Skip to contentSkip to conversation

No Coax digital out with SB Live! and 2.6.15

DISCUSSION Tino Keitel 2 participants 6 messages Jan 3, 2006 – Jan 6, 2006

lore
Share & tools
lore
#0 lore raw

Hi folks,

since I upgraded to 2.6.15, the Coax digital output of my SB Live! stays silent. Analog output works. After reverting to 2.6.14.3 the digital output works again. Does anyone have a solution for this or at least the same problem?

Regards,
Tino

#1 lore raw
Quoted 6 lines · Tino Keitel

Hi folks,

since I upgraded to 2.6.15, the Coax digital output of my SB Live! stays silent. Analog output works. After reverting to 2.6.14.3 the digital output works again. Does anyone have a solution for this or at least the same problem?

I just tried alsa-driver 1.0.11-rc2 and now the digital out works again.

Regards,
Tino

#2 lore raw
Quoted 9 lines · Tino Keitel
Quoted 6 lines · Tino Keitel

Hi folks,

since I upgraded to 2.6.15, the Coax digital output of my SB Live! stays silent. Analog output works. After reverting to 2.6.14.3 the digital output works again. Does anyone have a solution for this or at least the same problem?

I just tried alsa-driver 1.0.11-rc2 and now the digital out works again.

alsa-driver 1.0.10 works, too.

Regards,
Tino

#3 lore raw
Quoted 4 lines · Tino Keitel
Quoted 3 lines · Tino Keitel
Quoted 2 lines · Tino Keitel

Hi folks,

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines

since I upgraded to 2.6.15, the Coax digital output of my SB Live! stays silent. Analog output works. After reverting to 2.6.14.3 the digital output works again. Does anyone have a solution for this or at least the same problem?

I just tried alsa-driver 1.0.11-rc2 and now the digital out works again.

alsa-driver 1.0.10 works, too.

Are you sure it was not a mixer settings issue?

If you can confirm that this is a regression try to narrow it down by code inspection or binary search by date with ALSA CVS it can be fixed for 2.6.15.x.

Lee

#4 lore raw
Quoted 12 lines · Lee Revell
Quoted 11 lines · Tino Keitel
Quoted 9 lines · Tino Keitel
Quoted 6 lines · Tino Keitel

Hi folks,

since I upgraded to 2.6.15, the Coax digital output of my SB Live! stays silent. Analog output works. After reverting to 2.6.14.3 the digital output works again. Does anyone have a solution for this or at least the same problem?

I just tried alsa-driver 1.0.11-rc2 and now the digital out works again.

Quoted 7 lines
Quoted 1 line

alsa-driver 1.0.10 works, too.

Are you sure it was not a mixer settings issue?

If you can confirm that this is a regression try to narrow it down by code inspection or binary search by date with ALSA CVS it can be fixed for 2.6.15.x.

I booted with the 2.6.15 driver and got a silent digital out, like reported. The headphone which is plugged into the analog output gives sound.

If I load the 1.0.10 driver, sound works in xmms. If I unload it and reload the original 2.6.15 driver, sound still works. If I reboot with the original 2.6.15 driver, the digital out is silent again, while the analog output works.

However, if I now chose a specific output device in xmms, hw:0,2, instead of the default device, digital out gives sound. With the 1.0.10 driver, this hw:0,2 device stays completely silent (digital and analog). With this version, the hw:0,0 device (which seems to be the default) gives analog and digital sound.

So IMHO this mixup of the devices is a regression, since it breaks existing setups and is also fixed in newer versions. It would be nice the see a fix for this in 2.6.15.x.

Regards,
Tino

#5 lore raw

On Fri, Jan 06, 2006 at 01:09:21 +0100, Tino Keitel wrote:

[...]

Quoted 9 lines

I booted with the 2.6.15 driver and got a silent digital out, like reported. The headphone which is plugged into the analog output gives sound.

If I load the 1.0.10 driver, sound works in xmms. If I unload it and reload the original 2.6.15 driver, sound still works. If I reboot with the original 2.6.15 driver, the digital out is silent again, while the analog output works.

Quoted 5 lines

However, if I now chose a specific output device in xmms, hw:0,2, instead of the default device, digital out gives sound. With the 1.0.10 driver, this hw:0,2 device stays completely silent (digital and analog). With this version, the hw:0,0 device (which seems to be the default) gives analog and digital sound.

The solution looks more simple: just removing and reloading the original snd-emu10k1 module reorders the devices so that the default device gives sound on the digital output. The driver is blacklisted in udev and loaded at boot time in /etc/modules, so the module-init-tools initscript will load them. However, I have no idea why it behaves different if loaded at boot time than when reloaded later.

Regards,
Tino