Skip to contentSkip to conversation

b2c2: make front-ends selectable and include noob option

PATCH NAK Prakash Punnoor 4 participants 10 messages Dec 6, 2005 – Dec 7, 2005 1 message not in the archive

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 b2c2: make front-ends selectable and include noob option

Hi,

this patch probably needs some touch-up but mainly I am sking the dvb guys why don't they do something like this. Current situation:

For my Skystar2 card I am forced to compile in half a dozen front-ends + fw loader - but I only need one front-end driver and no fw loader. Furthermore this crap in the log goes away by throwing unneccessary stuff out:

before:
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 1
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 17
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:03:73:66
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
mt352_read_register: readreg error (reg=127, ret==-121)
b2c2-flexcop: i2c master_xfer failed
i2c_readbytes: i2c read error (addr 0a, err == -121)
b2c2-flexcop: i2c master_xfer failed
lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121)
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
stv0297_readreg: readreg error (reg == 0x80, ret == -22)
b2c2-flexcop: found the vp310 (aka mt312) at i2c address: 0x0e
DVB: registering frontend 0 (Zarlink VP310 DVB-S)...
b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S (old version)' at the 'PCI' bus controlled by a 'FlexCopII' complete

after:
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 1
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 17
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:03:73:66
b2c2-flexcop: found the vp310 (aka mt312) at i2c address: 0x0e
DVB: registering frontend 0 (Zarlink VP310 DVB-S)...
b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S (old version)' at the 'PCI' bus controlled by a 'FlexCopII' complete

Needless to say that my kernel size is a bit smaller and my card still works.

I made the patch trying to follow: http://www.linuxjournal.com/article/5780
by Greg Kroah-Hartman, esp the paragraph "No ifdefs in .c Code". Unfortunately there this is the problem with request_firmware(...) which I needed to ifdef out. Probably someone has a better idea.

I also added an *option* to include every supported front-end, so that noobs don't have to guess around and I guess this was the intention by the dvb devs by selection all frontends by default. I only dislike the missing possibility to deselect unwanted ones. (Is it possible to select this option by default? I don't know much about Kbuild.)

Anyway I asked the dvb guys why the included everything unselectable by default, but I got no response, thus I submit this patch hoping to get more response now.

Of course, this patch only addresses the b2c2 chips. So here it goes, hoping I haven't missed anything:

b2c2/flexcop-fe-tuner.c +0 -0
diff -urd dvb.old/b2c2/flexcop-fe-tuner.c dvb/b2c2/flexcop-fe-tuner.c
@@ -293,8 +293,12 @@
 
 static int flexcop_fe_request_firmware(struct dvb_frontend* fe, const struct 

firmware **fw, char* name)
{
+#ifdef CONFIG_FW_LOADER
struct flexcop_device *fc = fe->dvb->priv; return request_firmware(fw, name, fc->dev);
+#else
+ return -EINVAL;
+#endif
}

static int lgdt3303_pll_set(struct dvb_frontend* fe,

b2c2/Kconfig +14 -3
diff -urd dvb.old/b2c2/Kconfig dvb/b2c2/Kconfig
@@ -1,6 +1,15 @@
 config DVB_B2C2_FLEXCOP
 	tristate "Technisat/B2C2 FlexCopII(b) and FlexCopIII adapters"
 	depends on DVB_CORE
+	help
+	  Support for the digital TV receiver chip made by B2C2 Inc. included in
+	  Technisats PCI cards and USB boxes.
+
+	  Say Y if you own such a device and want to use it.
+
+config DVB_B2C2_FLEXCOP_ALL_FRONTENDS
+	bool "Select all supported front-ends"
+	depends on DVB_B2C2_FLEXCOP
 	select DVB_STV0299
 	select DVB_MT352
 	select DVB_MT312
@@ -9,10 +18,12 @@
 	select DVB_BCM3510
 	select DVB_LGDT330X
 	help
-	  Support for the digital TV receiver chip made by B2C2 Inc. included in
-	  Technisats PCI cards and USB boxes.
+	  Selects all supported front-ends by Technisat/B2C2 driver.
+	  If you don't select this option, you must select the correct
+	  front-end by hand.
+
+	  Say Y if you don't know your front-end.
 
-	  Say Y if you own such a device and want to use it.
 
 config DVB_B2C2_FLEXCOP_PCI
 	tristate "Technisat/B2C2 Air/Sky/Cable2PC PCI"
frontends/bcm3510.h +0 -0
diff -urd dvb.old/frontends/bcm3510.h dvb/frontends/bcm3510.h
@@ -34,7 +34,15 @@
 	int (*request_firmware)(struct dvb_frontend* fe, const struct firmware **fw, 

char* name);
};

+#ifdef CONFIG_DVB_BCM3510
extern struct dvb_frontend* bcm3510_attach(const struct bcm3510_config*
config,
struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* bcm3510_attach(const struct bcm3510_config* config,
+ struct i2c_adapter* i2c)
+{
+ return NULL;
+}
+#endif

#endif

frontends/lgdt330x.h +1 -0
diff -urd dvb.old/frontends/lgdt330x.h dvb/frontends/lgdt330x.h
@@ -53,8 +53,16 @@
 	int clock_polarity_flip;
 };
 
+#ifdef CONFIG_DVB_LGDT330X
 extern struct dvb_frontend* lgdt330x_attach(const struct lgdt330x_config* 

config,
struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* lgdt330x_attach(const struct lgdt330x_config* config,
+ struct i2c_adapter* i2c)
+{
+ return NULL;
+}
+#endif

#endif /* LGDT330X_H */

frontends/mt312.h +0 -0
diff -urd dvb.old/frontends/mt312.h dvb/frontends/mt312.h
@@ -38,10 +38,24 @@
 	int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters* 

params);
};

+#ifdef CONFIG_DVB_MT312
extern struct dvb_frontend* mt312_attach(const struct mt312_config* config,
struct i2c_adapter* i2c);

extern struct dvb_frontend* vp310_attach(const struct mt312_config* config,
struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* mt312_attach(const struct mt312_config* config,
+ struct i2c_adapter* i2c)
+{
+ return NULL;
+}
+
+static inline struct dvb_frontend* vp310_attach(const struct mt312_config* config,
+ struct i2c_adapter* i2c)
+{
+ return NULL;
+}
+#endif

#endif // MT312_H

frontends/mt352.h +0 -0
diff -urd dvb.old/frontends/mt352.h dvb/frontends/mt352.h
@@ -57,9 +57,22 @@
 	int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters* 

params, u8* pllbuf);
};

+#ifdef CONFIG_DVB_MT352
extern struct dvb_frontend* mt352_attach(const struct mt352_config* config,
struct i2c_adapter* i2c);

extern int mt352_write(struct dvb_frontend* fe, u8* ibuf, int ilen);
+#else
+static inline struct dvb_frontend* mt352_attach(const struct mt352_config* config,
+ struct i2c_adapter* i2c)
+{
+ return NULL;
+}
+
+static inline int mt352_write(struct dvb_frontend* fe, u8* ibuf, int ilen) +{
+ return 0;
+}
+#endif

#endif // MT352_H

frontends/nxt2002.h +0 -0
diff -urd dvb.old/frontends/nxt2002.h dvb/frontends/nxt2002.h
@@ -17,7 +17,15 @@
 	int (*request_firmware)(struct dvb_frontend* fe, const struct firmware **fw, 

char* name);
};

+#ifdef CONFIG_DVB_NXT2002
extern struct dvb_frontend* nxt2002_attach(const struct nxt2002_config*
config,
struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* nxt2002_attach(const struct nxt2002_config* config,
+ struct i2c_adapter* i2c)
+{
+ return NULL;
+}
+#endif

#endif // NXT2002_H

frontends/stv0297.h +0 -0
diff -urd dvb.old/frontends/stv0297.h dvb/frontends/stv0297.h
@@ -43,8 +43,21 @@
 	int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters* 

params);
};

+#ifdef CONFIG_DVB_STV0297
extern struct dvb_frontend* stv0297_attach(const struct stv0297_config*
config,
struct i2c_adapter* i2c);
extern int stv0297_enable_plli2c(struct dvb_frontend* fe);
+#else
+static inline struct dvb_frontend* stv0297_attach(const struct stv0297_config* config,
+ struct i2c_adapter* i2c)
+{
+ return NULL;
+}
+
+static inline int stv0297_enable_plli2c(struct dvb_frontend* fe) +{
+ return 0;
+}
+#endif

#endif // STV0297_H

frontends/stv0299.h +0 -0
diff -urd dvb.old/frontends/stv0299.h dvb/frontends/stv0299.h
@@ -93,9 +93,22 @@
 	int (*pll_set)(struct dvb_frontend *fe, struct i2c_adapter *i2c, struct 

dvb_frontend_parameters *params);
};

+#ifdef CONFIG_DVB_STV0299
extern int stv0299_writereg (struct dvb_frontend* fe, u8 reg, u8 data);

extern struct dvb_frontend* stv0299_attach(const struct stv0299_config*
config,
struct i2c_adapter* i2c);
+#else
+static inline int stv0299_writereg (struct dvb_frontend* fe, u8 reg, u8 data) +{
+ return 0;
+}
+
+static inline struct dvb_frontend* stv0299_attach(const struct stv0299_config* config,
+ struct i2c_adapter* i2c)
+{
+ return NULL;
+}
+#endif

#endif // STV0299_H

Signature · 3 lines
(°=                 =°)
//\ Prakash Punnoor /\\
V_/                 \_V
b2c2/flexcop-fe-tuner.c +4 -0
diff -urd dvb.old/b2c2/flexcop-fe-tuner.c dvb/b2c2/flexcop-fe-tuner.c
@@ -293,8 +293,12 @@
 
 static int flexcop_fe_request_firmware(struct dvb_frontend* fe, const struct firmware **fw, char* name)
 {
+#ifdef CONFIG_FW_LOADER
 	struct flexcop_device *fc = fe->dvb->priv;
 	return request_firmware(fw, name, fc->dev);
+#else
+	return -EINVAL;
+#endif
 }
 
 static int lgdt3303_pll_set(struct dvb_frontend* fe,
b2c2/Kconfig +14 -3
diff -urd dvb.old/b2c2/Kconfig dvb/b2c2/Kconfig
@@ -1,6 +1,15 @@
 config DVB_B2C2_FLEXCOP
 	tristate "Technisat/B2C2 FlexCopII(b) and FlexCopIII adapters"
 	depends on DVB_CORE
+	help
+	  Support for the digital TV receiver chip made by B2C2 Inc. included in
+	  Technisats PCI cards and USB boxes.
+
+	  Say Y if you own such a device and want to use it.
+
+config DVB_B2C2_FLEXCOP_ALL_FRONTENDS
+	bool "Select all supported front-ends"
+	depends on DVB_B2C2_FLEXCOP
 	select DVB_STV0299
 	select DVB_MT352
 	select DVB_MT312
@@ -9,10 +18,12 @@
 	select DVB_BCM3510
 	select DVB_LGDT330X
 	help
-	  Support for the digital TV receiver chip made by B2C2 Inc. included in
-	  Technisats PCI cards and USB boxes.
+	  Selects all supported front-ends by Technisat/B2C2 driver.
+	  If you don't select this option, you must select the correct
+	  front-end by hand.
+
+	  Say Y if you don't know your front-end.
 
-	  Say Y if you own such a device and want to use it.
 
 config DVB_B2C2_FLEXCOP_PCI
 	tristate "Technisat/B2C2 Air/Sky/Cable2PC PCI"
frontends/bcm3510.h +8 -0
diff -urd dvb.old/frontends/bcm3510.h dvb/frontends/bcm3510.h
@@ -34,7 +34,15 @@
 	int (*request_firmware)(struct dvb_frontend* fe, const struct firmware **fw, char* name);
 };
 
+#ifdef CONFIG_DVB_BCM3510
 extern struct dvb_frontend* bcm3510_attach(const struct bcm3510_config* config,
 					   struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* bcm3510_attach(const struct bcm3510_config* config,
+						  struct i2c_adapter* i2c)
+{
+	return NULL;
+}
+#endif
 
 #endif
frontends/lgdt330x.h +8 -0
diff -urd dvb.old/frontends/lgdt330x.h dvb/frontends/lgdt330x.h
@@ -53,8 +53,16 @@
 	int clock_polarity_flip;
 };
 
+#ifdef CONFIG_DVB_LGDT330X
 extern struct dvb_frontend* lgdt330x_attach(const struct lgdt330x_config* config,
 					    struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* lgdt330x_attach(const struct lgdt330x_config* config,
+						   struct i2c_adapter* i2c)
+{
+	return NULL;
+}
+#endif
 
 #endif /* LGDT330X_H */
 
frontends/mt312.h +14 -0
diff -urd dvb.old/frontends/mt312.h dvb/frontends/mt312.h
@@ -38,10 +38,24 @@
 	int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters* params);
 };
 
+#ifdef CONFIG_DVB_MT312
 extern struct dvb_frontend* mt312_attach(const struct mt312_config* config,
 					 struct i2c_adapter* i2c);
 
 extern struct dvb_frontend* vp310_attach(const struct mt312_config* config,
 					 struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* mt312_attach(const struct mt312_config* config,
+						struct i2c_adapter* i2c)
+{
+	return NULL;
+}
+
+static inline struct dvb_frontend* vp310_attach(const struct mt312_config* config,
+						struct i2c_adapter* i2c)
+{
+	return NULL;
+}
+#endif
 
 #endif // MT312_H
frontends/mt352.h +13 -0
diff -urd dvb.old/frontends/mt352.h dvb/frontends/mt352.h
@@ -57,9 +57,22 @@
 	int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters* params, u8* pllbuf);
 };
 
+#ifdef CONFIG_DVB_MT352
 extern struct dvb_frontend* mt352_attach(const struct mt352_config* config,
 					 struct i2c_adapter* i2c);
 
 extern int mt352_write(struct dvb_frontend* fe, u8* ibuf, int ilen);
+#else
+static inline struct dvb_frontend* mt352_attach(const struct mt352_config* config,
+						struct i2c_adapter* i2c)
+{
+	return NULL;
+}
+
+static inline int mt352_write(struct dvb_frontend* fe, u8* ibuf, int ilen)
+{
+	return 0;
+}
+#endif
 
 #endif // MT352_H
frontends/nxt2002.h +8 -0
diff -urd dvb.old/frontends/nxt2002.h dvb/frontends/nxt2002.h
@@ -17,7 +17,15 @@
 	int (*request_firmware)(struct dvb_frontend* fe, const struct firmware **fw, char* name);
 };
 
+#ifdef CONFIG_DVB_NXT2002
 extern struct dvb_frontend* nxt2002_attach(const struct nxt2002_config* config,
 					   struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* nxt2002_attach(const struct nxt2002_config* config,
+						  struct i2c_adapter* i2c)
+{
+	return NULL;
+}
+#endif
 
 #endif // NXT2002_H
frontends/stv0297.h +13 -0
diff -urd dvb.old/frontends/stv0297.h dvb/frontends/stv0297.h
@@ -43,8 +43,21 @@
 	int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters* params);
 };
 
+#ifdef CONFIG_DVB_STV0297
 extern struct dvb_frontend* stv0297_attach(const struct stv0297_config* config,
 					   struct i2c_adapter* i2c);
 extern int stv0297_enable_plli2c(struct dvb_frontend* fe);
+#else
+static inline struct dvb_frontend* stv0297_attach(const struct stv0297_config* config,
+						  struct i2c_adapter* i2c)
+{
+	return NULL;
+}
+
+static inline int stv0297_enable_plli2c(struct dvb_frontend* fe)
+{
+	return 0;
+}
+#endif
 
 #endif // STV0297_H
frontends/stv0299.h +13 -0
diff -urd dvb.old/frontends/stv0299.h dvb/frontends/stv0299.h
@@ -93,9 +93,22 @@
 	int (*pll_set)(struct dvb_frontend *fe, struct i2c_adapter *i2c, struct dvb_frontend_parameters *params);
 };
 
+#ifdef CONFIG_DVB_STV0299
 extern int stv0299_writereg (struct dvb_frontend* fe, u8 reg, u8 data);
 
 extern struct dvb_frontend* stv0299_attach(const struct stv0299_config* config,
 					   struct i2c_adapter* i2c);
+#else
+static inline int stv0299_writereg (struct dvb_frontend* fe, u8 reg, u8 data)
+{
+	return 0;
+}
+
+static inline struct dvb_frontend* stv0299_attach(const struct stv0299_config* config,
+						  struct i2c_adapter* i2c)
+{
+	return NULL;
+}
+#endif
 
 #endif // STV0299_H
#1 lore raw

I apologize if you've received this twice. My first message got bounced from LKML... Trying again.

Quoted 312 lines · Prakash Punnoor

Hi,

this patch probably needs some touch-up but mainly I am sking the dvb guys why don't they do something like this. Current situation:

For my Skystar2 card I am forced to compile in half a dozen front-ends + fw loader - but I only need one front-end driver and no fw loader. Furthermore this crap in the log goes away by throwing unneccessary stuff out:

before:
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 1
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 17
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:03:73:66
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
mt352_read_register: readreg error (reg=127, ret==-121)
b2c2-flexcop: i2c master_xfer failed
i2c_readbytes: i2c read error (addr 0a, err == -121)
b2c2-flexcop: i2c master_xfer failed
lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121)
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
stv0297_readreg: readreg error (reg == 0x80, ret == -22)
b2c2-flexcop: found the vp310 (aka mt312) at i2c address: 0x0e
DVB: registering frontend 0 (Zarlink VP310 DVB-S)...
b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S (old version)' at the 'PCI' bus controlled by a 'FlexCopII' complete

after:
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 1
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 17
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:03:73:66
b2c2-flexcop: found the vp310 (aka mt312) at i2c address: 0x0e
DVB: registering frontend 0 (Zarlink VP310 DVB-S)...
b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S (old version)' at the 'PCI' bus controlled by a 'FlexCopII' complete

Needless to say that my kernel size is a bit smaller and my card still works.

I made the patch trying to follow: http://www.linuxjournal.com/article/5780
by Greg Kroah-Hartman, esp the paragraph "No ifdefs in .c Code". Unfortunately there this is the problem with request_firmware(...) which I needed to ifdef out. Probably someone has a better idea.

I also added an *option* to include every supported front-end, so that noobs don't have to guess around and I guess this was the intention by the dvb devs by selection all frontends by default. I only dislike the missing possibility to deselect unwanted ones. (Is it possible to select this option by default? I don't know much about Kbuild.)

Anyway I asked the dvb guys why the included everything unselectable by default, but I got no response, thus I submit this patch hoping to get more response now.

Of course, this patch only addresses the b2c2 chips. So here it goes, hoping I haven't missed anything:

diff -urd dvb.old/b2c2/flexcop-fe-tuner.c dvb/b2c2/flexcop-fe-tuner.c

b2c2/flexcop-fe-tuner.c 2005-12-06 20:29:55.144876736 +0100 renamed from b2c2/flexcop-fe-tuner.c 2005-12-06 19:55:39.060449080 +0100 +4 -0
@@ -293,8 +293,12 @@
 
 static int flexcop_fe_request_firmware(struct dvb_frontend* fe, const struct
 firmware **fw, char* name)
 {
+#ifdef CONFIG_FW_LOADER
        struct flexcop_device *fc = fe->dvb->priv;
        return request_firmware(fw, name, fc->dev);
+#else
+       return -EINVAL;
+#endif
 }
 

static int lgdt3303_pll_set(struct dvb_frontend* fe,
diff -urd dvb.old/b2c2/Kconfig dvb/b2c2/Kconfig

b2c2/Kconfig 2005-12-06 20:36:36.751823200 +0100 renamed from b2c2/Kconfig 2005-12-06 19:55:39.060449080 +0100 +14 -3
@@ -1,6 +1,15 @@
 config DVB_B2C2_FLEXCOP
        tristate "Technisat/B2C2 FlexCopII(b) and FlexCopIII adapters"
        depends on DVB_CORE
+       help
+         Support for the digital TV receiver chip made by B2C2 Inc. included in
+         Technisats PCI cards and USB boxes.
+
+         Say Y if you own such a device and want to use it.
+
+config DVB_B2C2_FLEXCOP_ALL_FRONTENDS
+       bool "Select all supported front-ends"
+       depends on DVB_B2C2_FLEXCOP
        select DVB_STV0299
        select DVB_MT352
        select DVB_MT312
@@ -9,10 +18,12 @@
        select DVB_BCM3510
        select DVB_LGDT330X
        help
-         Support for the digital TV receiver chip made by B2C2 Inc. included in
-         Technisats PCI cards and USB boxes.
+         Selects all supported front-ends by Technisat/B2C2 driver.
+         If you don't select this option, you must select the correct
+         front-end by hand.
+
+         Say Y if you don't know your front-end.
 
-         Say Y if you own such a device and want to use it.
 
 config DVB_B2C2_FLEXCOP_PCI
        tristate "Technisat/B2C2 Air/Sky/Cable2PC PCI"

diff -urd dvb.old/frontends/bcm3510.h dvb/frontends/bcm3510.h

frontends/bcm3510.h 2005-12-06 20:09:37.878929288 +0100 renamed from frontends/bcm3510.h 2005-12-06 19:55:39.445390560 +0100 +3 -0
@@ -34,7 +34,15 @@
        int (*request_firmware)(struct dvb_frontend* fe, const struct firmware **fw,
 char* name);
 };
 
+#ifdef CONFIG_DVB_BCM3510
 extern struct dvb_frontend* bcm3510_attach(const struct bcm3510_config*
 config,
                                           struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* bcm3510_attach(const struct

bcm3510_config* config,

frontends/bcm3510.h 2005-12-06 20:09:37.878929288 +0100 renamed from frontends/bcm3510.h 2005-12-06 19:55:39.445390560 +0100 +5 -0
+                                                 struct i2c_adapter* i2c)
+{
+       return NULL;
+}
+#endif
 
 #endif

diff -urd dvb.old/frontends/lgdt330x.h dvb/frontends/lgdt330x.h

frontends/lgdt330x.h 2005-12-06 20:00:10.309213000 +0100 renamed from frontends/lgdt330x.h 2005-12-06 19:55:39.645360160 +0100 +8 -0
@@ -53,8 +53,16 @@
        int clock_polarity_flip;
 };
 
+#ifdef CONFIG_DVB_LGDT330X
 extern struct dvb_frontend* lgdt330x_attach(const struct lgdt330x_config*
 config,
                                            struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* lgdt330x_attach(const struct
 lgdt330x_config* config,
+                                                  struct i2c_adapter* i2c)
+{
+       return NULL;
+}
+#endif
 

#endif /* LGDT330X_H */

diff -urd dvb.old/frontends/mt312.h dvb/frontends/mt312.h

frontends/mt312.h 2005-12-06 20:04:07.191201464 +0100 renamed from frontends/mt312.h 2005-12-06 19:55:39.503381744 +0100 +9 -0
@@ -38,10 +38,24 @@
        int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters*
 params);
 };
 
+#ifdef CONFIG_DVB_MT312
 extern struct dvb_frontend* mt312_attach(const struct mt312_config* config,
                                         struct i2c_adapter* i2c);
 
 extern struct dvb_frontend* vp310_attach(const struct mt312_config* config,
                                         struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* mt312_attach(const struct mt312_config*
 config,
+                                               struct i2c_adapter* i2c)
+{
+       return NULL;
+}
+
+static inline struct dvb_frontend* vp310_attach(const struct mt312_config*

config,

frontends/mt312.h 2005-12-06 20:04:07.191201464 +0100 renamed from frontends/mt312.h 2005-12-06 19:55:39.503381744 +0100 +5 -0
+                                               struct i2c_adapter* i2c)
+{
+       return NULL;
+}
+#endif
 
 #endif // MT312_H

diff -urd dvb.old/frontends/mt352.h dvb/frontends/mt352.h

frontends/mt352.h 2005-12-06 20:04:21.881968128 +0100 renamed from frontends/mt352.h 2005-12-06 19:55:39.540376120 +0100 +13 -0
@@ -57,9 +57,22 @@
        int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters*
 params, u8* pllbuf);
 };
 
+#ifdef CONFIG_DVB_MT352
 extern struct dvb_frontend* mt352_attach(const struct mt352_config* config,
                                         struct i2c_adapter* i2c);
 
 extern int mt352_write(struct dvb_frontend* fe, u8* ibuf, int ilen);
+#else
+static inline struct dvb_frontend* mt352_attach(const struct mt352_config*
 config,
+                                               struct i2c_adapter* i2c)
+{
+       return NULL;
+}
+
+static inline int mt352_write(struct dvb_frontend* fe, u8* ibuf, int ilen)
+{
+       return 0;
+}
+#endif

#endif // MT352_H
diff -urd dvb.old/frontends/nxt2002.h dvb/frontends/nxt2002.h

frontends/nxt2002.h 2005-12-06 20:08:39.722770368 +0100 renamed from frontends/nxt2002.h 2005-12-06 19:55:39.540376120 +0100 +3 -0
@@ -17,7 +17,15 @@
        int (*request_firmware)(struct dvb_frontend* fe, const struct firmware **fw,
 char* name);
 };
 
+#ifdef CONFIG_DVB_NXT2002
 extern struct dvb_frontend* nxt2002_attach(const struct nxt2002_config*
 config,
                                           struct i2c_adapter* i2c);
+#else
+static inline struct dvb_frontend* nxt2002_attach(const struct

nxt2002_config* config,

frontends/nxt2002.h 2005-12-06 20:08:39.722770368 +0100 renamed from frontends/nxt2002.h 2005-12-06 19:55:39.540376120 +0100 +5 -0
+                                                 struct i2c_adapter* i2c)
+{
+       return NULL;
+}
+#endif
 
 #endif // NXT2002_H

diff -urd dvb.old/frontends/stv0297.h dvb/frontends/stv0297.h

frontends/stv0297.h 2005-12-06 20:06:34.959737232 +0100 renamed from frontends/stv0297.h 2005-12-06 19:55:39.577370496 +0100 +3 -0
@@ -43,8 +43,21 @@
        int (*pll_set)(struct dvb_frontend* fe, struct dvb_frontend_parameters*
 params);
 };
 
+#ifdef CONFIG_DVB_STV0297
 extern struct dvb_frontend* stv0297_attach(const struct stv0297_config*
 config,
                                           struct i2c_adapter* i2c);
 extern int stv0297_enable_plli2c(struct dvb_frontend* fe);
+#else
+static inline struct dvb_frontend* stv0297_attach(const struct

stv0297_config* config,

frontends/stv0297.h 2005-12-06 20:06:34.959737232 +0100 renamed from frontends/stv0297.h 2005-12-06 19:55:39.577370496 +0100 +10 -0
+                                                 struct i2c_adapter* i2c)
+{
+       return NULL;
+}
+
+static inline int stv0297_enable_plli2c(struct dvb_frontend* fe)
+{
+       return 0;
+}
+#endif
 
 #endif // STV0297_H

diff -urd dvb.old/frontends/stv0299.h dvb/frontends/stv0299.h

frontends/stv0299.h 2005-12-06 19:59:45.158036560 +0100 renamed from frontends/stv0299.h 2005-12-06 19:55:39.681354688 +0100 +8 -0
@@ -93,9 +93,22 @@
        int (*pll_set)(struct dvb_frontend *fe, struct i2c_adapter *i2c, struct
 dvb_frontend_parameters *params);
 };
 
+#ifdef CONFIG_DVB_STV0299
 extern int stv0299_writereg (struct dvb_frontend* fe, u8 reg, u8 data);
 
 extern struct dvb_frontend* stv0299_attach(const struct stv0299_config*
 config,
                                           struct i2c_adapter* i2c);
+#else
+static inline int stv0299_writereg (struct dvb_frontend* fe, u8 reg, u8 data)
+{
+       return 0;
+}
+
+static inline struct dvb_frontend* stv0299_attach(const struct

stv0299_config* config,

frontends/stv0299.h 2005-12-06 19:59:45.158036560 +0100 renamed from frontends/stv0299.h 2005-12-06 19:55:39.681354688 +0100 +5 -1
+                                                 struct i2c_adapter* i2c)
+{
+       return NULL;
+}
+#endif
 
 #endif // STV0299_H
 
 
 
 
--
Quoted 6 lines

(°= =°)
//\ Prakash Punnoor /\\
V_/ \_V

NACK.

You are going to run into some problems with this patch... For
instance, What if the user chooses to compile the b2c2-flexcop driver in-kernel, but only compiles the frontend drivers as modules... Then, the frontend support will be built into the flexcop driver, but the module will not yet be available at the time when the kernel is looking for it...

Take a look at what I did to the following files.... You may want to
apply the same method to the flexcop build, although I am beginning to think that this is more trouble that it's worth...

I am considering reverting the frontend selection patch for cx88 and
saa7134 from 2.6.15 , if I hear one more complaint about it...

I will say it publicly -- Johannes originally didn't like this idea,
and now I see why, although my solution seems to be working well, but I had only intended on sending this to -mm ..... It got merged into 2.6.15 too quickly, but luckily it seems to be working well.

Take a look at what I have done to the following files to enable
advanced frontend selection for cx88-dvb and saa7134-dvb :

drivers/media/video/cx88
/Kconfig
drivers/media/video/cx88/Makefile
drivers/media/video/saa7134/Kconfig
drivers/media/video/saa7134/Makefile

If you see above, select all frontends is selected by default,
because this is the desired behavior, and the previous bahevior that everyone is used to.

When that option is disabled, the user is presented with a list of
frontends to choose from... The frontends are selected with the same tristate value of the [cx88,saa7134]-dvb driver ..... ie:

cx88-dvb is M , frontends will be M
cx88-dvb is Y, frontends will be Y

This MUST happen in this exact manner, otherwise you will get
unresolved symbols, and a useless installation.

I'll tell you the truth, I think Johannes is going to ask that I
revert this frontend selection thing.... If he does, I will respect his wishes. Now that v4l and dvb development has merged into a single cvs repository, I believe that we will find new and better ways to accomplish this "frontend selection" goal........

Regards,

Michael Krufky

P.S.: To anyone interested, my regular email service is down right
now.... You can reach me this gmail address. Please cc me on replies to this message, as my gmail account is not subscriber to the linux-dvb-maintainer list. Thank you.

A message that is not in the archive (sent off-list or not yet received): [email protected]

#3 lore raw

Am Dienstag Dezember 6 2005 21:20 schrieb Michael Krufky:

Quoted 8 lines · Prakash Punnoor
Quoted 6 lines

Hi,

this patch probably needs some touch-up but mainly I am sking the dvb guys why
don't they do something like this. Current situation:

Quoted 7 lines

NACK.

You are going to run into some problems with this patch... For instance, What if the user chooses to compile the b2c2-flexcop driver in-kernel, but only compiles the frontend drivers as modules... Then, the frontend support will be built into the flexcop driver, but the module will not yet be available at the time when the kernel is looking for it...

Well, I said it needed touch up. ;-) After all I didn't seriously believe it gets merged in current state (and yes, I didn't think about the module issue, but you're right , of course). But it simply didn't seem like dvb guys are caring about the problem. I once (probably half a year ago already) mailed to linux-dvb and got zero response. That told me everything.

Personally I won't invest more time in perfecting the patch. I just wanted to get some attention to this problem and will use the patch privately for my own happiness...

Thanks for your input.

Signature · 3 lines
(°=                 =°)
//\ Prakash Punnoor /\\
V_/                 \_V
#4 lore raw
Quoted 23 lines · Prakash Punnoor

Am Dienstag Dezember 6 2005 21:20 schrieb Michael Krufky:

Quoted 8 lines · Prakash Punnoor
Quoted 6 lines

Hi,

this patch probably needs some touch-up but mainly I am sking the dvb guys why
don't they do something like this. Current situation:

Quoted 7 lines

NACK.

You are going to run into some problems with this patch... For instance, What if the user chooses to compile the b2c2-flexcop driver in-kernel, but only compiles the frontend drivers as modules... Then, the frontend support will be built into the flexcop driver, but the module will not yet be available at the time when the kernel is looking for it...

Well, I said it needed touch up. ;-) After all I didn't seriously believe it gets merged in current state (and yes, I didn't think about the module issue, but you're right , of course). But it simply didn't seem like dvb guys are caring about the problem. I once (probably half a year ago already) mailed to linux-dvb and got zero response. That told me everything.

Quoted 5 lines

Personally I won't invest more time in perfecting the patch. I just wanted to get some attention to this problem and will use the patch privately for my own happiness...

Thanks for your input.

Okay, that sounds reasonable... I will make it a point to discuss this issue with Johannes, and either

a) revert my frontend selection patch

or

b) apply the same logic that I employed to [cx88,saa7134]-dvb to the other drivers.

Thanks,

Michael

#5 lore raw
In reply to Prakash Punnoor
Quoted 14 lines · Prakash Punnoor

Am Dienstag Dezember 6 2005 21:20 schrieb Michael Krufky:

Quoted 5 lines · Prakash Punnoor
Quoted 3 lines

this patch probably needs some touch-up but mainly I am sking the dvb guys why
don't they do something like this. Current situation:

Quoted 7 lines

NACK.

You are going to run into some problems with this patch... For instance, What if the user chooses to compile the b2c2-flexcop driver in-kernel, but only compiles the frontend drivers as modules... Then, the frontend support will be built into the flexcop driver, but the module will not yet be available at the time when the kernel is looking for it...

Quoted 5 lines

Well, I said it needed touch up. ;-) After all I didn't seriously believe it gets merged in current state (and yes, I didn't think about the module issue, but you're right , of course). But it simply didn't seem like dvb guys are caring about the problem. I once (probably half a year ago already) mailed to linux-dvb and got zero response. That told me everything.

I make it a point to ignore postings which ignore
the recent mailing list history ;-)

This had been discussed on linux-dvb and the consensus was that no one wants to invest time to maintain an #ifdef mess just so that people can save a few KB in their kernel.

Also, most users don't know and don't care what demodulator their card has, the dependency on all of them, plus the implied auto probing saves them some headaches and us a lot of newbie questions.

Quoted 3 lines

Personally I won't invest more time in perfecting the patch. I just wanted to get some attention to this problem and will use the patch privately for my own happiness...

The b2c2-flexcop-pci driver could certainly use some fixing. Your patch just hides the driver problems by deselecting functionality that _you_ don't need.

Johannes

#6 lore raw
Quoted 33 lines · Johannes Stezenbach
Quoted 14 lines · Prakash Punnoor

Am Dienstag Dezember 6 2005 21:20 schrieb Michael Krufky:

Quoted 5 lines · Prakash Punnoor
Quoted 3 lines

this patch probably needs some touch-up but mainly I am sking the dvb guys why
don't they do something like this. Current situation:

Quoted 7 lines

NACK.

You are going to run into some problems with this patch... For instance, What if the user chooses to compile the b2c2-flexcop driver in-kernel, but only compiles the frontend drivers as modules... Then, the frontend support will be built into the flexcop driver, but the module will not yet be available at the time when the kernel is looking for it...

Quoted 5 lines

Well, I said it needed touch up. ;-) After all I didn't seriously believe it gets merged in current state (and yes, I didn't think about the module issue, but you're right , of course). But it simply didn't seem like dvb guys are caring about the problem. I once (probably half a year ago already) mailed to linux-dvb and got zero response. That told me everything.

I make it a point to ignore postings which ignore
the recent mailing list history ;-)

This had been discussed on linux-dvb and the consensus was that no one wants to invest time to maintain an #ifdef mess just so that people can save a few KB in their kernel.

Also, most users don't know and don't care what demodulator their card has, the dependency on all of them, plus the implied auto probing saves them some headaches and us a lot of newbie questions.

Quoted 8 lines
Quoted 3 lines

Personally I won't invest more time in perfecting the patch. I just wanted to get some attention to this problem and will use the patch privately for my own happiness...

The b2c2-flexcop-pci driver could certainly use some fixing. Your patch just hides the driver problems by deselecting functionality that _you_ don't need.

Johannes -

If you approve of the method that I used to implement compile-time frontend selection in cx88-dvb and saa7134-dvb, then I would be happy to implement this into the flexcop driver as well. I understand why developers might not want to invest the time into this, but I see the benefits to it, and I am willing to work on it. Of course, this wouldnt be sent to the kernel until 2.6.16 (or maybe 2.6.17)

I have the bcm3510-based board in my possesion right now, and both the nxt2002 and lgdt3303 versions are in the mail to me as I type this email. (I plan to use the nxt2002 version to test and fix the nxt200x driver for this use.)

OTOH, if there are other reasons to stay away from this idea, say the word, and I'll send a revert patch to Andrew for the cx88 and saa7134 stuff... It is working well -- Gene reported a bug and I fixed it, already in Linus' tree.

What do you think?

-Michael

#7 lore raw
Quoted 40 lines · Michael Krufky
Quoted 19 lines · Johannes Stezenbach
Quoted 5 lines · Prakash Punnoor

Well, I said it needed touch up. ;-) After all I didn't seriously believe it gets merged in current state (and yes, I didn't think about the module issue, but you're right , of course). But it simply didn't seem like dvb guys are caring about the problem. I once (probably half a year ago already) mailed to linux-dvb and got zero response. That told me everything.

I make it a point to ignore postings which ignore
the recent mailing list history ;-)

This had been discussed on linux-dvb and the consensus was that no one wants to invest time to maintain an #ifdef mess just so that people can save a few KB in their kernel.

Also, most users don't know and don't care what demodulator their card has, the dependency on all of them, plus the implied auto probing saves them some headaches and us a lot of newbie questions.

Quoted 7 lines
Quoted 3 lines

Personally I won't invest more time in perfecting the patch. I just wanted to get some attention to this problem and will use the patch privately for my own happiness...

The b2c2-flexcop-pci driver could certainly use some fixing. Your patch just hides the driver problems by deselecting functionality that _you_ don't need.

If you approve of the method that I used to implement compile-time frontend selection in cx88-dvb and saa7134-dvb, then I would be happy to implement this into the flexcop driver as well. I understand why developers might not want to invest the time into this, but I see the benefits to it, and I am willing to work on it. Of course, this wouldnt be sent to the kernel until 2.6.16 (or maybe 2.6.17)

I have the bcm3510-based board in my possesion right now, and both the nxt2002 and lgdt3303 versions are in the mail to me as I type this email. (I plan to use the nxt2002 version to test and fix the nxt200x driver for this use.)

Quoted 6 lines

OTOH, if there are other reasons to stay away from this idea, say the word, and I'll send a revert patch to Andrew for the cx88 and saa7134 stuff... It is working well -- Gene reported a bug and I fixed it, already in Linus' tree.

What do you think?

I think b2c2-flexcop-pci uses a 240K dma buffer, whether you save a few K in demodulator code doesn't mean much. The saved memory will be similarly unnoticable to the user as if you would go and scatter #ifdefs all over tuner-simple.c.

But I'm neither the author nor the maintainer of the b2c2-flexcop driver, you better ask Patrick if he likes it.

Johannes

#8 lore raw

Hi,

Quoted 7 lines · Johannes Stezenbach

I think b2c2-flexcop-pci uses a 240K dma buffer, whether you save a few K in demodulator code doesn't mean much. The saved memory will be similarly unnoticable to the user as if you would go and scatter #ifdefs all over tuner-simple.c.

But I'm neither the author nor the maintainer of the b2c2-flexcop driver, you better ask Patrick if he likes it.

There will be at least two new devices in the future, which again will need (at least) two new demod(and maybe tuner)-modules.

Prakash, if it is just the i2c_xfer failed, that could be easily turned into a debug-message, but I rather have these as errors, because they are.

I don't see the need for the ifdef - on the contrary: the number of people asking for which demod they shall load dropped significantly after FE_REFACTORING starting one year ago - now reintroducing that again is not a good idea, IMO.

best regards,
Patrick.

--
Mail: [email protected]
WWW: http://www.wi-bw.tfh-wildau.de/~pboettch/

#9 lore raw

Am Mittwoch Dezember 7 2005 08:56 schrieb Patrick Boettcher:

Quoted 8 lines

Hi,

Quoted 5 lines · Johannes Stezenbach

I think b2c2-flexcop-pci uses a 240K dma buffer, whether you save a few K in demodulator code doesn't mean much. The saved memory will be similarly unnoticable to the user as if you would go and scatter #ifdefs all over tuner-simple.c.

Quoted 8 lines
Quoted 2 lines

But I'm neither the author nor the maintainer of the b2c2-flexcop driver, you better ask Patrick if he likes it.

There will be at least two new devices in the future, which again will need (at least) two new demod(and maybe tuner)-modules.

Prakash, if it is just the i2c_xfer failed, that could be easily turned into a debug-message, but I rather have these as errors, because they are.

Well aren't these expected errors? You want to attach an non-existent front-end and the driver finds out it isn't there? IMHO it doesn't look very professional if some strange errors are scattered in the log. I think if you don't find *any* front-end there should be perhaps an error or note to the user, but not because half a dozen of front-ends drivers can't find the hw. At least please make the errors verbose and not cryptical, if you really want them.

If these errors are not expected, they have been here since months and probably should have been fixed. But I think I remember someone saying that they are expected once I reported them...

Quoted 4 lines

I don't see the need for the ifdef - on the contrary: the number of people asking for which demod they shall load dropped significantly after FE_REFACTORING starting one year ago - now reintroducing that again is not a good idea, IMO.

Well, I got twice annoyed by missing reverse dependecies introduced by new front-ends. Once the fw loader and once the new lgt330x(?) front-end. If new front-ends wouldn't go in automatically as rev dependency this wouldn't break for me (and everyone alse using b2c2 in general and not only the new frontends), which is another reason, if you don't care about the bit of code saving.

I really don't see the big problem of the ifdefs as the are in the *header* files as it is just checking whether something is in or not - as the user selected thus emulating that a probe for a front-end failed... If the .c file is coded properly there is no chance of breaking - otherwise you'd have the same problem with the unpatched source (leaving the module problem out for now). (Yes, I know ifdefs in the code as such are bad, but I noted that in conjunction with the fw loader, which was the only "dirty" ifdef.)

And as I said I added an *option* for unsure users to include all supported front-ends, which is another one of your arguments. Selecting it by default (I don't know how to do this) would be what you want then. Wouldn't this make all happy (if Michael additionally fixes the module stuff)?

bye,

Signature · 3 lines
(°=                 =°)
//\ Prakash Punnoor /\\
V_/                 \_V
#10 lore raw
In reply to Johannes Stezenbach

Am Dienstag Dezember 6 2005 22:56 schrieb Johannes Stezenbach:

Quoted 8 lines · Prakash Punnoor
Quoted 6 lines

Well, I said it needed touch up. ;-) After all I didn't seriously believe it gets merged in current state (and yes, I didn't think about the module issue, but you're right , of course). But it simply didn't seem like dvb guys are caring about the problem. I once (probably half a year ago already) mailed to linux-dvb and got zero response. That told me everything.

Quoted 6 lines

I make it a point to ignore postings which ignore
the recent mailing list history ;-)

This had been discussed on linux-dvb and the consensus was that no one wants to invest time to maintain an #ifdef mess just so that people can save a few KB in their kernel.

A short "search the list" note would have been enough, then. I think I followed the list, but probably skipped the messages, as the subject probably seemed like something else.

Quoted 4 lines

Also, most users don't know and don't care what demodulator their card has, the dependency on all of them, plus the implied auto probing saves them some headaches and us a lot of newbie questions.

Well, could you be so nice and at least turn that xfer transfer errors and similar off? I guess that should be debugging output, but only printed when you actually want debugging and shouldn't be default behaviour. Does't this confuse users? It at least always draws my attention...

bye,

Signature · 3 lines
(°=                 =°)
//\ Prakash Punnoor /\\
V_/                 \_V