Skip to contentSkip to conversation

problem regarding KGDB on FC3

DISCUSSION umesh chandak 1 participant 1 message Oct 5, 2005

lore
Share & tools
lore
#0 lore raw

hi ,
I have applied a KGDB patch on FC3 for kernel

2.6.10 .
My connection is successful with command
target remote /dev/ttyS0

After pressing C for continuing i got some messages on console ,after that my target m/c did not start error messages are like this .
--------------------------------------------

(gdb) target remote /dev/ttyS0
Remote debugging using /dev/ttyS0
breakpoint () at kernel/kgdb.c:1446
1446 atomic_set(&kgdb_setting_breakpoint,
0);
(gdb) c
Continuing.
Linux version 2.6.10 ([email protected]) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #7 Wed Oct 5 11:37:32 IST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00
(usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000
(reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000
(reserved)
BIOS-e820: 0000000000100000 - 000000000f7f0000
(usable)
BIOS-e820: 000000000f7f0000 - 000000000f7f3000 (ACPI
NVS)
BIOS-e820: 000000000f7f3000 - 000000000f800000 (ACPI
data)
BIOS-e820: 000000000f800000 - 0000000010000000
(reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000
(reserved)
Waiting for connection from remote gdb...
0MB HIGHMEM available.
247MB LOWMEM available.
DMI 2.3 present.
ACPI: PM-Timer IO Port: 0x4008
Built 1 zonelists
Kernel command line: ro root=/dev/hda6 rootfstype=ext3 kgdbwait kgdb8250=1,57600
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes) Detected 2412.550 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 247512k/253888k available (2441k kernel code, 5816k reserved, 623k data, 184k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok.
Security Framework v1.0.0 initialized Capability LSM initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0a20)
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf9d80, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to [email protected]
** so I can fix the driver.
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled) audit(1128469838.545:0): initialized Registering GDB sysrq handler
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: probe of vesafb0 failed with error -6
ACPI: Processor [CPU0] (supports 2 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: Maximum main memory to use for agp memory:
196M
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xe0000000
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Couldn't register serial port UAR1: -16
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

______________________________________________________
Yahoo! for Good
Donate to the Hurricane Katrina relief effort.
http://store.yahoo.com/redcross-donate3/