ALCHEMY: AU1200 I2C modifications

index f00ec3b..a2638c8 100644
@@ -76,6 +76,43 @@ void __init board_setup(void)
 #endif
 	bcsr->pcmcia = 0x0000; /* turn off PCMCIA power */
 
+#if defined(CONFIG_I2C_AU1550) && defined(CONFIG_MIPS_DB1200)
+	{
+	u32 freq0, clksrc;
+
+	/* Select SMBUS in CPLD */
+	bcsr->resets &= ~(BCSR_RESETS_PCS0MUX);
+
+	pin_func = au_readl(SYS_PINFUNC);
+	au_sync();
+	pin_func &= ~(3<<17 | 1<<4);
+	/* Set GPIOs correctly */
+	pin_func |= 2<<17;
+	au_writel(pin_func, SYS_PINFUNC);
+	au_sync();
+
+	/* The i2c driver depends on 50Mhz clock */
+	freq0 = au_readl(SYS_FREQCTRL0);
+	au_sync();
+	freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
+	freq0 |= (3<<SYS_FC_FRDIV1_BIT);
+	/* 396Mhz / (3+1)*2 == 49.5Mhz */
+	au_writel(freq0, SYS_FREQCTRL0);
+	au_sync();
+	freq0 |= SYS_FC_FE1;
+	au_writel(freq0, SYS_FREQCTRL0);
+	au_sync();
+
+	clksrc = au_readl(SYS_CLKSRC);
+	au_sync();
+	clksrc &= ~0x01f00000;
+	/* bit 22 is EXTCLK0 for PSC0 */
+	clksrc |= (0x3 << 22);
+	au_writel(clksrc, SYS_CLKSRC);
+	au_sync();
+	}
+#endif
+
 #ifdef CONFIG_MIPS_MIRAGE
 	/* enable GPIO[31:0] inputs */
 	au_writel(0, SYS_PININPUTEN);

index d06edce..4508629 100644
@@ -35,7 +35,15 @@
 #include <linux/i2c.h>
 
 #include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1550.h>
+#if defined(CONFIG_MIPS_PB1550)
+ #include <asm/mach-pb1x00/pb1550.h>
+#endif
+#if defined(CONFIG_MIPS_PB1200)
+ #include <asm/mach-pb1x00/pb1200.h>
+#endif
+#if defined(CONFIG_MIPS_DB1200)
+ #include <asm/mach-db1x00/db1200.h>
+#endif
 #include <asm/mach-au1x00/au1xxx_psc.h>
 
 #include "i2c-au1550.h"

@@ -118,13 +126,20 @@ do_address(struct i2c_au1550_data *adap,
 
 	/* Reset the FIFOs, clear events.
 	*/
-	sp->psc_smbpcr = PSC_SMBPCR_DC;
+	stat = sp->psc_smbstat;
 	sp->psc_smbevnt = PSC_SMBEVNT_ALLCLR;
 	au_sync();
-	do {
-		stat = sp->psc_smbpcr;
+
+	if (!(stat & PSC_SMBSTAT_TE) || !(stat & PSC_SMBSTAT_RE))
+	{
+		sp->psc_smbpcr = PSC_SMBPCR_DC;
 		au_sync();
-	} while ((stat & PSC_SMBPCR_DC) != 0);
+		do {
+			stat = sp->psc_smbpcr;
+			au_sync();
+		} while ((stat & PSC_SMBPCR_DC) != 0);
+		udelay(50);
+	}
 
 	/* Write out the i2c chip address and specify operation
 	*/

@@ -367,7 +382,7 @@ static struct i2c_au1550_data pb1550_i2c
 	SMBUS_PSC_BASE, 200, 200
 };
 
-static struct i2c_adapter pb1550_board_adapter = {
+struct i2c_adapter pb1550_board_adapter = {
 	name:              "pb1550 adapter",
 	id:                I2C_HW_AU1550_PSC,
 	algo:              NULL,

@@ -376,6 +391,8 @@ static struct i2c_adapter pb1550_board_a
 	client_unregister: pb1550_unreg,
 };
 
+EXPORT_SYMBOL(pb1550_board_adapter);
+
 /* BIG hack to support the control interface on the Wolfson WM8731
  * audio codec on the Pb1550 board.  We get an address and two data
  * bytes to write, create an i2c message, and send it across the

index 8e5fb3c..45a05c8 100644
@@ -43,6 +43,11 @@
 #define PSC3_BASE_ADDR		0xb0d00000
 #endif
 
+#ifdef CONFIG_SOC_AU1200
+#define PSC0_BASE_ADDR         0xb1a00000
+#define PSC1_BASE_ADDR         0xb1b00000
+#endif
+
 /* The PSC select and control registers are common to
  * all protocols.
  */

@@ -506,7 +511,7 @@ typedef struct	psc_smb {
 
 /* Transmit register control.
 */
-#define PSC_SMBTXRX_RSR		(1 << 30)
+#define PSC_SMBTXRX_RSR		(1 << 28)
 #define PSC_SMBTXRX_STP		(1 << 29)
 #define PSC_SMBTXRX_DATAMASK	(0xff)