Skip to contentSkip to conversation

SCSI adaptec 19160 speed - 2.6.14-rt13 - Q for scsi experts

DISCUSSION art 2 participants 2 messages Nov 30, 2005

lore
Share & tools
lore

art

author
#0 lore raw

Re: SCSI adaptec 19160 speed - 2.6.14-rt13 - Q for scsi experts

Quoted 53 lines · art
Quoted 53 lines

SCSI adaptec 19160 speed - 2.6.14-rt13 - Q for scsi experts

Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
Vendor: COMPAQ Model: BF14688286 Rev: HPB3
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:2:0: Tagged Queuing enabled. Depth 64 target0:0:2: Beginning Domain Validation
target0:0:2: wide asynchronous.
target0:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63) target0:0:2: Ending Domain Validation
SCSI device sdb: 286749488 512-byte hdwr sectors (146816 MB) SCSI device sdb: drive cache: write through
SCSI device sdb: 286749488 512-byte hdwr sectors (146816 MB) SCSI device sdb: drive cache: write through
sdb: sdb1
Attached scsi disk sdb at scsi0, channel 0, id 2, lun 0
Vendor: COMPAQ Model: BF14688286 Rev: HPB3
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:5:0: Tagged Queuing enabled. Depth 64 target0:0:5: Beginning Domain Validation
target0:0:5: wide asynchronous.
target0:0:5: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 63) target0:0:5: Ending Domain Validation
SCSI device sdc: 286749488 512-byte hdwr sectors (146816 MB) SCSI device sdc: drive cache: write through
SCSI device sdc: 286749488 512-byte hdwr sectors (146816 MB) SCSI device sdc: drive cache: write through
sdc: sdc1
Attached scsi disk sdc at scsi0, channel 0, id 5, lun 0

# hdparm -tT /dev/sdb
/dev/sdb:
Timing cached reads:   2316 MB in  2.00 seconds = 1157.90 MB/sec
Timing buffered disk reads:  268 MB in  3.00 seconds =  89.26 MB/sec
# hdparm -tT /dev/sdc

/dev/sdc:

Timing cached reads:   2512 MB in  2.00 seconds = 1255.49 MB/sec
Timing buffered disk reads:  268 MB in  3.00 seconds =  89.32 MB/sec
# hdparm -tT /dev/sdb & hdparm -tT /dev/sdc &
[1] 3314
[2] 3315

/dev/sdb:
/dev/sdc:
Timing cached reads: Timing cached reads: 1228 MB in 2.00 seconds = 613.88 MB/sec
1316 MB in 1.99 seconds = 659.73 MB/sec
Timing buffered disk reads: Timing buffered disk reads:

174 MB in  3.00 seconds =  57.91 MB/sec
170 MB in  3.05 seconds =  55.75 MB/sec

------------------------------------------------------------------------------------------

Quoted 1 line
Quoted 1 line

pci is 66Mhz theoretical throuhput ~ 250MB/s

And pci at 33mhz can do 130MB/s or so. With a bit over overhead those numbers sure look awful close to what a 33mhz pci bus can handle.

Quoted 10 lines
Quoted 10 lines

controller adaptec asc-19160
discs are 146GB-15krpm-cheetah

one disc transfer 89MB/s

adaptec speed with 2 disc on one channel = 57.91+55.75 = 113.66MB/s

71% of 160MB/s channel speed i expected ~90%

any clue?

PCI bus not at 66mhz perhaps? Is it an add in card on onboard? I wonder if a pci bus that supports 66mhz has to drop everything to 33mhz if any of the cards installed are 33mhz only. Having never tried I don't know.

Len Sorensen

--------------------------------------------------------------
--------------------------------------------------------------

# /sbin/lspci -v

02:00.0 SCSI storage controller: Adaptec AIC-7892B U160/m (rev 02)
Subsystem: Adaptec 19160 Ultra160 SCSI Controller
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 16 BIST result: 00
I/O ports at a000 [disabled] [size=256]
Memory at e302a000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2

02:02.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: Belkin Root Hub
Flags: bus master, medium devsel, latency 32, IRQ 16 Memory at e3028000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2

02:04.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Adaptec: Unknown device 0030
Flags: bus master, medium devsel, latency 32, IRQ 16
Memory at e302b000 (32-bit, non-prefetchable) [size=2K]
Memory at e3020000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2

3 cards on same 16-int Adaptec 19160 at 66Mhz
but---33Mhz ieee1394a ---- subsystem: Adaptec ???

xboom

#1 lore raw
Quoted 3 lines · art

Re: SCSI adaptec 19160 speed - 2.6.14-rt13 - Q for scsi experts

On Tue, Nov 29, 2005 at 07:36:44PM -0600, art wrote:

[snip]

Quoted 75 lines
Quoted 24 lines
Quoted 24 lines
# hdparm -tT /dev/sdb
/dev/sdb:
Timing cached reads:   2316 MB in  2.00 seconds = 1157.90 MB/sec
Timing buffered disk reads:  268 MB in  3.00 seconds =  89.26 MB/sec
# hdparm -tT /dev/sdc

/dev/sdc:

Timing cached reads:   2512 MB in  2.00 seconds = 1255.49 MB/sec
Timing buffered disk reads:  268 MB in  3.00 seconds =  89.32 MB/sec
# hdparm -tT /dev/sdb & hdparm -tT /dev/sdc &
[1] 3314
[2] 3315

/dev/sdb:
/dev/sdc:
Timing cached reads: Timing cached reads: 1228 MB in 2.00 seconds = 613.88 MB/sec
1316 MB in 1.99 seconds = 659.73 MB/sec
Timing buffered disk reads: Timing buffered disk reads:

174 MB in  3.00 seconds =  57.91 MB/sec
170 MB in  3.05 seconds =  55.75 MB/sec

------------------------------------------------------------------------------------------

Quoted 1 line
Quoted 1 line

pci is 66Mhz theoretical throuhput ~ 250MB/s

And pci at 33mhz can do 130MB/s or so. With a bit over overhead those numbers sure look awful close to what a 33mhz pci bus can handle.

Quoted 10 lines
Quoted 10 lines

controller adaptec asc-19160
discs are 146GB-15krpm-cheetah

one disc transfer 89MB/s

adaptec speed with 2 disc on one channel = 57.91+55.75 = 113.66MB/s

71% of 160MB/s channel speed i expected ~90%

any clue?

PCI bus not at 66mhz perhaps? Is it an add in card on onboard? I wonder if a pci bus that supports 66mhz has to drop everything to 33mhz if any of the cards installed are 33mhz only. Having never tried I don't know.

Len Sorensen

--------------------------------------------------------------
--------------------------------------------------------------

# /sbin/lspci -v

02:00.0 SCSI storage controller: Adaptec AIC-7892B U160/m (rev 02)
Subsystem: Adaptec 19160 Ultra160 SCSI Controller
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 16 BIST result: 00
I/O ports at a000 [disabled] [size=256]
Memory at e302a000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2

02:02.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: Belkin Root Hub
Flags: bus master, medium devsel, latency 32, IRQ 16 Memory at e3028000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2

02:04.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Adaptec: Unknown device 0030
Flags: bus master, medium devsel, latency 32, IRQ 16
Memory at e302b000 (32-bit, non-prefetchable) [size=2K]
Memory at e3020000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2

Quoted 3 lines

3 cards on same 16-int Adaptec 19160 at 66Mhz
but---33Mhz ieee1394a ---- subsystem: Adaptec ???

Hmm, seeing your mail got me thinking about how my own disks perform

# lspci -v
00:0b.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
        Subsystem: Adaptec 29160N Ultra160 SCSI Controller
        Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
        BIST result: 00
        I/O ports at 9800 [disabled] [size=256]
        Memory at e3000000 (64-bit, non-prefetchable) [size=4K]
        Expansion ROM at 30000000 [disabled] [size=128K]
        Capabilities: [dc] Power Management version 2

about the disk (10K RPM IBM UltraStar) from dmesg :

[   43.387178]   Vendor: IBM       Model: DDYS-T36950N      Rev: S96H
[   43.406176]   Type:   Direct-Access                      ANSI SCSI
revision: 03
[   43.424651] scsi0:A:6:0: Tagged Queuing enabled.  Depth 200
[   43.442952]  target0:0:6: Beginning Domain Validation
[   43.464011]  target0:0:6: wide asynchronous.
[   43.486866]  target0:0:6: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns,
offset 63)
[   43.514788]  target0:0:6: Ending Domain Validation
[   45.584696] SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
[   45.604490] SCSI device sda: drive cache: write back
[   45.623781] SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
[   45.643575] SCSI device sda: drive cache: write back
[   45.661953]  sda: sda1 sda2 sda3 sda4
[   45.691968] sd 0:0:6:0: Attached scsi disk sda
# hdparm -tT /dev/sda

/dev/sda:
Timing cached reads: 904 MB in 2.00 seconds = 451.17 MB/sec
Timing buffered disk reads: 84 MB in 3.05 seconds = 27.52 MB/sec

Not exactely impressive numbers here...

--
Jesper Juhl <[email protected]>
Don't top-post http://www.catb.org/~esr/jargon/html/T/top-post.html
Plain text mails only, please http://www.expita.com/nomime.html