, and the kernel works fine on Tiger, so there must be some different problem. The config is attached. Note that this is already broken since at least 2.6.13-rc3, but 2.6.13-rc1 ist still ok.
Andreas.
Signature · 4 lines
Andreas Schwab, SuSE Labs, [email protected] SuSE Linux Products GmbH, Maxfeldstraße 5, 90409 Nürnberg, Germany Key fingerprint = 58CA 54C7 6D53 942B 1756 01D3 44D5 214B 8276 4ED5 "And now for something completely different."
Quoted 14 lines · Andreas Schwab
I'm getting an MCA during early setup on Eiger, these are the last (and only) messages:
EFI v1.10 by HP: SALsystab=0x723feee9710 ACPI 2.0=0x723fe040000 HCDP=0x723fe0720d0 SMBIOS=0x7fffe000
booting generic kernel on platform hpzx1
PCDP: v1 at0x723fe0720d0
Early serial console at MMIO0xf0100005000(options '9600n8') Number of logical nodes in system = 3
Number of memory chunks in system = 34
warning: skipping physical page 0
warning: skipping physical page 0
warning: skipping physical page 0
Quoted 4 lines
CONFIG_IA64_UNCACHED_ALLOCATORis already disabled, and the kernel works fine on Tiger, so there must be some different problem. The config is attached. Note that this is already broken since at least 2.6.13-rc3, but 2.6.13-rc1 ist still ok.
Does the MCA log say anything useful?
I used your .config and saw an MCA in i8042_flush() (IIP in __ia64_inb, BR0 in i8042_flush). Can you try turning off CONFIG_SERIO_I8042? This was fixed a while back, but maybe it got broken again. And the i8042 probe happens much later than your log indicates, so maybe you're seeing a different problem.
P.S. What is your firmware "acpiconfig" mode? My eiger is in "default" mode, in which accesses to non-existent I/O ports cause MCAs. But we don't officially support that yet because of issues like this. The supported modes allow accesses to non-existent ports by setting either "single-pci-domain" or "enable legacyprobe".
Quoted 1 line · Bjorn Helgaas
Does the MCA log say anything useful?
How can I find out?
Quoted 2 lines
P.S. What is your firmware "acpiconfig" mode? My eiger is in "default" mode,
Likewise.
Quoted 2 lines
The supported modes allow accesses to non-existent ports by setting either "single-pci-domain" or "enable legacyprobe".
Neither seem to be supported here.
Andreas.
Signature · 4 lines
Andreas Schwab, SuSE Labs, [email protected] SuSE Linux Products GmbH, Maxfeldstraße 5, 90409 Nürnberg, Germany Key fingerprint = 58CA 54C7 6D53 942B 1756 01D3 44D5 214B 8276 4ED5 "And now for something completely different."
Quoted 4 lines · Bjorn Helgaas
I used your .config and saw an MCA in
i8042_flush()(IIP in__ia64_inb, BR0 ini8042_flush). Can you try turning offCONFIG_SERIO_I8042? This was fixed a while back, but maybe it got broken again.
Oh, I remember now. I debugged this a while back. The i8042 fix was originally done in terms of ACPI, but recently changed to be PNP-based. So on ia64, we need CONFIG_PNP and CONFIG_PNPACPI.
These are turned off in your .config (and in all the configs in the tree). I'll post a patch to fix those.
Quoted 5 lines · Andreas Schwab
Quoted 1 line · Bjorn Helgaas
Does the MCA log say anything useful?
How can I find out?
On HP boxes, you can do "errdump mca" (for zx1 boxes) or "errdump all mca" (for sx1000 boxes) at the EFI shell. If you can boot a working kernel, salinfod will also extract the logs and drop them in /var/log/salinfo. There's a decoded/ directory, which is basically the same output as "errdump", and a raw/ directory, which contains binary files that can be run through a decoder (which is unfortunately proprietary).
Quoted 4 lines
Quoted 2 lines
P.S. What is your firmware "acpiconfig" mode? My eiger is in "default" mode,Likewise.
Type "acpiconfig" at the EFI shell prompt.
Quoted 4 lines · Bjorn Helgaas
If you can boot a working kernel, salinfod will also extract the logs and drop them in
/var/log/salinfo. There's a decoded/ directory, which is basically the same output as "errdump",
They all say: "UNCORRECTED PROCESSOR ERROR: Cache Check". I don't know what is needed from the files to make this useful.
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
P.S. What is your firmware "acpiconfig" mode? My eiger is in "default" mode,Likewise.
Type "acpiconfig" at the EFI shell prompt.
"Likewise" was actually referring to "default".
Andreas.
Signature · 4 lines
Andreas Schwab, SuSE Labs, [email protected] SuSE Linux Products GmbH, Maxfeldstraße 5, 90409 Nürnberg, Germany Key fingerprint = 58CA 54C7 6D53 942B 1756 01D3 44D5 214B 8276 4ED5 "And now for something completely different."