Skip to contentSkip to conversation

dumb muliport serial cards not supported in 2.6.13.4 ???

DISCUSSION Jarek 2 participants 3 messages Oct 27, 2005

lore
Share & tools
lore

Jarek

author
#0 lore raw

Hi all!

I've PCM 3643, 8 port dumb multiport serial card from Advantech. This card works nice with 2.6.12 but with 2.6.13.4 I can see only two
ports!

	This is dumb 8250 (exactly: 16550A) multiport board. In 2.6.12 I've the

following settings:

CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_MULTIPORT=y
CONFIG_SERIAL_8250_RSA=y
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y

I've tried to setup same in 2.6.13.4, but it claims:
.config:761: trying to assign nonexistent symbol SERIAL_8250_MULTIPORT

I suspect that this is the problematic setting but there is nothing about this in any Changelog.

What should I do ?

Jarek.

#1 lore raw
Quoted 19 lines · Jarek

Hi all!

I've PCM 3643, 8 port dumb multiport serial card from Advantech. This card works nice with 2.6.12 but with 2.6.13.4 I can see only two
ports!

	This is dumb 8250 (exactly: 16550A) multiport board. In 2.6.12 I've the

following settings:

CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=4
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_MULTIPORT=y
CONFIG_SERIAL_8250_RSA=y
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y

Quoted 7 lines

I've tried to setup same in 2.6.13.4, but it claims:
.config:761: trying to assign nonexistent symbol SERIAL_8250_MULTIPORT

I suspect that this is the problematic setting but there is nothing about this in any Changelog.

What should I do ?

Please send the kernel messages from this kernel so we can see what's going on. (this would be useful whatever.)

At a guess you need to increase CONFIG_SERIAL_8250_NR_UARTS. It now represents the _total_ number of ports.

Signature · 3 lines
Russell King
 Linux kernel    2.6 ARM Linux   - http://www.arm.linux.org.uk/
 maintainer of:  2.6 Serial core
author
#2 lore raw

Dnia 27-10-2005, czw o godzinie 09:08 +0100, Russell King napisał(a):

Quoted 4 lines

Please send the kernel messages from this kernel so we can see what's going on. (this would be useful whatever.)

From dmesg:

Serial: 8250/16550 driver $Revision: 1.90 $ 16 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

$cat /proc/tty/driver/serial:

serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:47 rx:0 RTS|DTR 1: uart:16550A port:000002F8 irq:3 tx:0 rx:0 CTS|DSR 2: uart:16550A port:00000240 irq:5 tx:2828 rx:2826 fe:81 3: uart:16550A port:00000248 irq:5 tx:0 rx:0 RTS|CTS|DTR|DSR 4: uart:unknown port:00000000 irq:0
5: uart:unknown port:00000000 irq:0
6: uart:unknown port:00000000 irq:0
7: uart:unknown port:00000000 irq:0
8: uart:unknown port:00000000 irq:0
9: uart:unknown port:00000000 irq:0
10: uart:unknown port:00000000 irq:0
11: uart:unknown port:00000000 irq:0
12: uart:unknown port:00000000 irq:0
13: uart:unknown port:00000000 irq:0
14: uart:unknown port:00000000 irq:0
15: uart:unknown port:00000000 irq:0

setserial /dev/ttyS4 port 0x250 irq 5 uart 16550A ^fourport Cannot set serial info: Invalid argument

(ports 2-9 are from PCM3643)

$grep CONFIG_SERIAL .config
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=16
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
CONFIG_SERIAL_8250_RSA=y
# CONFIG_SERIAL_8250_FOURPORT is not set
# CONFIG_SERIAL_8250_ACCENT is not set
# CONFIG_SERIAL_8250_BOCA is not set
# CONFIG_SERIAL_8250_HUB6 is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set

best regards
Jarek