Skip to contentSkip to conversation

USBATM: summary

PATCH In review Duncan Sands 3 participants 19 messages Jan 12, 2006 – Aug 18, 2006

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

cover USBATM: summary

Hi Greg, here are some fixes and improvements to the USB ATM modem drivers, in thirteen patches:

01: trivial modifications (formatting, changes to variable names, comments, log level changes, printk rate limiting).

02: have minidrivers tell the core about special requirements using a flags field.

03: remove the unused .owner field in struct usbatm_driver.

04: use kzalloc rather than kmalloc + memset.

05: make xusbatm useable.

06: sternly tell open connections that the game is up when the modem is disconnected.

07: return the correct error code when out of memory.

08: use dev_kfree_skb_any rather than dev_kfree_skb.

09: specify buffer sizes in bytes, rather than in ATM cells.

10: add mechanism for turning on isochronous urb support.

11: remove the assumption that incoming urbs contain complete ATM cells.

12: bump some version numbers.

13: EILSEQ hack needed by the ueagle.

All the best,

Duncan.

#1 lore raw

PATCH 1/13 USBATM: trivial modifications

Formatting, changes to variable names, comments, log level changes, printk rate limiting.

cxacru.c +34 -35
Index: kernel/cxacru.c
===================================================================
@@ -352,7 +352,6 @@
 		struct atm_dev *atm_dev)
 {
 	struct cxacru_data *instance = usbatm_instance->driver_data;
-	struct device *dev = &usbatm_instance->usb_intf->dev;
 	/*
 	struct atm_dev *atm_dev = usbatm_instance->atm_dev;
 	*/
@@ -364,14 +363,14 @@
 	ret = cxacru_cm(instance, CM_REQUEST_CARD_GET_MAC_ADDRESS, NULL, 0,
 			atm_dev->esi, sizeof(atm_dev->esi));
 	if (ret < 0) {
-		dev_err(dev, "cxacru_atm_start: CARD_GET_MAC_ADDRESS returned %d\n", ret);
+		atm_err(usbatm_instance, "cxacru_atm_start: CARD_GET_MAC_ADDRESS returned %d\n", ret);
 		return ret;
 	}
 
 	/* start ADSL */
 	ret = cxacru_cm(instance, CM_REQUEST_CHIP_ADSL_LINE_START, NULL, 0, NULL, 0);
 	if (ret < 0) {
-		dev_err(dev, "cxacru_atm_start: CHIP_ADSL_LINE_START returned %d\n", ret);
+		atm_err(usbatm_instance, "cxacru_atm_start: CHIP_ADSL_LINE_START returned %d\n", ret);
 		return ret;
 	}
 
@@ -383,13 +382,13 @@
 static void cxacru_poll_status(struct cxacru_data *instance)
 {
 	u32 buf[CXINF_MAX] = {};
-	struct device *dev = &instance->usbatm->usb_intf->dev;
-	struct atm_dev *atm_dev = instance->usbatm->atm_dev;
+	struct usbatm_data *usbatm = instance->usbatm;
+	struct atm_dev *atm_dev = usbatm->atm_dev;
 	int ret;
 
 	ret = cxacru_cm_get_array(instance, CM_REQUEST_CARD_INFO_GET, buf, CXINF_MAX);
 	if (ret < 0) {
-		dev_warn(dev, "poll status: error %d\n", ret);
+		atm_warn(usbatm, "poll status: error %d\n", ret);
 		goto reschedule;
 	}
 
@@ -400,50 +399,50 @@
 	switch (instance->line_status) {
 	case 0:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: down\n");
+		atm_info(usbatm, "ADSL line: down\n");
 		break;
 
 	case 1:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: attemtping to activate\n");
+		atm_info(usbatm, "ADSL line: attempting to activate\n");
 		break;
 
 	case 2:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: training\n");
+		atm_info(usbatm, "ADSL line: training\n");
 		break;
 
 	case 3:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: channel analysis\n");
+		atm_info(usbatm, "ADSL line: channel analysis\n");
 		break;
 
 	case 4:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: exchange\n");
+		atm_info(usbatm, "ADSL line: exchange\n");
 		break;
 
 	case 5:
 		atm_dev->link_rate = buf[CXINF_DOWNSTREAM_RATE] * 1000 / 424;
 		atm_dev->signal = ATM_PHY_SIG_FOUND;
 
-		dev_info(dev, "ADSL line: up (%d kb/s down | %d kb/s up)\n",
+		atm_info(usbatm, "ADSL line: up (%d kb/s down | %d kb/s up)\n",
 		     buf[CXINF_DOWNSTREAM_RATE], buf[CXINF_UPSTREAM_RATE]);
 		break;
 
 	case 6:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: waiting\n");
+		atm_info(usbatm, "ADSL line: waiting\n");
 		break;
 
 	case 7:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: initializing\n");
+		atm_info(usbatm, "ADSL line: initializing\n");
 		break;
 
 	default:
 		atm_dev->signal = ATM_PHY_SIG_UNKNOWN;
-		dev_info(dev, "Unknown line state %02x\n", instance->line_status);
+		atm_info(usbatm, "Unknown line state %02x\n", instance->line_status);
 		break;
 	}
 reschedule:
@@ -504,8 +503,8 @@
 {
 	int ret;
 	int off;
-	struct usb_device *usb_dev = instance->usbatm->usb_dev;
-	struct device *dev = &instance->usbatm->usb_intf->dev;
+	struct usbatm_data *usbatm = instance->usbatm;
+	struct usb_device *usb_dev = usbatm->usb_dev;
 	u16 signature[] = { usb_dev->descriptor.idVendor, usb_dev->descriptor.idProduct };
 	u32 val;
 
@@ -515,7 +514,7 @@
 	val = cpu_to_le32(instance->modem_type->pll_f_clk);
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, PLLFCLK_ADDR, (u8 *) &val, 4);
 	if (ret) {
-		dev_err(dev, "FirmwarePllFClkValue failed: %d\n", ret);
+		usb_err(usbatm, "FirmwarePllFClkValue failed: %d\n", ret);
 		return;
 	}
 
@@ -523,7 +522,7 @@
 	val = cpu_to_le32(instance->modem_type->pll_b_clk);
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, PLLBCLK_ADDR, (u8 *) &val, 4);
 	if (ret) {
-		dev_err(dev, "FirmwarePllBClkValue failed: %d\n", ret);
+		usb_err(usbatm, "FirmwarePllBClkValue failed: %d\n", ret);
 		return;
 	}
 
@@ -531,14 +530,14 @@
 	val = cpu_to_le32(SDRAM_ENA);
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, SDRAMEN_ADDR, (u8 *) &val, 4);
 	if (ret) {
-		dev_err(dev, "Enable SDRAM failed: %d\n", ret);
+		usb_err(usbatm, "Enable SDRAM failed: %d\n", ret);
 		return;
 	}
 
 	/* Firmware */
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, FW_ADDR, fw->data, fw->size);
 	if (ret) {
-		dev_err(dev, "Firmware upload failed: %d\n", ret);
+		usb_err(usbatm, "Firmware upload failed: %d\n", ret);
 		return;
 	}
 
@@ -546,7 +545,7 @@
 	if (instance->modem_type->boot_rom_patch) {
 		ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, BR_ADDR, bp->data, bp->size);
 		if (ret) {
-			dev_err(dev, "Boot ROM patching failed: %d\n", ret);
+			usb_err(usbatm, "Boot ROM patching failed: %d\n", ret);
 			return;
 		}
 	}
@@ -554,7 +553,7 @@
 	/* Signature */
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, SIG_ADDR, (u8 *) signature, 4);
 	if (ret) {
-		dev_err(dev, "Signature storing failed: %d\n", ret);
+		usb_err(usbatm, "Signature storing failed: %d\n", ret);
 		return;
 	}
 
@@ -566,7 +565,7 @@
 		ret = cxacru_fw(usb_dev, FW_GOTO_MEM, 0x0, 0x0, FW_ADDR, NULL, 0);
 	}
 	if (ret) {
-		dev_err(dev, "Passing control to firmware failed: %d\n", ret);
+		usb_err(usbatm, "Passing control to firmware failed: %d\n", ret);
 		return;
 	}
 
@@ -580,7 +579,7 @@
 
 	ret = cxacru_cm(instance, CM_REQUEST_CARD_GET_STATUS, NULL, 0, NULL, 0);
 	if (ret < 0) {
-		dev_err(dev, "modem failed to initialize: %d\n", ret);
+		usb_err(usbatm, "modem failed to initialize: %d\n", ret);
 		return;
 	}
 
@@ -597,7 +596,7 @@
 			ret = cxacru_cm(instance, CM_REQUEST_CARD_DATA_SET,
 					(u8 *) buf, len, NULL, 0);
 			if (ret < 0) {
-				dev_err(dev, "load config data failed: %d\n", ret);
+				usb_err(usbatm, "load config data failed: %d\n", ret);
 				return;
 			}
 		}
@@ -608,18 +607,19 @@
 static int cxacru_find_firmware(struct cxacru_data *instance,
 				char* phase, const struct firmware **fw_p)
 {
-	struct device *dev = &instance->usbatm->usb_intf->dev;
+	struct usbatm_data *usbatm = instance->usbatm;
+	struct device *dev = &usbatm->usb_intf->dev;
 	char buf[16];
 
 	sprintf(buf, "cxacru-%s.bin", phase);
 	dbg("cxacru_find_firmware: looking for %s", buf);
 
 	if (request_firmware(fw_p, buf, dev)) {
-		dev_dbg(dev, "no stage %s firmware found\n", phase);
+		usb_dbg(usbatm, "no stage %s firmware found\n", phase);
 		return -ENOENT;
 	}
 
-	dev_info(dev, "found firmware %s\n", buf);
+	usb_info(usbatm, "found firmware %s\n", buf);
 
 	return 0;
 }
@@ -627,20 +627,19 @@
 static int cxacru_heavy_init(struct usbatm_data *usbatm_instance,
 			     struct usb_interface *usb_intf)
 {
-	struct device *dev = &usbatm_instance->usb_intf->dev;
 	const struct firmware *fw, *bp, *cf;
 	struct cxacru_data *instance = usbatm_instance->driver_data;
 
 	int ret = cxacru_find_firmware(instance, "fw", &fw);
 	if (ret) {
-		dev_warn(dev, "firmware (cxacru-fw.bin) unavailable (hotplug misconfiguration?)\n");
+		usb_warn(usbatm_instance, "firmware (cxacru-fw.bin) unavailable (system misconfigured?)\n");
 		return ret;
 	}
 
 	if (instance->modem_type->boot_rom_patch) {
 		ret = cxacru_find_firmware(instance, "bp", &bp);
 		if (ret) {
-			dev_warn(dev, "boot ROM patch (cxacru-bp.bin) unavailable (hotplug misconfiguration?)\n");
+			usb_warn(usbatm_instance, "boot ROM patch (cxacru-bp.bin) unavailable (system misconfigured?)\n");
 			release_firmware(fw);
 			return ret;
 		}
@@ -787,12 +786,12 @@
 	{ /* V = Conexant			P = ADSL modem (Hasbani project)	*/
 		USB_DEVICE(0x0572, 0xcb00),	.driver_info = (unsigned long) &cxacru_cb00
 	},
-	{ /* V = Conexant             P = ADSL modem (Well PTI-800 */
-		USB_DEVICE(0x0572, 0xcb02),	.driver_info = (unsigned long) &cxacru_cb00
-	},
 	{ /* V = Conexant			P = ADSL modem				*/
 		USB_DEVICE(0x0572, 0xcb01),	.driver_info = (unsigned long) &cxacru_cb00
 	},
+	{ /* V = Conexant			P = ADSL modem (Well PTI-800) */
+		USB_DEVICE(0x0572, 0xcb02),	.driver_info = (unsigned long) &cxacru_cb00
+	},
 	{ /* V = Conexant			P = ADSL modem				*/
 		USB_DEVICE(0x0572, 0xcb06),	.driver_info = (unsigned long) &cxacru_cb00
 	},
speedtch.c +30 -23

165 lines not on this page · raw message

usbatm.c +60 -41

291 lines not on this page · raw message

usbatm.h +17 -8
Index: kernel/usbatm.h
===================================================================
@@ -24,22 +24,21 @@
 #ifndef	_USBATM_H_
 #define	_USBATM_H_
 
-#include <linux/config.h>
-
-/*
-#define VERBOSE_DEBUG
-*/
-
 #include <asm/semaphore.h>
 #include <linux/atm.h>
 #include <linux/atmdev.h>
 #include <linux/completion.h>
 #include <linux/device.h>
+#include <linux/kernel.h>
 #include <linux/kref.h>
 #include <linux/list.h>
 #include <linux/stringify.h>
 #include <linux/usb.h>
 
+/*
+#define VERBOSE_DEBUG
+*/
+
 #ifdef DEBUG
 #define UDSL_ASSERT(x)	BUG_ON(!(x))
 #else
@@ -52,8 +51,13 @@
 	dev_info(&(instance)->usb_intf->dev , format , ## arg)
 #define usb_warn(instance, format, arg...)	\
 	dev_warn(&(instance)->usb_intf->dev , format , ## arg)
+#ifdef DEBUG
+#define usb_dbg(instance, format, arg...)	\
+        dev_printk(KERN_DEBUG , &(instance)->usb_intf->dev , format , ## arg)
+#else
 #define usb_dbg(instance, format, arg...)	\
-	dev_dbg(&(instance)->usb_intf->dev , format , ## arg)
+	do {} while (0)
+#endif
 
 /* FIXME: move to dev_* once ATM is driver model aware */
 #define atm_printk(level, instance, format, arg...)	\
@@ -69,9 +73,14 @@
 #ifdef DEBUG
 #define atm_dbg(instance, format, arg...)	\
 	atm_printk(KERN_DEBUG, instance , format , ## arg)
+#define atm_rldbg(instance, format, arg...)	\
+	if (printk_ratelimit())				\
+		atm_printk(KERN_DEBUG, instance , format , ## arg)
 #else
 #define atm_dbg(instance, format, arg...)	\
 	do {} while (0)
+#define atm_rldbg(instance, format, arg...)	\
+	do {} while (0)
 #endif
 
 
@@ -171,7 +180,7 @@
 	struct usbatm_channel tx_channel;
 
 	struct sk_buff_head sndqueue;
-	struct sk_buff *current_skb;			/* being emptied */
+	struct sk_buff *current_skb;	/* being emptied */
 
 	struct urb *urbs[0];
 };
xusbatm.c +12 -11
Index: kernel/xusbatm.c
===================================================================
@@ -61,7 +61,7 @@
 	return 0;
 }
 
-static int xusbatm_bind(struct usbatm_data *usbatm_instance,
+static int xusbatm_bind(struct usbatm_data *usbatm,
 			struct usb_interface *intf, const struct usb_device_id *id,
 			int *need_heavy_init)
 {
@@ -72,14 +72,14 @@
 	u8 searched_ep = rx_ep_present ? tx_endpoint[drv_ix] : rx_endpoint[drv_ix];
 	int i, ret;
 
-	usb_dbg(usbatm_instance, "%s: binding driver %d: vendor %#x product %#x"
-		" rx: ep %#x padd %d tx: ep %#x padd %d\n",
+	usb_dbg(usbatm, "%s: binding driver %d: vendor %04x product %04x"
+		" rx: ep %02x padd %d tx: ep %02x padd %d\n",
 		__func__, drv_ix, vendor[drv_ix], product[drv_ix],
 		rx_endpoint[drv_ix], rx_padding[drv_ix],
 		tx_endpoint[drv_ix], tx_padding[drv_ix]);
 
 	if (!rx_ep_present && !tx_ep_present) {
-		usb_dbg(usbatm_instance, "%s: intf #%d has neither rx (%#x) nor tx (%#x) endpoint\n",
+		usb_dbg(usbatm, "%s: intf #%d has neither rx (%#x) nor tx (%#x) endpoint\n",
 			__func__, intf->altsetting->desc.bInterfaceNumber,
 			rx_endpoint[drv_ix], tx_endpoint[drv_ix]);
 		return -ENODEV;
@@ -93,25 +93,26 @@
 
 		if (cur_if != intf && usb_intf_has_ep(cur_if, searched_ep)) {
 			ret = usb_driver_claim_interface(&xusbatm_usb_driver,
-							 cur_if, usbatm_instance);
+							 cur_if, usbatm);
 			if (!ret)
-				usb_err(usbatm_instance, "%s: failed to claim interface #%d (%d)\n",
+				usb_err(usbatm, "%s: failed to claim interface #%d (%d)\n",
 					__func__, cur_if->altsetting->desc.bInterfaceNumber, ret);
 			return ret;
 		}
 	}
 
-	usb_err(usbatm_instance, "%s: no interface has endpoint %#x\n",
+	usb_err(usbatm, "%s: no interface has endpoint %#x\n",
 		__func__, searched_ep);
 	return -ENODEV;
 }
 
-static void xusbatm_unbind(struct usbatm_data *usbatm_instance,
+static void xusbatm_unbind(struct usbatm_data *usbatm,
 			   struct usb_interface *intf)
 {
 	struct usb_device *usb_dev = interface_to_usbdev(intf);
 	int i;
-	usb_dbg(usbatm_instance, "%s entered\n", __func__);
+
+	usb_dbg(usbatm, "%s entered\n", __func__);
 
 	for(i = 0; i < usb_dev->actconfig->desc.bNumInterfaces; i++) {
 		struct usb_interface *cur_if = usb_dev->actconfig->interface[i];
@@ -120,10 +121,10 @@
 	}
 }
 
-static int xusbatm_atm_start(struct usbatm_data *usbatm_instance,
+static int xusbatm_atm_start(struct usbatm_data *usbatm,
 			     struct atm_dev *atm_dev)
 {
-	atm_dbg(usbatm_instance, "%s entered\n", __func__);
+	atm_dbg(usbatm, "%s entered\n", __func__);
 
 	/* use random MAC as we've no way to get it from the device */
 	random_ether_addr(atm_dev->esi);
#2 lore raw

Re: [PATCH 01/13] USBATM: trivial modifications

Sorry, it wasn't a -p1 patch (I should really automate this).

drivers/usb/atm/cxacru.c renamed from drivers/usb/atm.orig/cxacru.c +34 -35
diff -x '*.orig' -x '*.base' -u -r Linux/drivers/usb/atm.orig/cxacru.c Linux/drivers/usb/atm/cxacru.c
@@ -352,7 +352,6 @@
 		struct atm_dev *atm_dev)
 {
 	struct cxacru_data *instance = usbatm_instance->driver_data;
-	struct device *dev = &usbatm_instance->usb_intf->dev;
 	/*
 	struct atm_dev *atm_dev = usbatm_instance->atm_dev;
 	*/
@@ -364,14 +363,14 @@
 	ret = cxacru_cm(instance, CM_REQUEST_CARD_GET_MAC_ADDRESS, NULL, 0,
 			atm_dev->esi, sizeof(atm_dev->esi));
 	if (ret < 0) {
-		dev_err(dev, "cxacru_atm_start: CARD_GET_MAC_ADDRESS returned %d\n", ret);
+		atm_err(usbatm_instance, "cxacru_atm_start: CARD_GET_MAC_ADDRESS returned %d\n", ret);
 		return ret;
 	}
 
 	/* start ADSL */
 	ret = cxacru_cm(instance, CM_REQUEST_CHIP_ADSL_LINE_START, NULL, 0, NULL, 0);
 	if (ret < 0) {
-		dev_err(dev, "cxacru_atm_start: CHIP_ADSL_LINE_START returned %d\n", ret);
+		atm_err(usbatm_instance, "cxacru_atm_start: CHIP_ADSL_LINE_START returned %d\n", ret);
 		return ret;
 	}
 
@@ -383,13 +382,13 @@
 static void cxacru_poll_status(struct cxacru_data *instance)
 {
 	u32 buf[CXINF_MAX] = {};
-	struct device *dev = &instance->usbatm->usb_intf->dev;
-	struct atm_dev *atm_dev = instance->usbatm->atm_dev;
+	struct usbatm_data *usbatm = instance->usbatm;
+	struct atm_dev *atm_dev = usbatm->atm_dev;
 	int ret;
 
 	ret = cxacru_cm_get_array(instance, CM_REQUEST_CARD_INFO_GET, buf, CXINF_MAX);
 	if (ret < 0) {
-		dev_warn(dev, "poll status: error %d\n", ret);
+		atm_warn(usbatm, "poll status: error %d\n", ret);
 		goto reschedule;
 	}
 
@@ -400,50 +399,50 @@
 	switch (instance->line_status) {
 	case 0:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: down\n");
+		atm_info(usbatm, "ADSL line: down\n");
 		break;
 
 	case 1:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: attemtping to activate\n");
+		atm_info(usbatm, "ADSL line: attempting to activate\n");
 		break;
 
 	case 2:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: training\n");
+		atm_info(usbatm, "ADSL line: training\n");
 		break;
 
 	case 3:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: channel analysis\n");
+		atm_info(usbatm, "ADSL line: channel analysis\n");
 		break;
 
 	case 4:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: exchange\n");
+		atm_info(usbatm, "ADSL line: exchange\n");
 		break;
 
 	case 5:
 		atm_dev->link_rate = buf[CXINF_DOWNSTREAM_RATE] * 1000 / 424;
 		atm_dev->signal = ATM_PHY_SIG_FOUND;
 
-		dev_info(dev, "ADSL line: up (%d kb/s down | %d kb/s up)\n",
+		atm_info(usbatm, "ADSL line: up (%d kb/s down | %d kb/s up)\n",
 		     buf[CXINF_DOWNSTREAM_RATE], buf[CXINF_UPSTREAM_RATE]);
 		break;
 
 	case 6:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: waiting\n");
+		atm_info(usbatm, "ADSL line: waiting\n");
 		break;
 
 	case 7:
 		atm_dev->signal = ATM_PHY_SIG_LOST;
-		dev_info(dev, "ADSL line: initializing\n");
+		atm_info(usbatm, "ADSL line: initializing\n");
 		break;
 
 	default:
 		atm_dev->signal = ATM_PHY_SIG_UNKNOWN;
-		dev_info(dev, "Unknown line state %02x\n", instance->line_status);
+		atm_info(usbatm, "Unknown line state %02x\n", instance->line_status);
 		break;
 	}
 reschedule:
@@ -504,8 +503,8 @@
 {
 	int ret;
 	int off;
-	struct usb_device *usb_dev = instance->usbatm->usb_dev;
-	struct device *dev = &instance->usbatm->usb_intf->dev;
+	struct usbatm_data *usbatm = instance->usbatm;
+	struct usb_device *usb_dev = usbatm->usb_dev;
 	u16 signature[] = { usb_dev->descriptor.idVendor, usb_dev->descriptor.idProduct };
 	u32 val;
 
@@ -515,7 +514,7 @@
 	val = cpu_to_le32(instance->modem_type->pll_f_clk);
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, PLLFCLK_ADDR, (u8 *) &val, 4);
 	if (ret) {
-		dev_err(dev, "FirmwarePllFClkValue failed: %d\n", ret);
+		usb_err(usbatm, "FirmwarePllFClkValue failed: %d\n", ret);
 		return;
 	}
 
@@ -523,7 +522,7 @@
 	val = cpu_to_le32(instance->modem_type->pll_b_clk);
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, PLLBCLK_ADDR, (u8 *) &val, 4);
 	if (ret) {
-		dev_err(dev, "FirmwarePllBClkValue failed: %d\n", ret);
+		usb_err(usbatm, "FirmwarePllBClkValue failed: %d\n", ret);
 		return;
 	}
 
@@ -531,14 +530,14 @@
 	val = cpu_to_le32(SDRAM_ENA);
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, SDRAMEN_ADDR, (u8 *) &val, 4);
 	if (ret) {
-		dev_err(dev, "Enable SDRAM failed: %d\n", ret);
+		usb_err(usbatm, "Enable SDRAM failed: %d\n", ret);
 		return;
 	}
 
 	/* Firmware */
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, FW_ADDR, fw->data, fw->size);
 	if (ret) {
-		dev_err(dev, "Firmware upload failed: %d\n", ret);
+		usb_err(usbatm, "Firmware upload failed: %d\n", ret);
 		return;
 	}
 
@@ -546,7 +545,7 @@
 	if (instance->modem_type->boot_rom_patch) {
 		ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, BR_ADDR, bp->data, bp->size);
 		if (ret) {
-			dev_err(dev, "Boot ROM patching failed: %d\n", ret);
+			usb_err(usbatm, "Boot ROM patching failed: %d\n", ret);
 			return;
 		}
 	}
@@ -554,7 +553,7 @@
 	/* Signature */
 	ret = cxacru_fw(usb_dev, FW_WRITE_MEM, 0x2, 0x0, SIG_ADDR, (u8 *) signature, 4);
 	if (ret) {
-		dev_err(dev, "Signature storing failed: %d\n", ret);
+		usb_err(usbatm, "Signature storing failed: %d\n", ret);
 		return;
 	}
 
@@ -566,7 +565,7 @@
 		ret = cxacru_fw(usb_dev, FW_GOTO_MEM, 0x0, 0x0, FW_ADDR, NULL, 0);
 	}
 	if (ret) {
-		dev_err(dev, "Passing control to firmware failed: %d\n", ret);
+		usb_err(usbatm, "Passing control to firmware failed: %d\n", ret);
 		return;
 	}
 
@@ -580,7 +579,7 @@
 
 	ret = cxacru_cm(instance, CM_REQUEST_CARD_GET_STATUS, NULL, 0, NULL, 0);
 	if (ret < 0) {
-		dev_err(dev, "modem failed to initialize: %d\n", ret);
+		usb_err(usbatm, "modem failed to initialize: %d\n", ret);
 		return;
 	}
 
@@ -597,7 +596,7 @@
 			ret = cxacru_cm(instance, CM_REQUEST_CARD_DATA_SET,
 					(u8 *) buf, len, NULL, 0);
 			if (ret < 0) {
-				dev_err(dev, "load config data failed: %d\n", ret);
+				usb_err(usbatm, "load config data failed: %d\n", ret);
 				return;
 			}
 		}
@@ -608,18 +607,19 @@
 static int cxacru_find_firmware(struct cxacru_data *instance,
 				char* phase, const struct firmware **fw_p)
 {
-	struct device *dev = &instance->usbatm->usb_intf->dev;
+	struct usbatm_data *usbatm = instance->usbatm;
+	struct device *dev = &usbatm->usb_intf->dev;
 	char buf[16];
 
 	sprintf(buf, "cxacru-%s.bin", phase);
 	dbg("cxacru_find_firmware: looking for %s", buf);
 
 	if (request_firmware(fw_p, buf, dev)) {
-		dev_dbg(dev, "no stage %s firmware found\n", phase);
+		usb_dbg(usbatm, "no stage %s firmware found\n", phase);
 		return -ENOENT;
 	}
 
-	dev_info(dev, "found firmware %s\n", buf);
+	usb_info(usbatm, "found firmware %s\n", buf);
 
 	return 0;
 }
@@ -627,20 +627,19 @@
 static int cxacru_heavy_init(struct usbatm_data *usbatm_instance,
 			     struct usb_interface *usb_intf)
 {
-	struct device *dev = &usbatm_instance->usb_intf->dev;
 	const struct firmware *fw, *bp, *cf;
 	struct cxacru_data *instance = usbatm_instance->driver_data;
 
 	int ret = cxacru_find_firmware(instance, "fw", &fw);
 	if (ret) {
-		dev_warn(dev, "firmware (cxacru-fw.bin) unavailable (hotplug misconfiguration?)\n");
+		usb_warn(usbatm_instance, "firmware (cxacru-fw.bin) unavailable (system misconfigured?)\n");
 		return ret;
 	}
 
 	if (instance->modem_type->boot_rom_patch) {
 		ret = cxacru_find_firmware(instance, "bp", &bp);
 		if (ret) {
-			dev_warn(dev, "boot ROM patch (cxacru-bp.bin) unavailable (hotplug misconfiguration?)\n");
+			usb_warn(usbatm_instance, "boot ROM patch (cxacru-bp.bin) unavailable (system misconfigured?)\n");
 			release_firmware(fw);
 			return ret;
 		}
@@ -787,12 +786,12 @@
 	{ /* V = Conexant			P = ADSL modem (Hasbani project)	*/
 		USB_DEVICE(0x0572, 0xcb00),	.driver_info = (unsigned long) &cxacru_cb00
 	},
-	{ /* V = Conexant             P = ADSL modem (Well PTI-800 */
-		USB_DEVICE(0x0572, 0xcb02),	.driver_info = (unsigned long) &cxacru_cb00
-	},
 	{ /* V = Conexant			P = ADSL modem				*/
 		USB_DEVICE(0x0572, 0xcb01),	.driver_info = (unsigned long) &cxacru_cb00
 	},
+	{ /* V = Conexant			P = ADSL modem (Well PTI-800) */
+		USB_DEVICE(0x0572, 0xcb02),	.driver_info = (unsigned long) &cxacru_cb00
+	},
 	{ /* V = Conexant			P = ADSL modem				*/
 		USB_DEVICE(0x0572, 0xcb06),	.driver_info = (unsigned long) &cxacru_cb00
 	},
drivers/usb/atm/speedtch.c renamed from drivers/usb/atm.orig/speedtch.c +30 -23

165 lines not on this page · raw message

drivers/usb/atm/usbatm.c renamed from drivers/usb/atm.orig/usbatm.c +60 -41

291 lines not on this page · raw message

drivers/usb/atm/usbatm.h renamed from drivers/usb/atm.orig/usbatm.h +17 -8
diff -x '*.orig' -x '*.base' -u -r Linux/drivers/usb/atm.orig/usbatm.h Linux/drivers/usb/atm/usbatm.h
@@ -24,22 +24,21 @@
 #ifndef	_USBATM_H_
 #define	_USBATM_H_
 
-#include <linux/config.h>
-
-/*
-#define VERBOSE_DEBUG
-*/
-
 #include <asm/semaphore.h>
 #include <linux/atm.h>
 #include <linux/atmdev.h>
 #include <linux/completion.h>
 #include <linux/device.h>
+#include <linux/kernel.h>
 #include <linux/kref.h>
 #include <linux/list.h>
 #include <linux/stringify.h>
 #include <linux/usb.h>
 
+/*
+#define VERBOSE_DEBUG
+*/
+
 #ifdef DEBUG
 #define UDSL_ASSERT(x)	BUG_ON(!(x))
 #else
@@ -52,8 +51,13 @@
 	dev_info(&(instance)->usb_intf->dev , format , ## arg)
 #define usb_warn(instance, format, arg...)	\
 	dev_warn(&(instance)->usb_intf->dev , format , ## arg)
+#ifdef DEBUG
+#define usb_dbg(instance, format, arg...)	\
+        dev_printk(KERN_DEBUG , &(instance)->usb_intf->dev , format , ## arg)
+#else
 #define usb_dbg(instance, format, arg...)	\
-	dev_dbg(&(instance)->usb_intf->dev , format , ## arg)
+	do {} while (0)
+#endif
 
 /* FIXME: move to dev_* once ATM is driver model aware */
 #define atm_printk(level, instance, format, arg...)	\
@@ -69,9 +73,14 @@
 #ifdef DEBUG
 #define atm_dbg(instance, format, arg...)	\
 	atm_printk(KERN_DEBUG, instance , format , ## arg)
+#define atm_rldbg(instance, format, arg...)	\
+	if (printk_ratelimit())				\
+		atm_printk(KERN_DEBUG, instance , format , ## arg)
 #else
 #define atm_dbg(instance, format, arg...)	\
 	do {} while (0)
+#define atm_rldbg(instance, format, arg...)	\
+	do {} while (0)
 #endif
 
 
@@ -171,7 +180,7 @@
 	struct usbatm_channel tx_channel;
 
 	struct sk_buff_head sndqueue;
-	struct sk_buff *current_skb;			/* being emptied */
+	struct sk_buff *current_skb;	/* being emptied */
 
 	struct urb *urbs[0];
 };
drivers/usb/atm/xusbatm.c renamed from drivers/usb/atm.orig/xusbatm.c +12 -11
diff -x '*.orig' -x '*.base' -u -r Linux/drivers/usb/atm.orig/xusbatm.c Linux/drivers/usb/atm/xusbatm.c
@@ -61,7 +61,7 @@
 	return 0;
 }
 
-static int xusbatm_bind(struct usbatm_data *usbatm_instance,
+static int xusbatm_bind(struct usbatm_data *usbatm,
 			struct usb_interface *intf, const struct usb_device_id *id,
 			int *need_heavy_init)
 {
@@ -72,14 +72,14 @@
 	u8 searched_ep = rx_ep_present ? tx_endpoint[drv_ix] : rx_endpoint[drv_ix];
 	int i, ret;
 
-	usb_dbg(usbatm_instance, "%s: binding driver %d: vendor %#x product %#x"
-		" rx: ep %#x padd %d tx: ep %#x padd %d\n",
+	usb_dbg(usbatm, "%s: binding driver %d: vendor %04x product %04x"
+		" rx: ep %02x padd %d tx: ep %02x padd %d\n",
 		__func__, drv_ix, vendor[drv_ix], product[drv_ix],
 		rx_endpoint[drv_ix], rx_padding[drv_ix],
 		tx_endpoint[drv_ix], tx_padding[drv_ix]);
 
 	if (!rx_ep_present && !tx_ep_present) {
-		usb_dbg(usbatm_instance, "%s: intf #%d has neither rx (%#x) nor tx (%#x) endpoint\n",
+		usb_dbg(usbatm, "%s: intf #%d has neither rx (%#x) nor tx (%#x) endpoint\n",
 			__func__, intf->altsetting->desc.bInterfaceNumber,
 			rx_endpoint[drv_ix], tx_endpoint[drv_ix]);
 		return -ENODEV;
@@ -93,25 +93,26 @@
 
 		if (cur_if != intf && usb_intf_has_ep(cur_if, searched_ep)) {
 			ret = usb_driver_claim_interface(&xusbatm_usb_driver,
-							 cur_if, usbatm_instance);
+							 cur_if, usbatm);
 			if (!ret)
-				usb_err(usbatm_instance, "%s: failed to claim interface #%d (%d)\n",
+				usb_err(usbatm, "%s: failed to claim interface #%d (%d)\n",
 					__func__, cur_if->altsetting->desc.bInterfaceNumber, ret);
 			return ret;
 		}
 	}
 
-	usb_err(usbatm_instance, "%s: no interface has endpoint %#x\n",
+	usb_err(usbatm, "%s: no interface has endpoint %#x\n",
 		__func__, searched_ep);
 	return -ENODEV;
 }
 
-static void xusbatm_unbind(struct usbatm_data *usbatm_instance,
+static void xusbatm_unbind(struct usbatm_data *usbatm,
 			   struct usb_interface *intf)
 {
 	struct usb_device *usb_dev = interface_to_usbdev(intf);
 	int i;
-	usb_dbg(usbatm_instance, "%s entered\n", __func__);
+
+	usb_dbg(usbatm, "%s entered\n", __func__);
 
 	for(i = 0; i < usb_dev->actconfig->desc.bNumInterfaces; i++) {
 		struct usb_interface *cur_if = usb_dev->actconfig->interface[i];
@@ -120,10 +121,10 @@
 	}
 }
 
-static int xusbatm_atm_start(struct usbatm_data *usbatm_instance,
+static int xusbatm_atm_start(struct usbatm_data *usbatm,
 			     struct atm_dev *atm_dev)
 {
-	atm_dbg(usbatm_instance, "%s entered\n", __func__);
+	atm_dbg(usbatm, "%s entered\n", __func__);
 
 	/* use random MAC as we've no way to get it from the device */
 	random_ether_addr(atm_dev->esi);
#3 lore raw

PATCH 2/13 USBATM: add flags field

In reply to Duncan Sands

Have minidrivers and the core signal special requirements using a flags field in struct usbatm_data. For the moment this is only used to replace the need_heavy_init bind parameter, but there'll be new flags in later patches.

drivers/usb/atm/cxacru.c renamed from drivers/usb/atm.orig/cxacru.c +2 -3
diff -x '*.orig' -x '*.base' -u -r Linux/drivers/usb/atm.orig/cxacru.c Linux/drivers/usb/atm/cxacru.c
@@ -666,8 +666,7 @@
 }
 
 static int cxacru_bind(struct usbatm_data *usbatm_instance,
-		       struct usb_interface *intf, const struct usb_device_id *id,
-		       int *need_heavy_init)
+		       struct usb_interface *intf, const struct usb_device_id *id)
 {
 	struct cxacru_data *instance;
 	struct usb_device *usb_dev = interface_to_usbdev(intf);
@@ -726,7 +725,7 @@
 
 	usbatm_instance->driver_data = instance;
 
-	*need_heavy_init = cxacru_card_status(instance);
+	usbatm_instance->flags = (cxacru_card_status(instance) ? 0 : UDSL_SKIP_HEAVY_INIT);
 
 	return 0;
 

Only in Linux/drivers/usb/atm: done
Only in Linux/drivers/usb/atm.orig/patches: messages

drivers/usb/atm/speedtch.c renamed from drivers/usb/atm.orig/speedtch.c +4 -5
diff -x '*.orig' -x '*.base' -u -r Linux/drivers/usb/atm.orig/speedtch.c Linux/drivers/usb/atm/speedtch.c
@@ -681,8 +681,7 @@
 
 static int speedtch_bind(struct usbatm_data *usbatm,
 			 struct usb_interface *intf,
-			 const struct usb_device_id *id,
-			 int *need_heavy_init)
+			 const struct usb_device_id *id)
 {
 	struct usb_device *usb_dev = interface_to_usbdev(intf);
 	struct usb_interface *cur_intf;
@@ -754,11 +753,11 @@
 			      0x12, 0xc0, 0x07, 0x00,
 			      instance->scratch_buffer + OFFSET_7, SIZE_7, 500);
 
-	*need_heavy_init = (ret != SIZE_7);
+	usbatm->flags = (ret == SIZE_7 ? UDSL_SKIP_HEAVY_INIT : 0);
 
-	usb_dbg(usbatm, "%s: firmware %s loaded\n", __func__, need_heavy_init ? "not" : "already");
+	usb_dbg(usbatm, "%s: firmware %s loaded\n", __func__, usbatm->flags & UDSL_SKIP_HEAVY_INIT ? "already" : "not");
 
-	if (*need_heavy_init)
+	if (!(usbatm->flags & UDSL_SKIP_HEAVY_INIT))
 		if ((ret = usb_reset_device(usb_dev)) < 0) {
 			usb_err(usbatm, "%s: device reset failed (%d)!\n", __func__, ret);
 			goto fail_free;
drivers/usb/atm/ueagle-atm.c renamed from drivers/usb/atm.orig/ueagle-atm.c +2 -2
diff -x '*.orig' -x '*.base' -u -r Linux/drivers/usb/atm.orig/ueagle-atm.c Linux/drivers/usb/atm/ueagle-atm.c
@@ -1617,7 +1617,7 @@
 }
 
 static int uea_bind(struct usbatm_data *usbatm, struct usb_interface *intf,
-		   const struct usb_device_id *id, int *heavy)
+		   const struct usb_device_id *id)
 {
 	struct usb_device *usb = interface_to_usbdev(intf);
 	struct uea_softc *sc;
@@ -1629,7 +1629,7 @@
 	if (ifnum != UEA_INTR_IFACE_NO)
 		return -ENODEV;
 
-	*heavy = sync_wait[modem_index];
+	usbatm_instance->flags = (sync_wait[modem_index] ? 0 : UDSL_SKIP_HEAVY_INIT);
 
 	/* interface 1 is for outbound traffic */
 	ret = claim_interface(usb, usbatm, UEA_US_IFACE_NO);
drivers/usb/atm/usbatm.c renamed from drivers/usb/atm.orig/usbatm.c +2 -4
diff -x '*.orig' -x '*.base' -u -r Linux/drivers/usb/atm.orig/usbatm.c Linux/drivers/usb/atm/usbatm.c
@@ -969,7 +969,6 @@
 	char *buf;
 	int error = -ENOMEM;
 	int i, length;
-	int need_heavy;
 
 	dev_dbg(dev, "%s: trying driver %s with vendor=%04x, product=%04x, ifnum %2d\n",
 			__func__, driver->driver_name,
@@ -1014,8 +1013,7 @@
 	snprintf(buf, length, ")");
 
  bind:
-	need_heavy = 1;
-	if (driver->bind && (error = driver->bind(instance, intf, id, &need_heavy)) < 0) {
+	if (driver->bind && (error = driver->bind(instance, intf, id)) < 0) {
 			dev_err(dev, "%s: bind failed: %d!\n", __func__, error);
 			goto fail_free;
 	}
@@ -1098,7 +1096,7 @@
 		     __func__, urb->transfer_buffer, urb->transfer_buffer_length, urb);
 	}
 
-	if (need_heavy && driver->heavy_init) {
+	if (!(instance->flags & UDSL_SKIP_HEAVY_INIT) && driver->heavy_init) {
 		error = usbatm_heavy_init(instance);
 	} else {
 		complete(&instance->thread_exited);	/* pretend that heavy_init was run */
drivers/usb/atm/usbatm.h renamed from drivers/usb/atm.orig/usbatm.h +8 -5
diff -x '*.orig' -x '*.base' -u -r Linux/drivers/usb/atm.orig/usbatm.h Linux/drivers/usb/atm/usbatm.h
@@ -84,6 +84,11 @@
 #endif
 
 
+/* flags, set by mini-driver in bind() */
+
+#define UDSL_SKIP_HEAVY_INIT	(1<<0)
+
+
 /* mini driver */
 
 struct usbatm_data;
@@ -99,12 +104,9 @@
 
 	const char *driver_name;
 
-	/*
-	*  init device ... can sleep, or cause probe() failure.  Drivers with a heavy_init
-	*  method can avoid having it called by setting need_heavy_init to zero.
-	*/
+	/* init device ... can sleep, or cause probe() failure */
         int (*bind) (struct usbatm_data *, struct usb_interface *,
-		     const struct usb_device_id *id, int *need_heavy_init);
+		     const struct usb_device_id *id);
 
 	/* additional device initialization that is too slow to be done in probe() */
         int (*heavy_init) (struct usbatm_data *, struct usb_interface *);
@@ -152,6 +154,7 @@
 	struct usbatm_driver *driver;
 	void *driver_data;
 	char driver_name[16];
+	unsigned int flags; /* set by mini-driver in bind() */
 
 	/* USB device */
 	struct usb_device *usb_dev;
drivers/usb/atm/xusbatm.c renamed from drivers/usb/atm.orig/xusbatm.c +1 -2
diff -x '*.orig' -x '*.base' -u -r Linux/drivers/usb/atm.orig/xusbatm.c Linux/drivers/usb/atm/xusbatm.c
@@ -62,8 +62,7 @@
 }
 
 static int xusbatm_bind(struct usbatm_data *usbatm,
-			struct usb_interface *intf, const struct usb_device_id *id,
-			int *need_heavy_init)
+			struct usb_interface *intf, const struct usb_device_id *id)
 {
 	struct usb_device *usb_dev = interface_to_usbdev(intf);
 	int drv_ix = id - xusbatm_usb_ids;
#4 lore raw
In reply to Duncan Sands
Quoted 2 lines · Duncan Sands

Hi Greg, here are some fixes and improvements to the USB ATM modem drivers, in thirteen patches:

I only got 2 of these, is my mail just being slow (which it does at odd times), or did you stop sending them based on some problems on your end?

thanks,

greg k-h

#5 lore raw
Quoted 2 lines

I only got 2 of these, is my mail just being slow (which it does at odd times), or did you stop sending them based on some problems on your end?

I stopped sending them based on problems on my end. I'll send the rest tomorrow.

Ciao,

Duncan.

#6 lore raw
In reply to Greg KH
Quoted 2 lines

I only got 2 of these, is my mail just being slow (which it does at odd times), or did you stop sending them based on some problems on your end?

Hi Greg, I stopped because I noticed that part of patch 2 had slipped into patch 3 (the bit that slipped was exactly the tweak I made to patch 2 to have it compile by itself... probably ended up in patch 3 due to a forgotten "quilt refresh"), and I wanted to check all the other patches. They are fine, so I have now sent them. However, patch 2 won't compile unless you apply patch 3 as well. Since they are both trivial, I hope you are ok with that, otherwise I can rediff them

All the best,

Duncan.

#7 lore raw

PATCH 3/13 USBATM: remove .owner

In reply to Duncan Sands

Remove the unused .owner field in struct usbatm_driver.

drivers/usb/atm/cxacru.c +0 -1
Index: Linux/drivers/usb/atm/cxacru.c
===================================================================
@@ -833,7 +833,6 @@
 MODULE_DEVICE_TABLE(usb, cxacru_usb_ids);
 
 static struct usbatm_driver cxacru_driver = {
-	.owner		= THIS_MODULE,
 	.driver_name	= cxacru_driver_name,
 	.bind		= cxacru_bind,
 	.heavy_init	= cxacru_heavy_init,
drivers/usb/atm/speedtch.c +0 -1
Index: Linux/drivers/usb/atm/speedtch.c
===================================================================
@@ -793,7 +793,6 @@
 ***********/
 
 static struct usbatm_driver speedtch_usbatm_driver = {
-	.owner		= THIS_MODULE,
 	.driver_name	= speedtch_driver_name,
 	.bind		= speedtch_bind,
 	.heavy_init	= speedtch_heavy_init,
drivers/usb/atm/ueagle-atm.c +1 -2
Index: Linux/drivers/usb/atm/ueagle-atm.c
===================================================================
@@ -1629,7 +1629,7 @@
 	if (ifnum != UEA_INTR_IFACE_NO)
 		return -ENODEV;
 
-	usbatm_instance->flags = (sync_wait[modem_index] ? 0 : UDSL_SKIP_HEAVY_INIT);
+	usbatm->flags = (sync_wait[modem_index] ? 0 : UDSL_SKIP_HEAVY_INIT);
 
 	/* interface 1 is for outbound traffic */
 	ret = claim_interface(usb, usbatm, UEA_US_IFACE_NO);
@@ -1701,7 +1701,6 @@
 
 static struct usbatm_driver uea_usbatm_driver = {
 	.driver_name = "ueagle-atm",
-	.owner = THIS_MODULE,
 	.bind = uea_bind,
 	.atm_start = uea_atm_open,
 	.unbind = uea_unbind,
drivers/usb/atm/usbatm.h +0 -2
Index: Linux/drivers/usb/atm/usbatm.h
===================================================================
@@ -100,8 +100,6 @@
 */
 
 struct usbatm_driver {
-	struct module *owner;
-
 	const char *driver_name;
 
 	/* init device ... can sleep, or cause probe() failure */
drivers/usb/atm/xusbatm.c +0 -1
Index: Linux/drivers/usb/atm/xusbatm.c
===================================================================
@@ -166,7 +166,6 @@
 		xusbatm_usb_ids[i].idProduct	= product[i];
 
 
-		xusbatm_drivers[i].owner	= THIS_MODULE;
 		xusbatm_drivers[i].driver_name	= xusbatm_driver_name;
 		xusbatm_drivers[i].bind		= xusbatm_bind;
 		xusbatm_drivers[i].unbind	= xusbatm_unbind;
#8 lore raw

PATCH 4/13 USBATM: kzalloc conversion

In reply to Duncan Sands

Convert kmalloc + memset to kzalloc.

drivers/usb/atm/cxacru.c +1 -3
Index: Linux/drivers/usb/atm/cxacru.c
===================================================================
@@ -673,14 +673,12 @@
 	int ret;
 
 	/* instance init */
-	instance = kmalloc(sizeof(*instance), GFP_KERNEL);
+	instance = kzalloc(sizeof(*instance), GFP_KERNEL);
 	if (!instance) {
 		dbg("cxacru_bind: no memory for instance data");
 		return -ENOMEM;
 	}
 
-	memset(instance, 0, sizeof(*instance));
-
 	instance->usbatm = usbatm_instance;
 	instance->modem_type = (struct cxacru_modem_type *) id->driver_info;
 
drivers/usb/atm/speedtch.c +1 -3
Index: Linux/drivers/usb/atm/speedtch.c
===================================================================
@@ -715,7 +715,7 @@
 		}
 	}
 
-	instance = kmalloc(sizeof(*instance), GFP_KERNEL);
+	instance = kzalloc(sizeof(*instance), GFP_KERNEL);
 
 	if (!instance) {
 		usb_err(usbatm, "%s: no memory for instance data!\n", __func__);
@@ -723,8 +723,6 @@
 		goto fail_release;
 	}
 
-	memset(instance, 0, sizeof(struct speedtch_instance_data));
-
 	instance->usbatm = usbatm;
 
 	INIT_WORK(&instance->status_checker, (void *)speedtch_check_status, instance);
drivers/usb/atm/usbatm.c +3 -5
Index: Linux/drivers/usb/atm/usbatm.c
===================================================================
@@ -763,13 +763,12 @@
 		goto fail;
 	}
 
-	if (!(new = kmalloc(sizeof(struct usbatm_vcc_data), GFP_KERNEL))) {
+	if (!(new = kzalloc(sizeof(struct usbatm_vcc_data), GFP_KERNEL))) {
 		atm_err(instance, "%s: no memory for vcc_data!\n", __func__);
 		ret = -ENOMEM;
 		goto fail;
 	}
 
-	memset(new, 0, sizeof(struct usbatm_vcc_data));
 	new->vcc = vcc;
 	new->vpi = vpi;
 	new->vci = vci;
@@ -1066,13 +1065,12 @@
 
 		instance->urbs[i] = urb;
 
-		buffer = kmalloc(channel->buf_size, GFP_KERNEL);
+		/* zero the tx padding to avoid leaking information */
+		buffer = kzalloc(channel->buf_size, GFP_KERNEL);
 		if (!buffer) {
 			dev_err(dev, "%s: no memory for buffer %d!\n", __func__, i);
 			goto fail_unbind;
 		}
-		/* zero the tx padding to avoid leaking information */
-		memset(buffer, 0, channel->buf_size);
 
 		usb_fill_bulk_urb(urb, instance->usb_dev, channel->endpoint,
 				  buffer, channel->buf_size, usbatm_complete, channel);
#9 lore raw

PATCH 5/13 USBATM: xusbatm rewrite

In reply to Duncan Sands

The xusbatm driver is for otherwise unsupported modems. All it does is grab hold of a user-specified set of interfaces - the generic usbatm core methods (hopefully) do the rest. As Aurelio Arroyo discovered when he tried to use xusbatm (big mistake!), the interface grabbing logic was completely borked. Here is a rewrite that works.

drivers/usb/atm/xusbatm.c +76 -36
Index: Linux/drivers/usb/atm/xusbatm.c
===================================================================
@@ -41,6 +41,8 @@
 XUSBATM_PARM(tx_endpoint, unsigned char, byte, "tx endpoint number");
 XUSBATM_PARM(rx_padding, unsigned char, byte, "rx padding (default 0)");
 XUSBATM_PARM(tx_padding, unsigned char, byte, "tx padding (default 0)");
+XUSBATM_PARM(rx_altsetting, unsigned char, byte, "rx altsetting (default 0)");
+XUSBATM_PARM(tx_altsetting, unsigned char, byte, "rx altsetting (default 0)");
 
 static const char xusbatm_driver_name[] = "xusbatm";
 
@@ -48,61 +50,94 @@
 static struct usb_device_id xusbatm_usb_ids[XUSBATM_DRIVERS_MAX + 1];
 static struct usb_driver xusbatm_usb_driver;
 
-static int usb_intf_has_ep(const struct usb_interface *intf, u8 ep)
+static struct usb_interface *xusbatm_find_intf (struct usb_device *usb_dev, int altsetting, u8 ep)
 {
+	struct usb_host_interface *alt;
+	struct usb_interface *intf;
 	int i, j;
 
-	for (i = 0; i < intf->num_altsetting; i++) {
-		struct usb_host_interface *alt = intf->altsetting;
-		for (j = 0; j < alt->desc.bNumEndpoints; j++)
-			if ((alt->endpoint[i].desc.bEndpointAddress & USB_ENDPOINT_NUMBER_MASK) == ep)
-				return 1;
+	for(i = 0; i < usb_dev->actconfig->desc.bNumInterfaces; i++)
+		if ((intf = usb_dev->actconfig->interface[i]) && (alt = usb_altnum_to_altsetting(intf, altsetting)))
+			for (j = 0; j < alt->desc.bNumEndpoints; j++)
+				if (alt->endpoint[j].desc.bEndpointAddress == ep)
+					return intf;
+	return NULL;
+}
+
+static int xusbatm_capture_intf (struct usbatm_data *usbatm, struct usb_device *usb_dev,
+		struct usb_interface *intf, int altsetting, int claim)
+{
+	int ifnum = intf->altsetting->desc.bInterfaceNumber;
+	int ret;
+
+	if (claim && (ret = usb_driver_claim_interface(&xusbatm_usb_driver, intf, usbatm))) {
+		usb_err(usbatm, "%s: failed to claim interface %2d (%d)!\n", __func__, ifnum, ret);
+		return ret;
+	}
+	if ((ret = usb_set_interface(usb_dev, ifnum, altsetting))) {
+		usb_err(usbatm, "%s: altsetting %2d for interface %2d failed (%d)!\n", __func__, altsetting, ifnum, ret);
+		return ret;
 	}
 	return 0;
 }
 
+static void xusbatm_release_intf (struct usb_device *usb_dev, struct usb_interface *intf, int claimed)
+{
+	if (claimed) {
+		usb_set_intfdata(intf, NULL);
+		usb_driver_release_interface(&xusbatm_usb_driver, intf);
+	}
+}
+
 static int xusbatm_bind(struct usbatm_data *usbatm,
 			struct usb_interface *intf, const struct usb_device_id *id)
 {
 	struct usb_device *usb_dev = interface_to_usbdev(intf);
 	int drv_ix = id - xusbatm_usb_ids;
-	int rx_ep_present = usb_intf_has_ep(intf, rx_endpoint[drv_ix]);
-	int tx_ep_present = usb_intf_has_ep(intf, tx_endpoint[drv_ix]);
-	u8 searched_ep = rx_ep_present ? tx_endpoint[drv_ix] : rx_endpoint[drv_ix];
-	int i, ret;
+	int rx_alt = rx_altsetting[drv_ix];
+	int tx_alt = tx_altsetting[drv_ix];
+	struct usb_interface *rx_intf = xusbatm_find_intf(usb_dev, rx_alt, rx_endpoint[drv_ix]);
+	struct usb_interface *tx_intf = xusbatm_find_intf(usb_dev, tx_alt, tx_endpoint[drv_ix]);
+	int ret;
 
 	usb_dbg(usbatm, "%s: binding driver %d: vendor %04x product %04x"
-		" rx: ep %02x padd %d tx: ep %02x padd %d\n",
+		" rx: ep %02x padd %d alt %2d tx: ep %02x padd %d alt %2d\n",
 		__func__, drv_ix, vendor[drv_ix], product[drv_ix],
-		rx_endpoint[drv_ix], rx_padding[drv_ix],
-		tx_endpoint[drv_ix], tx_padding[drv_ix]);
+		rx_endpoint[drv_ix], rx_padding[drv_ix], rx_alt,
+		tx_endpoint[drv_ix], tx_padding[drv_ix], tx_alt);
 
-	if (!rx_ep_present && !tx_ep_present) {
-		usb_dbg(usbatm, "%s: intf #%d has neither rx (%#x) nor tx (%#x) endpoint\n",
-			__func__, intf->altsetting->desc.bInterfaceNumber,
-			rx_endpoint[drv_ix], tx_endpoint[drv_ix]);
+	if (!rx_intf || !tx_intf) {
+		if (!rx_intf)
+			usb_dbg(usbatm, "%s: no interface contains endpoint %02x in altsetting %2d\n",
+				__func__, rx_endpoint[drv_ix], rx_alt);
+		if (!tx_intf)
+			usb_dbg(usbatm, "%s: no interface contains endpoint %02x in altsetting %2d\n",
+				__func__, tx_endpoint[drv_ix], tx_alt);
 		return -ENODEV;
 	}
 
-	if (rx_ep_present && tx_ep_present)
-		return 0;
+	if ((rx_intf != intf) && (tx_intf != intf))
+		return -ENODEV;
 
-	for(i = 0; i < usb_dev->actconfig->desc.bNumInterfaces; i++) {
-		struct usb_interface *cur_if = usb_dev->actconfig->interface[i];
+	if ((rx_intf == tx_intf) && (rx_alt != tx_alt)) {
+		usb_err(usbatm, "%s: altsettings clash on interface %2d (%2d vs %2d)!\n", __func__,
+				rx_intf->altsetting->desc.bInterfaceNumber, rx_alt, tx_alt);
+		return -EINVAL;
+	}
 
-		if (cur_if != intf && usb_intf_has_ep(cur_if, searched_ep)) {
-			ret = usb_driver_claim_interface(&xusbatm_usb_driver,
-							 cur_if, usbatm);
-			if (!ret)
-				usb_err(usbatm, "%s: failed to claim interface #%d (%d)\n",
-					__func__, cur_if->altsetting->desc.bInterfaceNumber, ret);
-			return ret;
-		}
+	usb_dbg(usbatm, "%s: rx If#=%2d; tx If#=%2d\n", __func__,
+			rx_intf->altsetting->desc.bInterfaceNumber,
+			tx_intf->altsetting->desc.bInterfaceNumber);
+
+	if ((ret = xusbatm_capture_intf(usbatm, usb_dev, rx_intf, rx_alt, rx_intf != intf)))
+		return ret;
+
+	if ((tx_intf != rx_intf) && (ret = xusbatm_capture_intf(usbatm, usb_dev, tx_intf, tx_alt, tx_intf != intf))) {
+		xusbatm_release_intf(usb_dev, rx_intf, rx_intf != intf);
+		return ret;
 	}
 
-	usb_err(usbatm, "%s: no interface has endpoint %#x\n",
-		__func__, searched_ep);
-	return -ENODEV;
+	return 0;
 }
 
 static void xusbatm_unbind(struct usbatm_data *usbatm,
@@ -114,9 +149,12 @@
 	usb_dbg(usbatm, "%s entered\n", __func__);
 
 	for(i = 0; i < usb_dev->actconfig->desc.bNumInterfaces; i++) {
-		struct usb_interface *cur_if = usb_dev->actconfig->interface[i];
-		usb_set_intfdata(cur_if, NULL);
-		usb_driver_release_interface(&xusbatm_usb_driver, cur_if);
+		struct usb_interface *cur_intf = usb_dev->actconfig->interface[i];
+
+		if (cur_intf && (usb_get_intfdata(cur_intf) == usbatm)) {
+			usb_set_intfdata(cur_intf, NULL);
+			usb_driver_release_interface(&xusbatm_usb_driver, cur_intf);
+		}
 	}
 }
 
@@ -161,11 +199,13 @@
 	}
 
 	for (i = 0; i < num_vendor; i++) {
+		rx_endpoint[i] |= USB_DIR_IN;
+		tx_endpoint[i] &= USB_ENDPOINT_NUMBER_MASK;
+
 		xusbatm_usb_ids[i].match_flags	= USB_DEVICE_ID_MATCH_DEVICE;
 		xusbatm_usb_ids[i].idVendor	= vendor[i];
 		xusbatm_usb_ids[i].idProduct	= product[i];
 
-
 		xusbatm_drivers[i].driver_name	= xusbatm_driver_name;
 		xusbatm_drivers[i].bind		= xusbatm_bind;
 		xusbatm_drivers[i].unbind	= xusbatm_unbind;
#10 lore raw

PATCH 6/13 USBATM: shutdown open connections when disconnected

In reply to Duncan Sands

This patch causes vcc_release_async to be applied to any open vcc's when the modem is disconnected. This signals a socket shutdown, letting the socket user know that the game is up. I wrote this patch because of reports that pppd would keep connections open forever when the modem is disconnected. This patch does not fix that problem, but it's a step in the right direction. It doesn't help because the pppoatm module doesn't yet monitor state changes on the ATM socket, so simply never realises that the ATM connection has gone down (meaning it doesn't tell the ppp layer). But at least there is a socket state change now. Unfortunately this patch may create problems for those rare users like me who use routed IP or some other non-ppp connection method that goes via the ATM ARP daemon: the daemon is buggy, and with this patch will crash when the modem is disconnected. Users with a buggy atmarpd can simply restart it after disconnecting the modem.

drivers/usb/atm/usbatm.c +47 -19
Index: Linux/drivers/usb/atm/usbatm.c
===================================================================
@@ -602,8 +602,12 @@
 
 	vdbg("%s called (skb 0x%p, len %u)", __func__, skb, skb->len);
 
-	if (!instance) {
-		dbg("%s: NULL data!", __func__);
+	/* racy disconnection check - fine */
+	if (!instance || instance->disconnected) {
+#ifdef DEBUG
+		if (printk_ratelimit())
+			printk(KERN_DEBUG "%s: %s!\n", __func__, instance ? "disconnected" : "NULL instance");
+#endif
 		err = -ENODEV;
 		goto fail;
 	}
@@ -715,15 +719,19 @@
 			       atomic_read(&atm_dev->stats.aal5.rx_err),
 			       atomic_read(&atm_dev->stats.aal5.rx_drop));
 
-	if (!left--)
-		switch (atm_dev->signal) {
-		case ATM_PHY_SIG_FOUND:
-			return sprintf(page, "Line up\n");
-		case ATM_PHY_SIG_LOST:
-			return sprintf(page, "Line down\n");
-		default:
-			return sprintf(page, "Line state unknown\n");
-		}
+	if (!left--) {
+		if (instance->disconnected)
+			return sprintf(page, "Disconnected\n");
+		else
+			switch (atm_dev->signal) {
+			case ATM_PHY_SIG_FOUND:
+				return sprintf(page, "Line up\n");
+			case ATM_PHY_SIG_LOST:
+				return sprintf(page, "Line down\n");
+			default:
+				return sprintf(page, "Line state unknown\n");
+			}
+	}
 
 	return 0;
 }
@@ -757,6 +765,12 @@
 
 	down(&instance->serialize);	/* vs self, usbatm_atm_close, usbatm_usb_disconnect */
 
+	if (instance->disconnected) {
+		atm_dbg(instance, "%s: disconnected!\n", __func__);
+		ret = -ENODEV;
+		goto fail;
+	}
+
 	if (usbatm_find_vcc(instance, vpi, vci)) {
 		atm_dbg(instance, "%s: %hd/%d already in use!\n", __func__, vpi, vci);
 		ret = -EADDRINUSE;
@@ -845,6 +859,13 @@
 static int usbatm_atm_ioctl(struct atm_dev *atm_dev, unsigned int cmd,
 			  void __user * arg)
 {
+	struct usbatm_data *instance = atm_dev->dev_data;
+
+	if (!instance || instance->disconnected) {
+		dbg("%s: %s!", __func__, instance ? "disconnected" : "NULL instance");
+		return -ENODEV;
+	}
+
 	switch (cmd) {
 	case ATM_QUERYLOOP:
 		return put_user(ATM_LM_NONE, (int __user *)arg) ? -EFAULT : 0;
@@ -1129,6 +1150,7 @@
 {
 	struct device *dev = &intf->dev;
 	struct usbatm_data *instance = usb_get_intfdata(intf);
+	struct usbatm_vcc_data *vcc_data;
 	int i;
 
 	dev_dbg(dev, "%s entered\n", __func__);
@@ -1141,12 +1163,18 @@
 	usb_set_intfdata(intf, NULL);
 
 	down(&instance->serialize);
+	instance->disconnected = 1;
 	if (instance->thread_pid >= 0)
 		kill_proc(instance->thread_pid, SIGTERM, 1);
 	up(&instance->serialize);
 
 	wait_for_completion(&instance->thread_exited);
 
+	down(&instance->serialize);
+	list_for_each_entry(vcc_data, &instance->vcc_list, list)
+		vcc_release_async(vcc_data->vcc, -EPIPE);
+	up(&instance->serialize);
+
 	tasklet_disable(&instance->rx_channel.tasklet);
 	tasklet_disable(&instance->tx_channel.tasklet);
 
@@ -1156,6 +1184,14 @@
 	del_timer_sync(&instance->rx_channel.delay);
 	del_timer_sync(&instance->tx_channel.delay);
 
+	/* turn usbatm_[rt]x_process into something close to a no-op */
+	/* no need to take the spinlock */
+	INIT_LIST_HEAD(&instance->rx_channel.list);
+	INIT_LIST_HEAD(&instance->tx_channel.list);
+
+	tasklet_enable(&instance->rx_channel.tasklet);
+	tasklet_enable(&instance->tx_channel.tasklet);
+
 	if (instance->atm_dev && instance->driver->atm_stop)
 		instance->driver->atm_stop(instance, instance->atm_dev);
 
@@ -1164,14 +1200,6 @@
 
 	instance->driver_data = NULL;
 
-	/* turn usbatm_[rt]x_process into noop */
-	/* no need to take the spinlock */
-	INIT_LIST_HEAD(&instance->rx_channel.list);
-	INIT_LIST_HEAD(&instance->tx_channel.list);
-
-	tasklet_enable(&instance->rx_channel.tasklet);
-	tasklet_enable(&instance->tx_channel.tasklet);
-
 	for (i = 0; i < num_rcv_urbs + num_snd_urbs; i++) {
 		kfree(instance->urbs[i]->transfer_buffer);
 		usb_free_urb(instance->urbs[i]);
drivers/usb/atm/usbatm.h +1 -0
Index: Linux/drivers/usb/atm/usbatm.h
===================================================================
@@ -168,6 +168,7 @@
 
 	struct kref refcount;
 	struct semaphore serialize;
+	int disconnected;
 
 	/* heavy init */
 	int thread_pid;
#11 lore raw

R: [PATCH 06/13] USBATM: shutdown open connections when disconnected

Quoted 24 lines

-----Messaggio originale-----
Da: [email protected] [mailto:[email protected]]Per conto di Duncan Sands
Inviato: venerdì 13 gennaio 2006 10.05
A: Greg KH
Cc: [email protected]; [email protected]; [email protected]; [email protected]
Oggetto: [PATCH 06/13] USBATM: shutdown open connections when disconnected

This patch causes vcc_release_async to be applied to any open vcc's when the modem is disconnected. This signals a socket shutdown, letting the socket user know that the game is up. I wrote this patch because of reports that pppd would keep connections open forever when the modem is disconnected. This patch does not fix that problem, but it's a step in the right direction. It doesn't help because the pppoatm module doesn't yet monitor state changes on the ATM socket, so simply never realises that the ATM connection has gone down (meaning it doesn't tell the ppp layer). But at least there is a socket state change now.

Quoted 6 lines

Unfortunately this patch may create problems
for those rare users like me who use routed IP or some other non-ppp connection method that goes via the ATM ARP daemon: the daemon is buggy, and with this patch will crash when the modem is disconnected. Users with a buggy atmarpd can simply restart it after disconnecting the modem.

The problem is not only atmarpd, but also atmarp: it fails when establishing a PVC on a 'disconnected' VC, ie: a VC on and ADSL modem which didn't yet reach showtime.

CLIP and other protocols-over-ATM are designed to be connectionless. Thereby, you setup a CLIP connection, probably at systems startup, and forget about it: if a carrier is available, cells are exchanged, otherwise both parties discard outgoing cells. The connectionless design is one of the pros of CLIP with respect to, in example, PPPoA. It is not a con.

With this patch, the CLIP protocol becomes susceptible to connection status: it fails during setup if the ADSL modem is not yet at showtime (and who knows how long it will take to get it) and may discard the VC when the carrier happens to get lost after CLIP is started.

To my knowledge, no other ATM interface driver under Linux does reject a vcc open or a send due to the state of the physical carrier. Also note that there is not a per-interface instance of atmarpd and friends: they are scheduled systemwide and they may work at once on more interfaces. Making them die causes troubles not only to the outstanding network activity of the disconnected ADSL, but also to the one on other ATM interfaces.

pppd is designed to work both with connectionless (a cross-wire cable or an ATM VC) and connection-oriented carriers (a voice or ISDN modem): enabling its lcp echo feature usually is enough in order to detect a lost carrier. Out-of-sync peers state should be also detected. If it doesn't, it's pppd failure.

In summary, I'm not shure that the new USBATM behaviour is compatible with the (at least de-facto) actual standard of the Linux ATM stack. I'm not even shure that's compatible with ATM blueprints.

I'm however pretty shure that, when there is a patch that may impair and/or be incompatible with current software, the Linux end-user had always been provided with an option to disable the new feature and continue working the way it was used to.

I need that option.

Regards,

giampaolo

Quoted 3 lines
#12 lore raw

PATCH 7/13 USBATM: return correct error code when out of memory

In reply to Duncan Sands

We weren't always returning -ENOMEM.

drivers/usb/atm/usbatm.c +2 -0
Index: Linux/drivers/usb/atm/usbatm.c
===================================================================
@@ -1081,6 +1081,7 @@
 		urb = usb_alloc_urb(iso_packets, GFP_KERNEL);
 		if (!urb) {
 			dev_err(dev, "%s: no memory for urb %d!\n", __func__, i);
+			error = -ENOMEM;
 			goto fail_unbind;
 		}
 
@@ -1090,6 +1091,7 @@
 		buffer = kzalloc(channel->buf_size, GFP_KERNEL);
 		if (!buffer) {
 			dev_err(dev, "%s: no memory for buffer %d!\n", __func__, i);
+			error = -ENOMEM;
 			goto fail_unbind;
 		}
 
#13 lore raw

PATCH 8/13 USBATM: use dev_kfree_skb_any rather than dev_kfree_skb

In reply to Duncan Sands

In one spot (usbatm_cancel_send) we were calling dev_kfree_skb with irqs disabled. This mistake is just too easy to make, so systematically use dev_kfree_skb_any rather than dev_kfree_skb.

drivers/usb/atm/usbatm.c +3 -2
Index: Linux/drivers/usb/atm/usbatm.c
===================================================================
@@ -72,6 +72,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/moduleparam.h>
+#include <linux/netdevice.h>
 #include <linux/proc_fs.h>
 #include <linux/sched.h>
 #include <linux/signal.h>
@@ -199,7 +200,7 @@
 	if (vcc->pop)
 		vcc->pop(vcc, skb);
 	else
-		dev_kfree_skb(skb);
+		dev_kfree_skb_any(skb);
 }
 
 
@@ -397,7 +398,7 @@
 			if (!atm_charge(vcc, skb->truesize)) {
 				atm_rldbg(instance, "%s: failed atm_charge (skb->truesize: %u)!\n",
 						__func__, skb->truesize);
-				dev_kfree_skb(skb);
+				dev_kfree_skb_any(skb);
 				goto out;	/* atm_charge increments rx_drop */
 			}
 
#14 lore raw

PATCH 9/13 USBATM: measure buffer size in bytes; force valid sizes

In reply to Duncan Sands

Change the module parameters rcv_buf_size and snd_buf_size to specify buffer sizes in bytes rather than ATM cells. Since there is some danger that users may not notice this change, the parameters are renamed to rcv_buf_bytes etc. The transmit buffer needs to be a multiple of the ATM cell size in length, while the receive buffer should be a multiple of the endpoint maxpacket size (this wasn't enforced before, which causes trouble with isochronous transfers), so enforce these restrictions. Now that the usbatm probe method inspects the endpoint maxpacket size, minidriver bind routines need to set the correct alternate setting for the interface in their bind routine. This is the reason for the speedtch changes.

drivers/usb/atm/usbatm.c +59 -31
Index: Linux/drivers/usb/atm/usbatm.c
===================================================================
@@ -99,12 +99,11 @@
 
 #define UDSL_MAX_RCV_URBS		16
 #define UDSL_MAX_SND_URBS		16
-#define UDSL_MAX_RCV_BUF_SIZE		1024	/* ATM cells */
-#define UDSL_MAX_SND_BUF_SIZE		1024	/* ATM cells */
+#define UDSL_MAX_BUF_SIZE		64 * 1024	/* bytes */
 #define UDSL_DEFAULT_RCV_URBS		4
 #define UDSL_DEFAULT_SND_URBS		4
-#define UDSL_DEFAULT_RCV_BUF_SIZE	64	/* ATM cells */
-#define UDSL_DEFAULT_SND_BUF_SIZE	64	/* ATM cells */
+#define UDSL_DEFAULT_RCV_BUF_SIZE	64 * ATM_CELL_SIZE	/* bytes */
+#define UDSL_DEFAULT_SND_BUF_SIZE	64 * ATM_CELL_SIZE	/* bytes */
 
 #define ATM_CELL_HEADER			(ATM_CELL_SIZE - ATM_CELL_PAYLOAD)
 
@@ -112,8 +111,8 @@
 
 static unsigned int num_rcv_urbs = UDSL_DEFAULT_RCV_URBS;
 static unsigned int num_snd_urbs = UDSL_DEFAULT_SND_URBS;
-static unsigned int rcv_buf_size = UDSL_DEFAULT_RCV_BUF_SIZE;
-static unsigned int snd_buf_size = UDSL_DEFAULT_SND_BUF_SIZE;
+static unsigned int rcv_buf_bytes = UDSL_DEFAULT_RCV_BUF_SIZE;
+static unsigned int snd_buf_bytes = UDSL_DEFAULT_SND_BUF_SIZE;
 
 module_param(num_rcv_urbs, uint, S_IRUGO);
 MODULE_PARM_DESC(num_rcv_urbs,
@@ -127,15 +126,15 @@
 		 __MODULE_STRING(UDSL_MAX_SND_URBS) ", default: "
 		 __MODULE_STRING(UDSL_DEFAULT_SND_URBS) ")");
 
-module_param(rcv_buf_size, uint, S_IRUGO);
-MODULE_PARM_DESC(rcv_buf_size,
-		 "Size of the buffers used for reception in ATM cells (range: 1-"
-		 __MODULE_STRING(UDSL_MAX_RCV_BUF_SIZE) ", default: "
+module_param(rcv_buf_bytes, uint, S_IRUGO);
+MODULE_PARM_DESC(rcv_buf_bytes,
+		 "Size of the buffers used for reception, in bytes (range: 1-"
+		 __MODULE_STRING(UDSL_MAX_BUF_SIZE) ", default: "
 		 __MODULE_STRING(UDSL_DEFAULT_RCV_BUF_SIZE) ")");
 
-module_param(snd_buf_size, uint, S_IRUGO);
-MODULE_PARM_DESC(snd_buf_size,
-		 "Size of the buffers used for transmission in ATM cells (range: 1-"
+module_param(snd_buf_bytes, uint, S_IRUGO);
+MODULE_PARM_DESC(snd_buf_bytes,
+		 "Size of the buffers used for transmission, in bytes (range: 1-"
 		 __MODULE_STRING(UDSL_MAX_SND_BUF_SIZE) ", default: "
 		 __MODULE_STRING(UDSL_DEFAULT_SND_BUF_SIZE) ")");
 
@@ -430,14 +429,14 @@
 {
 	struct usbatm_control *ctrl = UDSL_SKB(skb);
 	struct atm_vcc *vcc = ctrl->atm.vcc;
-	unsigned int num_written;
+	unsigned int bytes_written;
 	unsigned int stride = instance->tx_channel.stride;
 
 	vdbg("%s: skb->len=%d, avail_space=%u", __func__, skb->len, avail_space);
 	UDSL_ASSERT(!(avail_space % stride));
 
-	for (num_written = 0; num_written < avail_space && ctrl->len;
-	     num_written += stride, target += stride) {
+	for (bytes_written = 0; bytes_written < avail_space && ctrl->len;
+	     bytes_written += stride, target += stride) {
 		unsigned int data_len = min_t(unsigned int, skb->len, ATM_CELL_PAYLOAD);
 		unsigned int left = ATM_CELL_PAYLOAD - data_len;
 		u8 *ptr = target;
@@ -480,7 +479,7 @@
 			ctrl->crc = crc32_be(ctrl->crc, ptr, left);
 	}
 
-	return num_written;
+	return bytes_written;
 }
 
 
@@ -524,7 +523,7 @@
 	struct sk_buff *skb = instance->current_skb;
 	struct urb *urb = NULL;
 	const unsigned int buf_size = instance->tx_channel.buf_size;
-	unsigned int num_written = 0;
+	unsigned int bytes_written = 0;
 	u8 *buffer = NULL;
 
 	if (!skb)
@@ -536,16 +535,16 @@
 			if (!urb)
 				break;		/* no more senders */
 			buffer = urb->transfer_buffer;
-			num_written = (urb->status == -EAGAIN) ?
+			bytes_written = (urb->status == -EAGAIN) ?
 				urb->transfer_buffer_length : 0;
 		}
 
-		num_written += usbatm_write_cells(instance, skb,
-						  buffer + num_written,
-						  buf_size - num_written);
+		bytes_written += usbatm_write_cells(instance, skb,
+						  buffer + bytes_written,
+						  buf_size - bytes_written);
 
 		vdbg("%s: wrote %u bytes from skb 0x%p to urb 0x%p",
-		     __func__, num_written, skb, urb);
+		     __func__, bytes_written, skb, urb);
 
 		if (!UDSL_SKB(skb)->len) {
 			struct atm_vcc *vcc = UDSL_SKB(skb)->atm.vcc;
@@ -556,8 +555,8 @@
 			skb = skb_dequeue(&instance->sndqueue);
 		}
 
-		if (num_written == buf_size || (!skb && num_written)) {
-			urb->transfer_buffer_length = num_written;
+		if (bytes_written == buf_size || (!skb && bytes_written)) {
+			urb->transfer_buffer_length = bytes_written;
 
 			if (usbatm_submit_urb(urb))
 				break;
@@ -990,6 +989,7 @@
 	char *buf;
 	int error = -ENOMEM;
 	int i, length;
+	unsigned int maxpacket, num_packets;
 
 	dev_dbg(dev, "%s: trying driver %s with vendor=%04x, product=%04x, ifnum %2d\n",
 			__func__, driver->driver_name,
@@ -1058,10 +1058,38 @@
 	instance->tx_channel.endpoint = usb_sndbulkpipe(usb_dev, driver->out);
 	instance->rx_channel.stride = ATM_CELL_SIZE + driver->rx_padding;
 	instance->tx_channel.stride = ATM_CELL_SIZE + driver->tx_padding;
-	instance->rx_channel.buf_size = rcv_buf_size * instance->rx_channel.stride;
-	instance->tx_channel.buf_size = snd_buf_size * instance->tx_channel.stride;
 	instance->rx_channel.usbatm = instance->tx_channel.usbatm = instance;
 
+	/* tx buffer size must be a positive multiple of the stride */
+	instance->tx_channel.buf_size = max (instance->tx_channel.stride,
+			snd_buf_bytes - (snd_buf_bytes % instance->tx_channel.stride));
+
+	/* rx buffer size must be a positive multiple of the endpoint maxpacket */
+	maxpacket = usb_maxpacket(usb_dev, instance->rx_channel.endpoint, 0);
+
+	if ((maxpacket < 1) || (maxpacket > UDSL_MAX_BUF_SIZE)) {
+		dev_err(dev, "%s: invalid endpoint %02x!\n", __func__,
+				usb_pipeendpoint(instance->rx_channel.endpoint));
+		error = -EINVAL;
+		goto fail_unbind;
+	}
+
+	num_packets = max (1U, (rcv_buf_bytes + maxpacket / 2) / maxpacket); /* round */
+
+	if (num_packets * maxpacket > UDSL_MAX_BUF_SIZE)
+		num_packets--;
+
+	instance->rx_channel.buf_size = num_packets * maxpacket;
+
+#ifdef DEBUG
+	for (i = 0; i < 2; i++) {
+		struct usbatm_channel *channel = i ?
+			&instance->tx_channel : &instance->rx_channel;
+
+		dev_dbg(dev, "%s: using %d byte buffer for %s channel 0x%p\n", __func__, channel->buf_size, i ? "tx" : "rx", channel);
+	}
+#endif
+
 	skb_queue_head_init(&instance->sndqueue);
 
 	for (i = 0; i < num_rcv_urbs + num_snd_urbs; i++) {
@@ -1232,10 +1260,10 @@
 
 	if ((num_rcv_urbs > UDSL_MAX_RCV_URBS)
 	    || (num_snd_urbs > UDSL_MAX_SND_URBS)
-	    || (rcv_buf_size < 1)
-	    || (rcv_buf_size > UDSL_MAX_RCV_BUF_SIZE)
-	    || (snd_buf_size < 1)
-	    || (snd_buf_size > UDSL_MAX_SND_BUF_SIZE))
+	    || (rcv_buf_bytes < 1)
+	    || (rcv_buf_bytes > UDSL_MAX_BUF_SIZE)
+	    || (snd_buf_bytes < 1)
+	    || (snd_buf_bytes > UDSL_MAX_BUF_SIZE))
 		return -EINVAL;
 
 	return 0;
drivers/usb/atm/speedtch.c +25 -5
Index: Linux/drivers/usb/atm/speedtch.c
===================================================================
@@ -89,6 +89,7 @@
 		 "Enable software buffering (default: "
 		 __MODULE_STRING(DEFAULT_SW_BUFFERING) ")");
 
+#define INTERFACE_DATA		1
 #define ENDPOINT_INT		0x81
 #define ENDPOINT_DATA		0x07
 #define ENDPOINT_FIRMWARE	0x05
@@ -98,6 +99,8 @@
 struct speedtch_instance_data {
 	struct usbatm_data *usbatm;
 
+	unsigned int altsetting;
+
 	struct work_struct status_checker;
 
 	unsigned char last_status;
@@ -270,6 +273,11 @@
 	   because we're in our own kernel thread anyway. */
 	msleep_interruptible(1000);
 
+	if ((ret = usb_set_interface(usb_dev, INTERFACE_DATA, instance->altsetting)) < 0) {
+		usb_err(usbatm, "%s: setting interface to %d failed (%d)!\n", __func__, instance->altsetting, ret);
+		goto out_free;
+	}
+
 	/* Enable software buffering, if requested */
 	if (sw_buffering)
 		speedtch_set_swbuff(instance, 1);
@@ -586,11 +594,6 @@
 
 	atm_dbg(usbatm, "%s entered\n", __func__);
 
-	if ((ret = usb_set_interface(usb_dev, 1, altsetting)) < 0) {
-		atm_dbg(usbatm, "%s: usb_set_interface returned %d!\n", __func__, ret);
-		return ret;
-	}
-
 	/* Set MAC address, it is stored in the serial number */
 	memset(atm_dev->esi, 0, sizeof(atm_dev->esi));
 	if (usb_string(usb_dev, usb_dev->descriptor.iSerialNumber, mac_str, sizeof(mac_str)) == 12) {
@@ -725,6 +728,23 @@
 
 	instance->usbatm = usbatm;
 
+	/* altsetting may change at any moment, so take a snapshot */
+	instance->altsetting = altsetting;
+
+	if (instance->altsetting)
+		if ((ret = usb_set_interface(usb_dev, INTERFACE_DATA, instance->altsetting)) < 0) {
+			usb_err(usbatm, "%s: setting interface to %2d failed (%d)!\n", __func__, instance->altsetting, ret);
+			instance->altsetting = 0; /* fall back to default */
+		}
+
+	if (!instance->altsetting) {
+		if ((ret = usb_set_interface(usb_dev, INTERFACE_DATA, DEFAULT_ALTSETTING)) < 0) {
+			usb_err(usbatm, "%s: setting interface to %2d failed (%d)!\n", __func__, DEFAULT_ALTSETTING, ret);
+			goto fail_free;
+		}
+		instance->altsetting = DEFAULT_ALTSETTING;
+	}
+
 	INIT_WORK(&instance->status_checker, (void *)speedtch_check_status, instance);
 
 	instance->status_checker.timer.function = speedtch_status_poll;
#15 lore raw

PATCH 10/13 USBATM: allow isochronous transfer

In reply to Duncan Sands

While the usbatm core has had some support for using isoc urbs for some time, there was no way for users to turn it on. While use of isoc transfer should still be considered experimental, it now works well enough to let users turn it on. Minidrivers signal to the core that they want to use isoc transfer by setting the new UDSL_USE_ISOC flag. The speedtch minidriver gets a new module parameter enable_isoc (defaults to false), plus some logic that checks for the existence of an isoc receive endpoint (not all speedtouch modems have one).

drivers/usb/atm/cxacru.c +2 -2
Index: Linux/drivers/usb/atm/cxacru.c
===================================================================
@@ -836,8 +836,8 @@
 	.heavy_init	= cxacru_heavy_init,
 	.unbind		= cxacru_unbind,
 	.atm_start	= cxacru_atm_start,
-	.in		= CXACRU_EP_DATA,
-	.out		= CXACRU_EP_DATA,
+	.bulk_in	= CXACRU_EP_DATA,
+	.bulk_out	= CXACRU_EP_DATA,
 	.rx_padding	= 3,
 	.tx_padding	= 11,
 };
drivers/usb/atm/speedtch.c +66 -16

157 lines not on this page · raw message

drivers/usb/atm/ueagle-atm.c +2 -2
Index: Linux/drivers/usb/atm/ueagle-atm.c
===================================================================
@@ -1705,8 +1705,8 @@
 	.atm_start = uea_atm_open,
 	.unbind = uea_unbind,
 	.heavy_init = uea_heavy,
-	.in = UEA_BULK_DATA_PIPE,
-	.out = UEA_BULK_DATA_PIPE,
+	.bulk_in = UEA_BULK_DATA_PIPE,
+	.bulk_out = UEA_BULK_DATA_PIPE,
 };
 
 static int uea_probe(struct usb_interface *intf, const struct usb_device_id *id)
drivers/usb/atm/usbatm.c +15 -15
Index: Linux/drivers/usb/atm/usbatm.c
===================================================================
@@ -1049,17 +1049,23 @@
 	init_completion(&instance->thread_exited);
 
 	INIT_LIST_HEAD(&instance->vcc_list);
+	skb_queue_head_init(&instance->sndqueue);
 
 	usbatm_init_channel(&instance->rx_channel);
 	usbatm_init_channel(&instance->tx_channel);
 	tasklet_init(&instance->rx_channel.tasklet, usbatm_rx_process, (unsigned long)instance);
 	tasklet_init(&instance->tx_channel.tasklet, usbatm_tx_process, (unsigned long)instance);
-	instance->rx_channel.endpoint = usb_rcvbulkpipe(usb_dev, driver->in);
-	instance->tx_channel.endpoint = usb_sndbulkpipe(usb_dev, driver->out);
 	instance->rx_channel.stride = ATM_CELL_SIZE + driver->rx_padding;
 	instance->tx_channel.stride = ATM_CELL_SIZE + driver->tx_padding;
 	instance->rx_channel.usbatm = instance->tx_channel.usbatm = instance;
 
+	if ((instance->flags & UDSL_USE_ISOC) && driver->isoc_in)
+		instance->rx_channel.endpoint = usb_rcvisocpipe(usb_dev, driver->isoc_in);
+	else
+		instance->rx_channel.endpoint = usb_rcvbulkpipe(usb_dev, driver->bulk_in);
+
+	instance->tx_channel.endpoint = usb_sndbulkpipe(usb_dev, driver->bulk_out);
+
 	/* tx buffer size must be a positive multiple of the stride */
 	instance->tx_channel.buf_size = max (instance->tx_channel.stride,
 			snd_buf_bytes - (snd_buf_bytes % instance->tx_channel.stride));
@@ -1080,6 +1086,7 @@
 		num_packets--;
 
 	instance->rx_channel.buf_size = num_packets * maxpacket;
+	instance->rx_channel.packet_size = maxpacket;
 
 #ifdef DEBUG
 	for (i = 0; i < 2; i++) {
@@ -1090,22 +1097,16 @@
 	}
 #endif
 
-	skb_queue_head_init(&instance->sndqueue);
+	/* initialize urbs */
 
 	for (i = 0; i < num_rcv_urbs + num_snd_urbs; i++) {
-		struct urb *urb;
 		u8 *buffer;
-		unsigned int iso_packets = 0, iso_size = 0;
 		struct usbatm_channel *channel = i < num_rcv_urbs ?
 			&instance->rx_channel : &instance->tx_channel;
+		struct urb *urb;
+		unsigned int iso_packets = usb_pipeisoc(channel->endpoint) ? channel->buf_size / channel->packet_size : 0;
 
-		if (usb_pipeisoc(channel->endpoint)) {
-			/* don't expect iso out endpoints */
-			iso_size = usb_maxpacket(instance->usb_dev, channel->endpoint, 0);
-			iso_size -= iso_size % channel->stride;	/* alignment */
-			BUG_ON(!iso_size);
-			iso_packets = (channel->buf_size - 1) / iso_size + 1;
-		}
+		UDSL_ASSERT(!usb_pipeisoc(channel->endpoint) || usb_pipein(channel->endpoint));
 
 		urb = usb_alloc_urb(iso_packets, GFP_KERNEL);
 		if (!urb) {
@@ -1132,9 +1133,8 @@
 			urb->transfer_flags = URB_ISO_ASAP;
 			urb->number_of_packets = iso_packets;
 			for (j = 0; j < iso_packets; j++) {
-				urb->iso_frame_desc[j].offset = iso_size * j;
-				urb->iso_frame_desc[j].length = min_t(int, iso_size,
-								      channel->buf_size - urb->iso_frame_desc[j].offset);
+				urb->iso_frame_desc[j].offset = channel->packet_size * j;
+				urb->iso_frame_desc[j].length = channel->packet_size;
 			}
 		}
 
drivers/usb/atm/usbatm.h +5 -2
Index: Linux/drivers/usb/atm/usbatm.h
===================================================================
@@ -87,6 +87,7 @@
 /* flags, set by mini-driver in bind() */
 
 #define UDSL_SKIP_HEAVY_INIT	(1<<0)
+#define UDSL_USE_ISOC		(1<<1)
 
 
 /* mini driver */
@@ -118,8 +119,9 @@
 	/* cleanup ATM device ... can sleep, but can't fail */
 	void (*atm_stop) (struct usbatm_data *, struct atm_dev *);
 
-        int in;		/* rx endpoint */
-        int out;	/* tx endpoint */
+        int bulk_in;	/* bulk rx endpoint */
+        int isoc_in;	/* isochronous rx endpoint */
+        int bulk_out;	/* bulk tx endpoint */
 
 	unsigned rx_padding;
 	unsigned tx_padding;
@@ -134,6 +136,7 @@
 	int endpoint;			/* usb pipe */
 	unsigned int stride;		/* ATM cell size + padding */
 	unsigned int buf_size;		/* urb buffer size */
+	unsigned int packet_size;	/* endpoint maxpacket */
 	spinlock_t lock;
 	struct list_head list;
 	struct tasklet_struct tasklet;
drivers/usb/atm/xusbatm.c +2 -2
Index: Linux/drivers/usb/atm/xusbatm.c
===================================================================
@@ -210,8 +210,8 @@
 		xusbatm_drivers[i].bind		= xusbatm_bind;
 		xusbatm_drivers[i].unbind	= xusbatm_unbind;
 		xusbatm_drivers[i].atm_start	= xusbatm_atm_start;
-		xusbatm_drivers[i].in		= rx_endpoint[i];
-		xusbatm_drivers[i].out		= tx_endpoint[i];
+		xusbatm_drivers[i].bulk_in	= rx_endpoint[i];
+		xusbatm_drivers[i].bulk_out	= tx_endpoint[i];
 		xusbatm_drivers[i].rx_padding	= rx_padding[i];
 		xusbatm_drivers[i].tx_padding	= tx_padding[i];
 	}
#16 lore raw

PATCH 11/13 USBATM: handle urbs containing partial cells

In reply to Duncan Sands

The receive logic has always assumed that urbs contain an integral number of ATM cells, which is a bit naughty, though it never caused any problems with bulk transfers. Isochronous urbs spank us soundly for this. Fixed thanks to this patch, mostly by Stanislaw Gruszka.

drivers/usb/atm/usbatm.c +177 -98
Index: Linux/drivers/usb/atm/usbatm.c
===================================================================
@@ -296,126 +296,159 @@
 	return NULL;
 }
 
-static void usbatm_extract_cells(struct usbatm_data *instance,
-			       unsigned char *source, unsigned int avail_data)
+static void usbatm_extract_one_cell(struct usbatm_data *instance, unsigned char *source)
 {
-	struct usbatm_vcc_data *cached_vcc = NULL;
 	struct atm_vcc *vcc;
 	struct sk_buff *sarb;
-	unsigned int stride = instance->rx_channel.stride;
-	int vci, cached_vci = 0;
-	short vpi, cached_vpi = 0;
-	u8 pti;
+	short vpi = ((source[0] & 0x0f) << 4)  | (source[1] >> 4);
+	int vci = ((source[1] & 0x0f) << 12) | (source[2] << 4) | (source[3] >> 4);
+	u8 pti = ((source[3] & 0xe) >> 1);
 
-	for (; avail_data >= stride; avail_data -= stride, source += stride) {
-		vpi = ((source[0] & 0x0f) << 4)  | (source[1] >> 4);
-		vci = ((source[1] & 0x0f) << 12) | (source[2] << 4) | (source[3] >> 4);
-		pti = ((source[3] & 0xe) >> 1);
+	vdbg("%s: vpi %hd, vci %d, pti %d", __func__, vpi, vci, pti);
 
-		vdbg("%s: vpi %hd, vci %d, pti %d", __func__, vpi, vci, pti);
+	if ((vci != instance->cached_vci) || (vpi != instance->cached_vpi)) {
+		instance->cached_vpi = vpi;
+		instance->cached_vci = vci;
 
-		if ((vci != cached_vci) || (vpi != cached_vpi)) {
-			cached_vpi = vpi;
-			cached_vci = vci;
+		instance->cached_vcc = usbatm_find_vcc(instance, vpi, vci);
 
-			cached_vcc = usbatm_find_vcc(instance, vpi, vci);
+		if (!instance->cached_vcc)
+			atm_rldbg(instance, "%s: unknown vpi/vci (%hd/%d)!\n", __func__, vpi, vci);
+	}
 
-			if (!cached_vcc)
-				atm_rldbg(instance, "%s: unknown vpi/vci (%hd/%d)!\n", __func__, vpi, vci);
-		}
+	if (!instance->cached_vcc)
+		return;
 
-		if (!cached_vcc)
-			continue;
+	vcc = instance->cached_vcc->vcc;
 
-		vcc = cached_vcc->vcc;
+	/* OAM F5 end-to-end */
+	if (pti == ATM_PTI_E2EF5) {
+		if (printk_ratelimit())
+			atm_warn(instance, "%s: OAM not supported (vpi %d, vci %d)!\n",
+				__func__, vpi, vci);
+		atomic_inc(&vcc->stats->rx_err);
+		return;
+	}
 
-		/* OAM F5 end-to-end */
-		if (pti == ATM_PTI_E2EF5) {
-			if (printk_ratelimit())
-				atm_warn(instance, "%s: OAM not supported (vpi %d, vci %d)!\n",
-					__func__, vpi, vci);
+	sarb = instance->cached_vcc->sarb;
+
+	if (sarb->tail + ATM_CELL_PAYLOAD > sarb->end) {
+		atm_rldbg(instance, "%s: buffer overrun (sarb->len %u, vcc: 0x%p)!\n",
+				__func__, sarb->len, vcc);
+		/* discard cells already received */
+		skb_trim(sarb, 0);
+		UDSL_ASSERT(sarb->tail + ATM_CELL_PAYLOAD <= sarb->end);
+	}
+
+	memcpy(sarb->tail, source + ATM_CELL_HEADER, ATM_CELL_PAYLOAD);
+	__skb_put(sarb, ATM_CELL_PAYLOAD);
+
+	if (pti & 1) {
+		struct sk_buff *skb;
+		unsigned int length;
+		unsigned int pdu_length;
+
+		length = (source[ATM_CELL_SIZE - 6] << 8) + source[ATM_CELL_SIZE - 5];
+
+		/* guard against overflow */
+		if (length > ATM_MAX_AAL5_PDU) {
+			atm_rldbg(instance, "%s: bogus length %u (vcc: 0x%p)!\n",
+				  __func__, length, vcc);
 			atomic_inc(&vcc->stats->rx_err);
-			continue;
+			goto out;
 		}
 
-		sarb = cached_vcc->sarb;
+		pdu_length = usbatm_pdu_length(length);
 
-		if (sarb->tail + ATM_CELL_PAYLOAD > sarb->end) {
-			atm_rldbg(instance, "%s: buffer overrun (sarb->len %u, vcc: 0x%p)!\n",
-					__func__, sarb->len, vcc);
-			/* discard cells already received */
-			skb_trim(sarb, 0);
-			UDSL_ASSERT(sarb->tail + ATM_CELL_PAYLOAD <= sarb->end);
-		}
-
-		memcpy(sarb->tail, source + ATM_CELL_HEADER, ATM_CELL_PAYLOAD);
-		__skb_put(sarb, ATM_CELL_PAYLOAD);
-
-		if (pti & 1) {
-			struct sk_buff *skb;
-			unsigned int length;
-			unsigned int pdu_length;
-
-			length = (source[ATM_CELL_SIZE - 6] << 8) + source[ATM_CELL_SIZE - 5];
-
-			/* guard against overflow */
-			if (length > ATM_MAX_AAL5_PDU) {
-				atm_rldbg(instance, "%s: bogus length %u (vcc: 0x%p)!\n",
-						__func__, length, vcc);
-				atomic_inc(&vcc->stats->rx_err);
-				goto out;
-			}
+		if (sarb->len < pdu_length) {
+			atm_rldbg(instance, "%s: bogus pdu_length %u (sarb->len: %u, vcc: 0x%p)!\n",
+				  __func__, pdu_length, sarb->len, vcc);
+			atomic_inc(&vcc->stats->rx_err);
+			goto out;
+		}
 
-			pdu_length = usbatm_pdu_length(length);
+		if (crc32_be(~0, sarb->tail - pdu_length, pdu_length) != 0xc704dd7b) {
+			atm_rldbg(instance, "%s: packet failed crc check (vcc: 0x%p)!\n",
+				  __func__, vcc);
+			atomic_inc(&vcc->stats->rx_err);
+			goto out;
+		}
 
-			if (sarb->len < pdu_length) {
-				atm_rldbg(instance, "%s: bogus pdu_length %u (sarb->len: %u, vcc: 0x%p)!\n",
-						__func__, pdu_length, sarb->len, vcc);
-				atomic_inc(&vcc->stats->rx_err);
-				goto out;
-			}
+		vdbg("%s: got packet (length: %u, pdu_length: %u, vcc: 0x%p)", __func__, length, pdu_length, vcc);
 
-			if (crc32_be(~0, sarb->tail - pdu_length, pdu_length) != 0xc704dd7b) {
-				atm_rldbg(instance, "%s: packet failed crc check (vcc: 0x%p)!\n",
-						__func__, vcc);
-				atomic_inc(&vcc->stats->rx_err);
-				goto out;
-			}
+		if (!(skb = dev_alloc_skb(length))) {
+			if (printk_ratelimit())
+				atm_err(instance, "%s: no memory for skb (length: %u)!\n",
+					__func__, length);
+			atomic_inc(&vcc->stats->rx_drop);
+			goto out;
+		}
 
-			vdbg("%s: got packet (length: %u, pdu_length: %u, vcc: 0x%p)", __func__, length, pdu_length, vcc);
+		vdbg("%s: allocated new sk_buff (skb: 0x%p, skb->truesize: %u)", __func__, skb, skb->truesize);
 
-			if (!(skb = dev_alloc_skb(length))) {
-				if (printk_ratelimit())
-					atm_err(instance, "%s: no memory for skb (length: %u)!\n",
-							__func__, length);
-				atomic_inc(&vcc->stats->rx_drop);
-				goto out;
-			}
+		if (!atm_charge(vcc, skb->truesize)) {
+			atm_rldbg(instance, "%s: failed atm_charge (skb->truesize: %u)!\n",
+				  __func__, skb->truesize);
+			dev_kfree_skb_any(skb);
+			goto out;	/* atm_charge increments rx_drop */
+		}
 
-			vdbg("%s: allocated new sk_buff (skb: 0x%p, skb->truesize: %u)", __func__, skb, skb->truesize);
+		memcpy(skb->data, sarb->tail - pdu_length, length);
+		__skb_put(skb, length);
 
-			if (!atm_charge(vcc, skb->truesize)) {
-				atm_rldbg(instance, "%s: failed atm_charge (skb->truesize: %u)!\n",
-						__func__, skb->truesize);
-				dev_kfree_skb_any(skb);
-				goto out;	/* atm_charge increments rx_drop */
-			}
+		vdbg("%s: sending skb 0x%p, skb->len %u, skb->truesize %u",
+		     __func__, skb, skb->len, skb->truesize);
 
-			memcpy(skb->data, sarb->tail - pdu_length, length);
-			__skb_put(skb, length);
+		PACKETDEBUG(skb->data, skb->len);
 
-			vdbg("%s: sending skb 0x%p, skb->len %u, skb->truesize %u",
-			     __func__, skb, skb->len, skb->truesize);
+		vcc->push(vcc, skb);
 
-			PACKETDEBUG(skb->data, skb->len);
+		atomic_inc(&vcc->stats->rx);
+	out:
+		skb_trim(sarb, 0);
+	}
+}
 
-			vcc->push(vcc, skb);
+static void usbatm_extract_cells(struct usbatm_data *instance,
+		unsigned char *source, unsigned int avail_data)
+{
+	unsigned int stride = instance->rx_channel.stride;
+	unsigned int buf_usage = instance->buf_usage;
 
-			atomic_inc(&vcc->stats->rx);
-		out:
-			skb_trim(sarb, 0);
+	/* extract cells from incoming data, taking into account that
+	 * the length of avail data may not be a multiple of stride */
+
+	if (buf_usage > 0) {
+		/* we have a partially received atm cell */
+		unsigned char *cell_buf = instance->cell_buf;
+		unsigned int space_left = stride - buf_usage;
+
+		UDSL_ASSERT(buf_usage <= stride);
+
+		if (avail_data >= space_left) {
+			/* add new data and process cell */
+			memcpy(cell_buf + buf_usage, source, space_left);
+			source += space_left;
+			avail_data -= space_left;
+			usbatm_extract_one_cell(instance, cell_buf);
+			instance->buf_usage = 0;
+		} else {
+			/* not enough data to fill the cell */
+			memcpy(cell_buf + buf_usage, source, avail_data);
+			instance->buf_usage = buf_usage + avail_data;
+			return;
 		}
 	}
+
+	for (; avail_data >= stride; avail_data -= stride, source += stride)
+		usbatm_extract_one_cell(instance, source);
+
+	if (avail_data > 0) {
+		/* length was not a multiple of stride -
+		 * save remaining data for next call */
+		memcpy(instance->cell_buf, source, avail_data);
+		instance->buf_usage = avail_data;
+	}
 }
 
 
@@ -496,16 +529,40 @@
 		vdbg("%s: processing urb 0x%p", __func__, urb);
 
 		if (usb_pipeisoc(urb->pipe)) {
+			unsigned char *merge_start = NULL;
+			unsigned int merge_length = 0;
+			const unsigned int packet_size = instance->rx_channel.packet_size;
 			int i;
-			for (i = 0; i < urb->number_of_packets; i++)
-				if (!urb->iso_frame_desc[i].status)
-					usbatm_extract_cells(instance,
-							     (u8 *)urb->transfer_buffer + urb->iso_frame_desc[i].offset,
-							     urb->iso_frame_desc[i].actual_length);
-		}
-		else
+
+			for (i = 0; i < urb->number_of_packets; i++) {
+				if (!urb->iso_frame_desc[i].status) {
+					unsigned int actual_length = urb->iso_frame_desc[i].actual_length;
+
+					UDSL_ASSERT(actual_length <= packet_size);
+
+					if (!merge_length)
+						merge_start = (unsigned char *)urb->transfer_buffer + urb->iso_frame_desc[i].offset;
+					merge_length += actual_length;
+					if (merge_length && (actual_length < packet_size)) {
+						usbatm_extract_cells(instance, merge_start, merge_length);
+						merge_length = 0;
+					}
+				} else {
+					atm_rldbg(instance, "%s: status %d in frame %d!\n", __func__, urb->status, i);
+					if (merge_length)
+						usbatm_extract_cells(instance, merge_start, merge_length);
+					merge_length = 0;
+					instance->buf_usage = 0;
+				}
+			}
+
+			if (merge_length)
+				usbatm_extract_cells(instance, merge_start, merge_length);
+		} else
 			if (!urb->status)
 				usbatm_extract_cells(instance, urb->transfer_buffer, urb->actual_length);
+			else
+				instance->buf_usage = 0;
 
 		if (usbatm_submit_urb(urb))
 			return;
@@ -797,6 +854,9 @@
 	vcc->dev_data = new;
 
 	tasklet_disable(&instance->rx_channel.tasklet);
+	instance->cached_vcc = new;
+	instance->cached_vpi = vpi;
+	instance->cached_vci = vci;
 	list_add(&new->list, &instance->vcc_list);
 	tasklet_enable(&instance->rx_channel.tasklet);
 
@@ -836,6 +896,11 @@
 	down(&instance->serialize);	/* vs self, usbatm_atm_open, usbatm_usb_disconnect */
 
 	tasklet_disable(&instance->rx_channel.tasklet);
+	if (instance->cached_vcc == vcc_data) {
+		instance->cached_vcc = NULL;
+		instance->cached_vpi = ATM_VPI_UNSPEC;
+		instance->cached_vci = ATM_VCI_UNSPEC;
+	}
 	list_del(&vcc_data->list);
 	tasklet_enable(&instance->rx_channel.tasklet);
 
@@ -1146,6 +1211,16 @@
 		     __func__, urb->transfer_buffer, urb->transfer_buffer_length, urb);
 	}
 
+	instance->cached_vpi = ATM_VPI_UNSPEC;
+	instance->cached_vci = ATM_VCI_UNSPEC;
+	instance->cell_buf = kmalloc(instance->rx_channel.stride, GFP_KERNEL);
+
+	if (!instance->cell_buf) {
+		dev_err(dev, "%s: no memory for cell buffer!\n", __func__);
+		error = -ENOMEM;
+		goto fail_unbind;
+	}
+
 	if (!(instance->flags & UDSL_SKIP_HEAVY_INIT) && driver->heavy_init) {
 		error = usbatm_heavy_init(instance);
 	} else {
@@ -1165,6 +1240,8 @@
 	if (instance->driver->unbind)
 		instance->driver->unbind(instance, intf);
  fail_free:
+	kfree(instance->cell_buf);
+
 	for (i = 0; i < num_rcv_urbs + num_snd_urbs; i++) {
 		if (instance->urbs[i])
 			kfree(instance->urbs[i]->transfer_buffer);
@@ -1236,6 +1313,8 @@
 		usb_free_urb(instance->urbs[i]);
 	}
 
+	kfree(instance->cell_buf);
+
 	/* ATM finalize */
 	if (instance->atm_dev)
 		atm_dev_deregister(instance->atm_dev);
drivers/usb/atm/usbatm.h +7 -0
Index: Linux/drivers/usb/atm/usbatm.h
===================================================================
@@ -187,6 +187,13 @@
 	struct sk_buff_head sndqueue;
 	struct sk_buff *current_skb;	/* being emptied */
 
+	struct usbatm_vcc_data *cached_vcc;
+	int cached_vci;
+	short cached_vpi;
+
+	unsigned char *cell_buf;	/* holds partial rx cell */
+	unsigned int buf_usage;
+
 	struct urb *urbs[0];
 };
 
#17 lore raw

PATCH 12/13 USBATM: bump version numbers

In reply to Duncan Sands
drivers/usb/atm/speedtch.c +1 -1
Index: Linux/drivers/usb/atm/speedtch.c
===================================================================
@@ -42,7 +42,7 @@
 #include "usbatm.h"
 
 #define DRIVER_AUTHOR	"Johan Verrept, Duncan Sands <[email protected]>"
-#define DRIVER_VERSION	"1.9"
+#define DRIVER_VERSION	"1.10"
 #define DRIVER_DESC	"Alcatel SpeedTouch USB driver version " DRIVER_VERSION
 
 static const char speedtch_driver_name[] = "speedtch";
drivers/usb/atm/usbatm.c +1 -1
Index: Linux/drivers/usb/atm/usbatm.c
===================================================================
@@ -92,7 +92,7 @@
 #endif
 
 #define DRIVER_AUTHOR	"Johan Verrept, Duncan Sands <[email protected]>"
-#define DRIVER_VERSION	"1.9"
+#define DRIVER_VERSION	"1.10"
 #define DRIVER_DESC	"Generic USB ATM/DSL I/O, version " DRIVER_VERSION
 
 static const char usbatm_driver_name[] = "usbatm";
#18 lore raw

PATCH 13/13 USBATM: -EILSEQ workaround

In reply to Duncan Sands

Don't throttle on -EILSEQ urb status if requested by a minidriver. It seems the ueagle modems are buggy, giving -EILSEQ when they have no data to send. The ueagle change will be sent separately by the ueagle guys. Patch by Matthieu Castet.

drivers/usb/atm/usbatm.c +4 -1
Index: Linux/drivers/usb/atm/usbatm.c
===================================================================
@@ -270,7 +270,10 @@
 
 	spin_unlock_irqrestore(&channel->lock, flags);
 
-	if (unlikely(urb->status)) {
+	if (unlikely(urb->status) &&
+			(!(channel->usbatm->flags & UDSL_IGNORE_EILSEQ) ||
+			 urb->status != -EILSEQ ))
+	{
 		if (printk_ratelimit())
 			atm_warn(channel->usbatm, "%s: urb 0x%p failed (%d)!\n",
 				__func__, urb, urb->status);
drivers/usb/atm/usbatm.h +1 -0
Index: Linux/drivers/usb/atm/usbatm.h
===================================================================
@@ -88,6 +88,7 @@
 
 #define UDSL_SKIP_HEAVY_INIT	(1<<0)
 #define UDSL_USE_ISOC		(1<<1)
+#define UDSL_IGNORE_EILSEQ	(1<<2)
 
 
 /* mini driver */