Skip to contentSkip to conversation

omap 5912 linux 2.6.15rc2

DISCUSSION Rahul 2 participants 2 messages Dec 5, 2005

lore
Share & tools
lore

Rahul

author
#0 lore raw

Hi group,

I am presently working on omap5912 osk. First i used the linux from montavista i.e. 2.4.20 and was able to successfully mount and run the usb on it.

But recently i have downloaded the latest kernel i.e. 2.6.15rc2.
The problem is that i am unable to mount usb on it,though lot of drivers r detected if i dmesg like usb hub found, usb core found, udc driver found, mass storage initialized, scsi subsystem initialized, omap ohci...etc

Please suggest something if someone has mounted usb successfully on 2.6.15.Do i need to apply some patch or add something..??

I am attaching the message which i receive by dmesg

Thanks
Rahul

U-Boot 1.1.2 (Oct 26 2005 - 16:18:08)

U-Boot code: 11080000 -> 11096144 BSS: -> 1109A914 RAM Configuration:
Bank #0: 10000000 32 MB
Micron StrataFlash MT28F128J3 device initialized

Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
OMAP5912 OSK # bootm 0x100000 ## Booting image at 00100000 ...
   Image Name:   Linux-2.6.15-rc2-omap1-g0cab20fd
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1389496 Bytes =  1.3 MB

Load Address: 10008000
Entry Point: 10008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux............................................................................................. done, booting the kernel.

Linux version 2.6.15-rc2-omap1-g0cab20fd (root@brahma) (gcc version 3.3.2) #2 Wed Nov 23 20:00:45 IST 2005

CPU: ARM926EJ-Sid(wb) [41069263] revision 3 (ARMv5TEJ)

Machine: TI-OSK

Memory policy: ECC disabled, Data cache writeback

OMAP1611b revision 2 handled as 16xx id: 5b058f7948871d18

SRAM: Mapped pa 0x00020000 to va 0xd0000000 size: 0x3f000

Clocks: ARM_SYSST: 0x0000 DPLL_CTL: 0x2833 ARM_CKCTL: 0x3000

Clocking rate (xtal/DPLL1/MPU): 12.0/192.0/192.0 MHz

CPU0: D VIVT write-back cache

CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets

Built 1 zonelists

Kernel command line: console=ttyS0,115200n8 noinitrd ip=10.64.42.25:10.64.12.95:10.64.1.1:255.255.0.0:osk:eth0:off root=/dev/nfs rw nfsroot=10.64.12.95:/data/rootfs2.6,nolock mem=32M

Total of 128 interrupts in 4 interrupt banks

OMAP GPIO hardware version 1.0

MUX: initialized M7_1610_GPIO62

PID hash table entries: 256 (order: 8, 4096 bytes)

Console: colour dummy device 80x30

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 32MB = 32MB total

Memory: 29328KB available (2378K code, 481K data, 120K init)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

OMAP DMA hardware version 1

DMA capabilities: 000c0000:00000000:01ff:003f:007f

Initializing OMAP McBSP system

USB: hmc 16, usb0 2 wires

i2c_omap: bus 0 rev2.2 at 100 KHz

tps65010: version 2 May 2005

MUX: initialized N14_1610_UWIRE_CS0

MUX: initialized P15_1610_UWIRE_CS3

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

NetWinder Floating Point Emulator V0.97 (double precision)

OMAP OCPI interconnect driver loaded

Power Management for TI OMAP.

MUX: initialized T20_1610_LOW_PWR

JFFS version 1.0, (C) 1999, 2000 Axis Communications AB

JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered

omapfb: configured for panel osk

omapfb-lcdc: init

MUX: initialized PWL

omapfb-lcdc: Pixel clock divider value is obsolete.

omapfb-lcdc: Try to set pixel_clock to 8000 and pcd to 0 in drivers/video/omap/lcd_osk.c and submit a patch.

Console: switching to colour frame buffer device 30x40

omapfb: initialized vram=153600 pixclock 8000 kHz hfreq 20.1 kHz vfreq 63.3 Hz

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0xfffb0000 (irq = 46) is a ST16654

RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize

loop: loaded (max 8 devices)

PPP generic driver version 2.4.2

smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <[email protected]>

eth0: SMC91C94 (rev 9) at c2852300 IRQ 160 [nowait]

eth0: Ethernet addr: 00:0e:99:02:05:93

i2c /dev entries driver

omapflash.0: Found 1 x16 devices at 0x0 in 16-bit bank

omapflash.0: Found 1 x16 devices at 0x1000000 in 16-bit bank

Intel/Sharp Extended Query Table at 0x0031

Using buffer write method

cfi_cmdset_0001: Erase suspend on write enabled

Creating 4 MTD partitions on "omapflash.0":

0x00000000-0x00020000 : "bootloader"

0x00020000-0x00040000 : "params"

0x00040000-0x00240000 : "kernel"

0x00240000-0x02000000 : "filesystem"

MUX: initialized W11_1610_CF_CD1

MUX: initialized P11_1610_CF_CD2

MUX: initialized R11_1610_CF_IOIS16

MUX: initialized V10_1610_CF_IREQ

MUX: initialized W10_1610_CF_RESET

omap_cf: cs2 on irq 222

usbmon: debugfs is not available

MUX: initialized W8_1610_GPIO9

MUX: initialized W4_USB_HIGHZ

ohci ohci: OMAP OHCI

ohci ohci: new USB bus registered, assigned bus number 1

ohci ohci: irq 38, io mem 0xfffba000

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 3 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

mice: PS/2 mouse device common for all mice

OMAP Keypad Driver

input: device omap-keypad is statically allocated, will not register

Please convert to input_allocate_device() or contact [email protected]

NET: Registered protocol family 2

IP route cache hash table entries: 512 (order: -1, 2048 bytes)

TCP established hash table entries: 2048 (order: 1, 8192 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

TCP bic registered

NET: Registered protocol family 1

Disabling unused clock "usb_dc_ck"... done

FIXME: Clock "tc2_ck" seems unused

Disabling unused clock "tc1_ck"... done

Skipping reset check for DSP domain clock "dsptim_ck"

Skipping reset check for DSP domain clock "dspxor_ck"

Skipping reset check for DSP domain clock "dspper_ck"

eth0: link up

IP-Config: Complete:

      device=eth0, addr=10.64.42.25, mask=255.255.0.0, gw=10.64.1.1,

     host=osk, domain=, nis-domain=(none),

     bootserver=10.64.12.95, rootserver=10.64.12.95, rootpath=

Looking up port of RPC 100003/2 on 10.64.12.95

Looking up port of RPC 100005/1 on 10.64.12.95

VFS: Mounted root (nfs filesystem).

Freeing init memory: 120K

init started: BusyBox v1.00-pre8 (2004.03.05-22:18+0000) multi-call binary

******************************************
Starting System Init for OMAP5912OSK
******************************************

Please press Enter to activate this console.

BusyBox v1.00-pre8 (2004.03.05-22:18+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands.

-sh: can't access tty; job control turned off
#

*********************************************************************************************************
*********************************************************************************************************

U-Boot 1.1.2 (Oct 26 2005 - 16:18:08)

U-Boot code: 11080000 -> 11096144 BSS: -> 1109A914 RAM Configuration:
Bank #0: 10000000 32 MB
Micron StrataFlash MT28F128J3 device initialized

Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
OMAP5912 OSK # bootm 0x100000 ## Booting image at 00100000 ...
   Image Name:   Linux-2.6.15-rc2-omap1-g0cab20fd
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1475388 Bytes =  1.4 MB

Load Address: 10008000
Entry Point: 10008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................... done, booting the kernel.

Linux version 2.6.15-rc2-omap1-g0cab20fd (root@brahma) (gcc version 3.3.2) #4 Thu Dec 1 17:36:52 IST 2005

CPU: ARM926EJ-Sid(wb) [41069263] revision 3 (ARMv5TEJ)

Machine: TI-OSK

Memory policy: ECC disabled, Data cache writeback

OMAP1611b revision 2 handled as 16xx id: 5b058f7948871d18

SRAM: Mapped pa 0x00020000 to va 0xd0000000 size: 0x3f000

Clocks: ARM_SYSST: 0x0000 DPLL_CTL: 0x2833 ARM_CKCTL: 0x3000

Clocking rate (xtal/DPLL1/MPU): 12.0/192.0/192.0 MHz

CPU0: D VIVT write-back cache

CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets

Built 1 zonelists

Kernel command line: console=ttyS0,115200n8 noinitrd rw ip=dhcp root=/dev/nfs nfsroot=10.64.12.95:/data/rootfs2.6,nolock mem=30M

Total of 128 interrupts in 4 interrupt banks

OMAP GPIO hardware version 1.0

MUX: initialized M7_1610_GPIO62

PID hash table entries: 128 (order: 7, 2048 bytes)

Console: colour dummy device 80x30

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Memory: 30MB = 30MB total

Memory: 27192KB available (2536K code, 495K data, 124K init)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

OMAP DMA hardware version 1

DMA capabilities: 000c0000:00000000:01ff:003f:007f

Initializing OMAP McBSP system

MUX: initialized W4_USB_PUEN

USB: hmc 0, usb0 2 wires (dev)

i2c_omap: bus 0 rev2.2 at 100 KHz

tps65010: version 2 May 2005

MUX: initialized N14_1610_UWIRE_CS0

MUX: initialized P15_1610_UWIRE_CS3

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

NetWinder Floating Point Emulator V0.97 (double precision)

OMAP OCPI interconnect driver loaded

Power Management for TI OMAP.

MUX: initialized T20_1610_LOW_PWR

JFFS version 1.0, (C) 1999, 2000 Axis Communications AB

JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered

omapfb: configured for panel osk

omapfb-lcdc: init

MUX: initialized PWL

omapfb-lcdc: Pixel clock divider value is obsolete.

omapfb-lcdc: Try to set pixel_clock to 8000 and pcd to 0 in drivers/video/omap/lcd_osk.c and submit a patch.

Console: switching to colour frame buffer device 30x40

omapfb: initialized vram=153600 pixclock 8000 kHz hfreq 20.1 kHz vfreq 63.3 Hz

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0xfffb0000 (irq = 46) is a ST16654

RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize

loop: loaded (max 8 devices)

PPP generic driver version 2.4.2

smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <[email protected]>

eth0: SMC91C94 (rev 9) at c2052300 IRQ 160 [nowait]

eth0: Ethernet addr: 00:0e:99:02:05:93

i2c /dev entries driver

omapflash.0: Found 1 x16 devices at 0x0 in 16-bit bank

omapflash.0: Found 1 x16 devices at 0x1000000 in 16-bit bank

Intel/Sharp Extended Query Table at 0x0031

Using buffer write method

cfi_cmdset_0001: Erase suspend on write enabled

Creating 4 MTD partitions on "omapflash.0":

0x00000000-0x00020000 : "bootloader"

0x00020000-0x00040000 : "params"

0x00040000-0x00240000 : "kernel"

0x00240000-0x02000000 : "filesystem"

MUX: initialized W11_1610_CF_CD1

MUX: initialized P11_1610_CF_CD2

MUX: initialized R11_1610_CF_IOIS16

MUX: initialized V10_1610_CF_IREQ

MUX: initialized W10_1610_CF_RESET

omap_cf: cs2 on irq 222

usbmon: debugfs is not available

116x: driver isp116x-hcd, 05 Aug 2005

sl811: driver sl811-hcd, 19 May 2005

usbcore: registered new driver usblp

drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

usbcore: registered new driver usbhid

drivers/usb/input/hid-core.c: v2.6:USB HID core driver

usbcore: registered new driver asix

usbcore: registered new driver cdc_ether

usbcore: registered new driver net1080

usbcore: registered new driver zaurus

udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)

udc: OMAP UDC rev 3.6

udc: hmc mode 0, integrated transceiver

udc: fifo mode 3, 392 bytes not used

usb0: Ethernet Gadget, version: May Day 2005

usb0: using omap_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep3in-int

usb0: MAC 6e:d7:e8:91:90:93

usb0: HOST MAC 8a:f0:df:c4:0f:b9

usb0: RNDIS ready

mice: PS/2 mouse device common for all mice

OMAP Keypad Driver

input: device omap-keypad is statically allocated, will not register

Please convert to input_allocate_device() or contact [email protected]

NET: Registered protocol family 2

IP route cache hash table entries: 256 (order: -2, 1024 bytes)

TCP established hash table entries: 1024 (order: 0, 4096 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

TCP bic registered

NET: Registered protocol family 1

Disabling unused clock "usb_dc_ck"... done

FIXME: Clock "tc2_ck" seems unused

Disabling unused clock "tc1_ck"... done

Skipping reset check for DSP domain clock "dsptim_ck"

Skipping reset check for DSP domain clock "dspxor_ck"

Skipping reset check for DSP domain clock "dspper_ck"

eth0: link up

Sending DHCP requests ., OK

IP-Config: Got DHCP answer from 10.64.2.1, my address is 10.64.12.234

IP-Config: Complete:

      device=eth0, addr=10.64.12.234, mask=255.255.0.0, gw=10.64.1.1,

     host=10.64.12.234, domain=dhcpee.iitd.ac.in, nis-domain=(none),

     bootserver=10.64.2.1, rootserver=10.64.12.95, rootpath=

Looking up port of RPC 100003/2 on 10.64.12.95

Looking up port of RPC 100005/1 on 10.64.12.95

VFS: Mounted root (nfs filesystem).

Freeing init memory: 124K

init started: BusyBox v1.00-pre8 (2004.03.05-22:18+0000) multi-call binary

******************************************
Starting System Init for OMAP5912OSK
******************************************

Please press Enter to activate this console.

BusyBox v1.00-pre8 (2004.03.05-22:18+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands.

-sh: can't access tty; job control turned off
#

#1 lore raw

Hi Rahul,

Please, read the thread "OSK5912 USB Port Problem" in this mailing list (its quite recent, November 2005). I successfully tried a 2.6.15 kernel, but I have to use a patch Tony Lindgren recommended me on that thread. The problem was something related to the reset of the USB clock at boot. This problem affects kernel 2.6.12 and beyond. Other possibility is to disable the CONFIG_OMAP_RESET_CLOCKS option when compiling the kernel.

This is the patch:

http://linux.omap.com/pipermail/linux-omap-open-source/2005-August/004818.html

Best regards,

Jose

Quoted 604 lines · Rahul

Hi group,

I am presently working on omap5912 osk. First i used the linux from montavista i.e. 2.4.20 and was able to successfully mount and run the usb on it.

But recently i have downloaded the latest kernel i.e. 2.6.15rc2.
The problem is that i am unable to mount usb on it,though lot of drivers r detected if i dmesg like usb hub found, usb core found, udc driver found, mass storage initialized, scsi subsystem initialized, omap ohci...etc

Please suggest something if someone has mounted usb successfully on 2.6.15.Do i need to apply some patch or add something..??

I am attaching the message which i receive by dmesg

Thanks Rahul

------------------------------------------------------------------------

U-Boot 1.1.2 (Oct 26 2005 - 16:18:08)

U-Boot code: 11080000 -> 11096144 BSS: -> 1109A914 RAM Configuration:
Bank #0: 10000000 32 MB
Micron StrataFlash MT28F128J3 device initialized

Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
OMAP5912 OSK # bootm 0x100000 ## Booting image at 00100000 ...
  Image Name:   Linux-2.6.15-rc2-omap1-g0cab20fd
  Image Type:   ARM Linux Kernel Image (uncompressed)
  Data Size:    1389496 Bytes =  1.3 MB

Load Address: 10008000
Entry Point: 10008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux............................................................................................. done, booting the kernel.

Linux version 2.6.15-rc2-omap1-g0cab20fd (root@brahma) (gcc version 3.3.2) #2 Wed Nov 23 20:00:45 IST 2005

CPU: ARM926EJ-Sid(wb) [41069263] revision 3 (ARMv5TEJ)

Machine: TI-OSK

Memory policy: ECC disabled, Data cache writeback

OMAP1611b revision 2 handled as 16xx id: 5b058f7948871d18

SRAM: Mapped pa 0x00020000 to va 0xd0000000 size: 0x3f000

Clocks: ARM_SYSST: 0x0000 DPLL_CTL: 0x2833 ARM_CKCTL: 0x3000

Clocking rate (xtal/DPLL1/MPU): 12.0/192.0/192.0 MHz

CPU0: D VIVT write-back cache

CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets

Built 1 zonelists

Kernel command line: console=ttyS0,115200n8 noinitrd ip=10.64.42.25:10.64.12.95:10.64.1.1:255.255.0.0:osk:eth0:off root=/dev/nfs rw nfsroot=10.64.12.95:/data/rootfs2.6,nolock mem=32M

Total of 128 interrupts in 4 interrupt banks

OMAP GPIO hardware version 1.0

MUX: initialized M7_1610_GPIO62

PID hash table entries: 256 (order: 8, 4096 bytes)

Console: colour dummy device 80x30

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 32MB = 32MB total

Memory: 29328KB available (2378K code, 481K data, 120K init)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

OMAP DMA hardware version 1

DMA capabilities: 000c0000:00000000:01ff:003f:007f

Initializing OMAP McBSP system

USB: hmc 16, usb0 2 wires

i2c_omap: bus 0 rev2.2 at 100 KHz

tps65010: version 2 May 2005

MUX: initialized N14_1610_UWIRE_CS0

MUX: initialized P15_1610_UWIRE_CS3

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

NetWinder Floating Point Emulator V0.97 (double precision)

OMAP OCPI interconnect driver loaded

Power Management for TI OMAP.

MUX: initialized T20_1610_LOW_PWR

JFFS version 1.0, (C) 1999, 2000 Axis Communications AB

JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered

omapfb: configured for panel osk

omapfb-lcdc: init

MUX: initialized PWL

omapfb-lcdc: Pixel clock divider value is obsolete.

omapfb-lcdc: Try to set pixel_clock to 8000 and pcd to 0 in drivers/video/omap/lcd_osk.c and submit a patch.

Console: switching to colour frame buffer device 30x40

omapfb: initialized vram=153600 pixclock 8000 kHz hfreq 20.1 kHz vfreq 63.3 Hz

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0xfffb0000 (irq = 46) is a ST16654

RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize

loop: loaded (max 8 devices)

PPP generic driver version 2.4.2

smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <[email protected]>

eth0: SMC91C94 (rev 9) at c2852300 IRQ 160 [nowait]

eth0: Ethernet addr: 00:0e:99:02:05:93

i2c /dev entries driver

omapflash.0: Found 1 x16 devices at 0x0 in 16-bit bank

omapflash.0: Found 1 x16 devices at 0x1000000 in 16-bit bank

Intel/Sharp Extended Query Table at 0x0031

Using buffer write method

cfi_cmdset_0001: Erase suspend on write enabled

Creating 4 MTD partitions on "omapflash.0":

0x00000000-0x00020000 : "bootloader"

0x00020000-0x00040000 : "params"

0x00040000-0x00240000 : "kernel"

0x00240000-0x02000000 : "filesystem"

MUX: initialized W11_1610_CF_CD1

MUX: initialized P11_1610_CF_CD2

MUX: initialized R11_1610_CF_IOIS16

MUX: initialized V10_1610_CF_IREQ

MUX: initialized W10_1610_CF_RESET

omap_cf: cs2 on irq 222

usbmon: debugfs is not available

MUX: initialized W8_1610_GPIO9

MUX: initialized W4_USB_HIGHZ

ohci ohci: OMAP OHCI

ohci ohci: new USB bus registered, assigned bus number 1

ohci ohci: irq 38, io mem 0xfffba000

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 3 ports detected

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

mice: PS/2 mouse device common for all mice

OMAP Keypad Driver

input: device omap-keypad is statically allocated, will not register

Please convert to input_allocate_device() or contact [email protected]

NET: Registered protocol family 2

IP route cache hash table entries: 512 (order: -1, 2048 bytes)

TCP established hash table entries: 2048 (order: 1, 8192 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

TCP bic registered

NET: Registered protocol family 1

Disabling unused clock "usb_dc_ck"... done

FIXME: Clock "tc2_ck" seems unused

Disabling unused clock "tc1_ck"... done

Skipping reset check for DSP domain clock "dsptim_ck"

Skipping reset check for DSP domain clock "dspxor_ck"

Skipping reset check for DSP domain clock "dspper_ck"

eth0: link up

IP-Config: Complete:

     device=eth0, addr=10.64.42.25, mask=255.255.0.0, gw=10.64.1.1,

    host=osk, domain=, nis-domain=(none),

    bootserver=10.64.12.95, rootserver=10.64.12.95, rootpath=

Looking up port of RPC 100003/2 on 10.64.12.95

Looking up port of RPC 100005/1 on 10.64.12.95

VFS: Mounted root (nfs filesystem).

Freeing init memory: 120K

init started: BusyBox v1.00-pre8 (2004.03.05-22:18+0000) multi-call binary

******************************************
Starting System Init for OMAP5912OSK
******************************************

Please press Enter to activate this console.

BusyBox v1.00-pre8 (2004.03.05-22:18+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands.

-sh: can't access tty; job control turned off
# *********************************************************************************************************
*********************************************************************************************************

U-Boot 1.1.2 (Oct 26 2005 - 16:18:08)

U-Boot code: 11080000 -> 11096144 BSS: -> 1109A914 RAM Configuration:
Bank #0: 10000000 32 MB
Micron StrataFlash MT28F128J3 device initialized

Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
OMAP5912 OSK # bootm 0x100000 ## Booting image at 00100000 ...
  Image Name:   Linux-2.6.15-rc2-omap1-g0cab20fd
  Image Type:   ARM Linux Kernel Image (uncompressed)
  Data Size:    1475388 Bytes =  1.4 MB

Load Address: 10008000
Entry Point: 10008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................... done, booting the kernel.

Linux version 2.6.15-rc2-omap1-g0cab20fd (root@brahma) (gcc version 3.3.2) #4 Thu Dec 1 17:36:52 IST 2005

CPU: ARM926EJ-Sid(wb) [41069263] revision 3 (ARMv5TEJ)

Machine: TI-OSK

Memory policy: ECC disabled, Data cache writeback

OMAP1611b revision 2 handled as 16xx id: 5b058f7948871d18

SRAM: Mapped pa 0x00020000 to va 0xd0000000 size: 0x3f000

Clocks: ARM_SYSST: 0x0000 DPLL_CTL: 0x2833 ARM_CKCTL: 0x3000

Clocking rate (xtal/DPLL1/MPU): 12.0/192.0/192.0 MHz

CPU0: D VIVT write-back cache

CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets

Built 1 zonelists

Kernel command line: console=ttyS0,115200n8 noinitrd rw ip=dhcp root=/dev/nfs nfsroot=10.64.12.95:/data/rootfs2.6,nolock mem=30M

Total of 128 interrupts in 4 interrupt banks

OMAP GPIO hardware version 1.0

MUX: initialized M7_1610_GPIO62

PID hash table entries: 128 (order: 7, 2048 bytes)

Console: colour dummy device 80x30

Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

Memory: 30MB = 30MB total

Memory: 27192KB available (2536K code, 495K data, 124K init)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

NET: Registered protocol family 16

OMAP DMA hardware version 1

DMA capabilities: 000c0000:00000000:01ff:003f:007f

Initializing OMAP McBSP system

MUX: initialized W4_USB_PUEN

USB: hmc 0, usb0 2 wires (dev)

i2c_omap: bus 0 rev2.2 at 100 KHz

tps65010: version 2 May 2005

MUX: initialized N14_1610_UWIRE_CS0

MUX: initialized P15_1610_UWIRE_CS3

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

NetWinder Floating Point Emulator V0.97 (double precision)

OMAP OCPI interconnect driver loaded

Power Management for TI OMAP.

MUX: initialized T20_1610_LOW_PWR

JFFS version 1.0, (C) 1999, 2000 Axis Communications AB

JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered

omapfb: configured for panel osk

omapfb-lcdc: init

MUX: initialized PWL

omapfb-lcdc: Pixel clock divider value is obsolete.

omapfb-lcdc: Try to set pixel_clock to 8000 and pcd to 0 in drivers/video/omap/lcd_osk.c and submit a patch.

Console: switching to colour frame buffer device 30x40

omapfb: initialized vram=153600 pixclock 8000 kHz hfreq 20.1 kHz vfreq 63.3 Hz

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0xfffb0000 (irq = 46) is a ST16654

RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize

loop: loaded (max 8 devices)

PPP generic driver version 2.4.2

smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <[email protected]>

eth0: SMC91C94 (rev 9) at c2052300 IRQ 160 [nowait]

eth0: Ethernet addr: 00:0e:99:02:05:93

i2c /dev entries driver

omapflash.0: Found 1 x16 devices at 0x0 in 16-bit bank

omapflash.0: Found 1 x16 devices at 0x1000000 in 16-bit bank

Intel/Sharp Extended Query Table at 0x0031

Using buffer write method

cfi_cmdset_0001: Erase suspend on write enabled

Creating 4 MTD partitions on "omapflash.0":

0x00000000-0x00020000 : "bootloader"

0x00020000-0x00040000 : "params"

0x00040000-0x00240000 : "kernel"

0x00240000-0x02000000 : "filesystem"

MUX: initialized W11_1610_CF_CD1

MUX: initialized P11_1610_CF_CD2

MUX: initialized R11_1610_CF_IOIS16

MUX: initialized V10_1610_CF_IREQ

MUX: initialized W10_1610_CF_RESET

omap_cf: cs2 on irq 222

usbmon: debugfs is not available

116x: driver isp116x-hcd, 05 Aug 2005

sl811: driver sl811-hcd, 19 May 2005

usbcore: registered new driver usblp

drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver

Initializing USB Mass Storage driver...

usbcore: registered new driver usb-storage

USB Mass Storage support registered.

usbcore: registered new driver usbhid

drivers/usb/input/hid-core.c: v2.6:USB HID core driver

usbcore: registered new driver asix

usbcore: registered new driver cdc_ether

usbcore: registered new driver net1080

usbcore: registered new driver zaurus

udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)

udc: OMAP UDC rev 3.6

udc: hmc mode 0, integrated transceiver

udc: fifo mode 3, 392 bytes not used

usb0: Ethernet Gadget, version: May Day 2005

usb0: using omap_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep3in-int

usb0: MAC 6e:d7:e8:91:90:93

usb0: HOST MAC 8a:f0:df:c4:0f:b9

usb0: RNDIS ready

mice: PS/2 mouse device common for all mice

OMAP Keypad Driver

input: device omap-keypad is statically allocated, will not register

Please convert to input_allocate_device() or contact [email protected]

NET: Registered protocol family 2

IP route cache hash table entries: 256 (order: -2, 1024 bytes)

TCP established hash table entries: 1024 (order: 0, 4096 bytes)

TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

TCP: Hash tables configured (established 1024 bind 1024)

TCP reno registered

TCP bic registered

NET: Registered protocol family 1

Disabling unused clock "usb_dc_ck"... done

FIXME: Clock "tc2_ck" seems unused

Disabling unused clock "tc1_ck"... done

Skipping reset check for DSP domain clock "dsptim_ck"

Skipping reset check for DSP domain clock "dspxor_ck"

Skipping reset check for DSP domain clock "dspper_ck"

eth0: link up

Sending DHCP requests ., OK

IP-Config: Got DHCP answer from 10.64.2.1, my address is 10.64.12.234

IP-Config: Complete:

     device=eth0, addr=10.64.12.234, mask=255.255.0.0, gw=10.64.1.1,

    host=10.64.12.234, domain=dhcpee.iitd.ac.in, nis-domain=(none),

    bootserver=10.64.2.1, rootserver=10.64.12.95, rootpath=

Looking up port of RPC 100003/2 on 10.64.12.95

Looking up port of RPC 100005/1 on 10.64.12.95

VFS: Mounted root (nfs filesystem).

Freeing init memory: 124K

init started: BusyBox v1.00-pre8 (2004.03.05-22:18+0000) multi-call binary

******************************************
Starting System Init for OMAP5912OSK
******************************************

Please press Enter to activate this console.

BusyBox v1.00-pre8 (2004.03.05-22:18+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands.

-sh: can't access tty; job control turned off
#

------------------------------------------------------------------------

_______________________________________________
Linux-omap-open-source mailing list
[email protected]
http://linux.omap.com/mailman/listinfo/linux-omap-open-source