ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1
Subsystems (4)
Best regards to all and everyone. I just purchased a new RS480 (Radeon XPress200)-based motherboard. It is a Sapphire Pure Performance PP-A9RS480. Mine is equipped with an Athlon64 3200+. I am attaching the output of lspci -v
When booting with kernels from 2.6.15-rc1 up (tested with 2.6.15-rc1, 2.6.15-rc5, 2.6.15 and 2.6.16-rc1), the boot process freezes after displaying messages retated to registering io schedulers:
...
...
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
There is no OOPS of any kind. The disk activity led remains on. With both 2.6.14 and 2.6.14.6, boot regularly continues with:
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe ([email protected]) and [email protected]
nbd: registered device at major 43
...
...
I tried to enable all debug options in configure, but no new message appears.
Important: I obtain the same result (frozen after "io scheduler cfq registered") when booting with a 100MB netinst debian sid bootdisk, downloaded last night. An older (9 month old) Ubuntu bootdisk boots perfectly. Both cd's are AMD64-specific.
I will be very happy to provide any further info, or to make any test. Please CC me in your answers if you can.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
0000:00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01)
Subsystem: ATI Technologies Inc RS480 Host Bridge
Flags: bus master, 66MHz, medium devsel, latency 64
0000:00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5a3f (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 99 Bus: primary=00, secondary=01, subordinate=01, sec-latency=68 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000d8000000-00000000dff00000 Capabilities: <available only to root>
0000:00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ATI Technologies Inc ATI 437A Serial ATA Controller Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 5 I/O ports at ff00 [size=8] I/O ports at fe00 [size=4] I/O ports at fd00 [size=8] I/O ports at fc00 [size=4] I/O ports at fb00 [size=16] Memory at fe02f000 (32-bit, non-prefetchable) [size=512] Expansion ROM at 40000000 [disabled] [size=512K] Capabilities: <available only to root>
0000:00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ATI Technologies Inc ATI 4379 Serial ATA Controller Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10 I/O ports at fa00 [size=8] I/O ports at f900 [size=4] I/O ports at f800 [size=8] I/O ports at f700 [size=4] I/O ports at f600 [size=16] Memory at fe02e000 (32-bit, non-prefetchable) [size=512] Expansion ROM at 40080000 [disabled] [size=512K] Capabilities: <available only to root>
0000:00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI])
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
0000:00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI])
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
0000:00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (prog-if 20 [EHCI])
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
0000:00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 10)
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: 66MHz, medium devsel
I/O ports at 0400 [size=16]
Memory at fe02a000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <available only to root>
0000:00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI (prog-if 8a [Master SecP PriP])
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 64
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at f400 [size=16]
Capabilities: <available only to root>
0000:00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 0
0000:00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (prog-if 01 [Subtractive decode])
Flags: bus master, VGA palette snoop, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: fdc00000-fdcfffff
0000:00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller (rev 01)
Subsystem: PC Partner Limited: Unknown device 5215
Flags: bus master, 66MHz, slow devsel, latency 64, IRQ 11
Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: <available only to root>
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Flags: fast devsel
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Flags: fast devsel
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Flags: fast devsel
0000:01:05.0 VGA compatible controller: ATI Technologies Inc RS480 [Radeon Xpress 200G Series] (prog-if 00 [VGA])
Subsystem: PC Partner Limited: Unknown device 0a56 Flags: bus master, 66MHz, medium devsel, latency 255, IRQ 11 Memory at d8000000 (32-bit, prefetchable) [size=128M] I/O ports at ee00 [size=256] Memory at fdef0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fde00000 [disabled] [size=128K] Capabilities: <available only to root>
0000:01:05.1 Display controller: ATI Technologies Inc: Unknown device 5854
Subsystem: PC Partner Limited: Unknown device 0a57
Flags: 66MHz, medium devsel
Memory at <unassigned> (32-bit, prefetchable) [disabled] Memory at fde20000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: <available only to root>
0000:02:05.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Technotrend-Budget / Hauppauge WinTV-NOVA-S DVB card
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at fddff000 (32-bit, non-prefetchable) [size=512]
0000:02:06.0 Multimedia controller: Philips Semiconductors SAA7133 Video Broadcast Decoder (rev d0)
Subsystem: Pinnacle Systems Inc.: Unknown device 002e
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at fddfe000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <available only to root>
0000:02:07.0 SCSI storage controller: LSI Logic / Symbios Logic 53c810 (rev 23)
Subsystem: LSI Logic / Symbios Logic LSI53C810AE PCI to SCSI I/O Processor
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at da00 [size=256]
Memory at fddfd000 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>
0000:02:08.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 06)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Flags: bus master, slow devsel, latency 64, IRQ 11
I/O ports at df00 [size=64]
Capabilities: <available only to root>
0000:02:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
Subsystem: PC Partner Limited: Unknown device 8169 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 3 I/O ports at dc00 [size=256] Memory at fddfc000 (32-bit, non-prefetchable) [size=256] Expansion ROM at fdc00000 [disabled] [size=128K] Capabilities: <available only to root>
0000:02:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: PC Partner Limited: Unknown device 3044
Flags: bus master, stepping, medium devsel, latency 64, IRQ 11
Memory at fddfb000 (32-bit, non-prefetchable) [size=2K]
I/O ports at de00 [size=128]
Capabilities: <available only to root>
Quoted 28 lines · Carlo E. Prelz
Best regards to all and everyone. I just purchased a new RS480 (Radeon
XPress200)-based motherboard. It is a Sapphire Pure Performance PP-A9RS480. Mine is equipped with an Athlon64 3200+. I am attaching the output of lspci -vWhen booting with kernels from 2.6.15-rc1 up (tested with 2.6.15-rc1, 2.6.15-rc5, 2.6.15 and 2.6.16-rc1), the boot process freezes after displaying messages retated to registering io schedulers:
...
...
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registeredThere is no OOPS of any kind. The disk activity led remains on. With both 2.6.14 and 2.6.14.6, boot regularly continues with:
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe ([email protected]) and [email protected]
nbd: registered device at major 43
...
...
Quoted 8 lines
I tried to enable all debug options in configure, but no new message appears.
Important: I obtain the same result (frozen after "io scheduler cfq registered") when booting with a 100MB netinst debian sid bootdisk, downloaded last night. An older (9 month old) Ubuntu bootdisk boots perfectly. Both cd's are AMD64-specific.
Can you please add `initcall_debug' to the kernel boot command line? That'll tell us which function got stuck.
Subject: Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: sab 21 gen 06 01:09:32 -0800
Quoted 2 lines · Andrew Morton
Can you please add `initcall_debug' to the kernel boot command line? That'll tell us which function got stuck.
I photographed the screen. I am copying here the last few lines. I hope I make no errors in copying...
...
...
Installing knfsd (copyright (C) 1996 [email protected]). Calling initcall 0xffffffff806de042: init_nlm+0x0/0x21() Calling initcall 0xffffffff806de063: init_nls_cp437+0x0/0xc() Calling initcall 0xffffffff806de06f: init_nls_cp850+0x0/0xc() Calling initcall 0xffffffff806de07b: init_nls_cp852+0x0/0xc() Calling initcall 0xffffffff806de087: init_nls_iso8859_1+0x0/0xc() Calling initcall 0xffffffff806de093: init_nls_iso8859_15+0x0/0xc() Calling initcall 0xffffffff806de09f: init_nls_utf8+0x0/0x1f() Calling initcall 0xffffffff806de0be: init_autofs4_fs+0x0/0xc() Calling initcall 0xffffffff806de0ca: init_udf_fs+0x0/0x53() Calling initcall 0xffffffff806de11d: ipc_init+0x0/0x14() Calling initcall 0xffffffff806de2ea: init_mqueue_fs+0x0/0xc7() Calling initcall 0xffffffff806de51d: key_proc_init+0x0/0x52() Calling initcall 0xffffffff806de67c: init_crypto+0x0/0x18() Initializing Cryptographic API
Calling initcall 0xffffffff806de6b4: init+0x0/0xc() Calling initcall 0xffffffff806de6c0: init+0x0/0xc() Calling initcall 0xffffffff806de6cc: init+0x0/0xc() Calling initcall 0xffffffff806de6d8: init+0x0/0xc() Calling initcall 0xffffffff806de6e4: init+0x0/0x35() Calling initcall 0xffffffff806de719: init+0x0/0x5a() Calling initcall 0xffffffff806de773: init+0x0/0x5a() Calling initcall 0xffffffff806de7cd: init+0x0/0x35() Calling initcall 0xffffffff806de802: init+0x0/0xc() Calling initcall 0xffffffff806de80e: init+0x0/0xc() Calling initcall 0xffffffff806de81a: init+0x0/0x35() Calling initcall 0xffffffff806de84f: init+0x0/0xc() Calling initcall 0xffffffff806de85b: init+0x0/0xc() Calling initcall 0xffffffff806de867: arc4_init+0x0/0xc() Calling initcall 0xffffffff806de873: init+0x0/0x5a() Calling initcall 0xffffffff806de8cd: init+0x0/0xc() Calling initcall 0xffffffff806de8d9: init+0x0/0xc() Calling initcall 0xffffffff806de8e5: init+0x0/0xc() Calling initcall 0xffffffff806de8f1: michael_mic_init+0x0/0xc() Calling initcall 0xffffffff806de8fd: init+0x0/0xc() Calling initcall 0xffffffff806dea0a: noop_init+0x0/0xc() Scheduler noop registered
Calling initcall 0xffffffff806dea16: as_init+0x0/0x4f() Scheduler anticipatory registered
Calling initcall 0xffffffff806dea65: deadline_init+0x0/0x4f() Scheduler deadline registered
Calling initcall 0xffffffff806deab4: cfq_init+0x0/0xc4() Scheduler cfq registered
Calling initcall 0xffffffff8026836c: pci_init+0x0/0x2b()
And then the machine freezes. I may add that, with 2.6.14.6, I am getting errors like:
APIC error on CPU0: 04(40)
or, more often
APIC error on CPU0: 40(40)
I tried either to pass noapic, or to disable apic in bios, and the kernel entered a slow process of testing and refusing all addresses of my SCSI card (I tried both an Advansys and a NCR: the result has been the same) and then eventually gave an oops in ifconfig. I haven't photographed those messages, but I will do so if needed.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
Quoted 11 lines · Carlo E. Prelz
Subject: Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: sab 21 gen 06 01:09:32 -0800Quoted 2 lines · Andrew Morton
Can you please add `initcall_debug' to the kernel boot command line? That'll tell us which function got stuck.
I photographed the screen. I am copying here the last few lines. I hope I make no errors in copying...
Thanks. That's probably more lines than we needed ;)
If you have a web server somewhere, just upload the .jpg file. Or send it to me and I can do that.
Quoted 27 lines
...
...
Installing knfsd (copyright (C) 1996 [email protected]). Calling initcall0xffffffff806de042: init_nlm+0x0/0x21() Calling initcall0xffffffff806de063: init_nls_cp437+0x0/0xc() Calling initcall0xffffffff806de06f: init_nls_cp850+0x0/0xc() Calling initcall0xffffffff806de07b: init_nls_cp852+0x0/0xc() Calling initcall0xffffffff806de087: init_nls_iso8859_1+0x0/0xc() Calling initcall0xffffffff806de093: init_nls_iso8859_15+0x0/0xc() Calling initcall0xffffffff806de09f: init_nls_utf8+0x0/0x1f() Calling initcall0xffffffff806de0be: init_autofs4_fs+0x0/0xc() Calling initcall0xffffffff806de0ca: init_udf_fs+0x0/0x53() Calling initcall0xffffffff806de11d: ipc_init+0x0/0x14() Calling initcall0xffffffff806de2ea: init_mqueue_fs+0x0/0xc7() Calling initcall0xffffffff806de51d: key_proc_init+0x0/0x52() Calling initcall0xffffffff806de67c: init_crypto+0x0/0x18() Initializing Cryptographic API
Calling initcall0xffffffff806de6b4: init+0x0/0xc() Calling initcall0xffffffff806de6c0: init+0x0/0xc() Calling initcall0xffffffff806de6cc: init+0x0/0xc() Calling initcall0xffffffff806de6d8: init+0x0/0xc() Calling initcall0xffffffff806de6e4: init+0x0/0x35() Calling initcall0xffffffff806de719: init+0x0/0x5a() Calling initcall0xffffffff806de773: init+0x0/0x5a() Calling initcall0xffffffff806de7cd: init+0x0/0x35() Calling initcall0xffffffff806de802: init+0x0/0xc() Calling initcall0xffffffff806de80e: init+0x0/0xc()
Quoted 8 lines
Calling initcall
0xffffffff806de81a: init+0x0/0x35() Calling initcall0xffffffff806de84f: init+0x0/0xc() Calling initcall0xffffffff806de85b: init+0x0/0xc() Calling initcall0xffffffff806de867: arc4_init+0x0/0xc() Calling initcall0xffffffff806de873: init+0x0/0x5a() Calling initcall0xffffffff806de8cd: init+0x0/0xc() Calling initcall0xffffffff806de8d9: init+0x0/0xc() Calling initcall0xffffffff806de8e5: init+0x0/0xc()
Oh dear. We have 394 funtions all called 'init()' in the kernel. netfilter is a prime source.
Quoted 13 lines
Calling initcall
0xffffffff806de8f1: michael_mic_init+0x0/0xc() Calling initcall0xffffffff806de8fd: init+0x0/0xc() Calling initcall0xffffffff806dea0a: noop_init+0x0/0xc() Scheduler noop registered
Calling initcall0xffffffff806dea16: as_init+0x0/0x4f() Scheduler anticipatory registered
Calling initcall0xffffffff806dea65: deadline_init+0x0/0x4f() Scheduler deadline registered
Calling initcall0xffffffff806deab4: cfq_init+0x0/0xc4() Scheduler cfq registered
Calling initcall0xffffffff8026836c: pci_init+0x0/0x2b()
Quoted 2 lines
And then the machine freezes. I may add that, with 2.6.14.6, I am getting errors like:
OK, it looks like a PCI initcall went South. Can you please add this, then when it hangs, record the last few lines then send us those, as well as the output of `lspci -vx'?
drivers/pci/pci.c renamed from drivers/pci/pci.c~a +1 -0
@@ -886,6 +886,7 @@ static int __devinit pci_init(void)struct pci_dev *dev =NULL ;while ((dev =pci_get_device (PCI_ANY_ID ,PCI_ANY_ID , dev)) !=NULL ) { +printk ("pci_init: %04x%04x\n" , dev->vendor, dev->device);pci_fixup_device (pci_fixup_final, dev); }return 0 ;
_
Quoted 4 lines
APIC error on CPU0: 04(40)
or, more often
Quoted 8 lines
APIC error on CPU0: 40(40)
I tried either to pass noapic, or to disable apic in bios, and the kernel entered a slow process of testing and refusing all addresses of my SCSI card (I tried both an Advansys and a NCR: the result has been the same) and then eventually gave an oops in ifconfig. I haven't photographed those messages, but I will do so if needed.
Is this new behaviour? If so, are you able to pinpoint the latest kernel which didn't have such problems?
I had also had the problem that my Shuttle ST20G5 (a RS480 IGP based system) hung in pci_init. This was with one of the Fedora Rawhide kernels, after reporting it Dave Jones fixed it cause the next rawhide kernel worked again, maybe he could explain what it was, and where the fix is (if it is the same thing, but it really looks like it).
- Erwin
Quoted 5 lines · Erwin Rol
I had also had the problem that my Shuttle ST20G5 (a RS480 IGP based system) hung in
pci_init. This was with one of the Fedora Rawhide kernels, after reporting it Dave Jones fixed it cause the next rawhide kernel worked again, maybe he could explain what it was, and where the fix is (if it is the same thing, but it really looks like it).
That was due to us carrying one of the 'make the clock not tick at twice the speed on ati chipsets' patches. Matthew Garrett's variant iirc. It worked fine in .14, but caused havoc in .15+
I put it down to the problem being fixed in other ways upstream.
Dave
On Sat, Jan 21, 2006 at 05:04:02PM -0500, Dave Jones took 21 lines to write:
Quoted 7 lines · Erwin Rol
Quoted 5 lines
I had also had the problem that my Shuttle ST20G5 (a RS480 IGP based system) hung in
pci_init. This was with one of the Fedora Rawhide kernels, after reporting it Dave Jones fixed it cause the next rawhide kernel worked again, maybe he could explain what it was, and where the fix is (if it is the same thing, but it really looks like it).
Quoted 5 lines
That was due to us carrying one of the 'make the clock not tick at twice the speed on ati chipsets' patches. Matthew Garrett's variant iirc. It worked fine in .14, but caused havoc in .15+
I put it down to the problem being fixed in other ways upstream.
Heh. I think you mean s/fixed/worked around/.
The bugme tracking this, 3927, is a joyous muddle of patches, patches to patches, workarounds, and dueling command line options. I ported this patch,
http://www.ussg.iu.edu/hypermail/linux/kernel/0504.0/1625.html,
to 2.6.16-rc1 to fix my pain, but 1) it didn't work without the disable_timer_pin_1 kernel option and, 2) I don't think it's a fix so much as a workaround.
Kurt
Signature · 1 line
I can read your mind, and you should be ashamed of yourself.
Subject: Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: sab 21 gen 06 12:58:22 -0800
Quoted 2 lines · Andrew Morton
If you have a web server somewhere, just upload the .jpg file. Or send it to me and I can do that.
The latest screenshot can be found at
http://www.fluido.as/files/images/screenshot.jpg
Quoted 9 lines
Quoted 5 lines
Calling initcall
0xffffffff8026836c: pci_init+0x0/0x2b()And then the machine freezes. I may add that, with 2.6.14.6, I am getting errors like:
OK, it looks like a PCI initcall went South. Can you please add this, then when it hangs, record the last few lines then send us those, as well as the output of `lspci -vx'?
These lines appear at the end of the logfile:
pci_init: 10025950pci_init: 10025a3fpci_init: 1002437apci_init: 10024379pci_init: 10024374pci_init: 10024375pci_init: 10024373
and 1002:4373 is the USB2 (EHCI) controller. I attach the output of lspci -vx. Even with 2.6.14.6, I have problems with USB. It did not work at all, then I downloaded the latest bios, and now, right after boot, usb works OK. But after some time (possibly after the first APIC error message), newly inserted USB disks are not detected anymore, and I had one case in which a mounted disk was not accessible anymore.
I just bought the motherboard - I did not make too many tests.
Quoted 2 lines
Is this new behaviour? If so, are you able to pinpoint the latest kernel which didn't have such problems?
The motherboard is new. With the previous motherboard (via k8t88 based), using the same processor and most of the same boards, I did not have any of these problems.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
0000:00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01)
Subsystem: ATI Technologies Inc RS480 Host Bridge
Flags: bus master, 66MHz, medium devsel, latency 64
00: 02 10 50 59 06 00 20 22 01 00 00 06 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 50 59
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5a3f (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 99 Bus: primary=00, secondary=01, subordinate=01, sec-latency=68 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000d8000000-00000000dff00000 Capabilities: [44] #08 [a803] Capabilities: [b0] #0d [0000]
00: 02 10 3f 5a 07 00 30 02 00 00 04 06 00 63 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 44 e1 e1 20 02 20: e0 fd e0 fd 01 d8 f1 df 00 00 00 00 00 00 00 00 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 08 00
0000:00:11.0 IDE interface: ATI Technologies Inc ATI 437A Serial ATA Controller (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ATI Technologies Inc ATI 437A Serial ATA Controller Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10 I/O ports at ff00 [size=8] I/O ports at fe00 [size=4] I/O ports at fd00 [size=8] I/O ports at fc00 [size=4] I/O ports at fb00 [size=16] Memory at fe02f000 (32-bit, non-prefetchable) [size=512] Expansion ROM at 40000000 [disabled] [size=512K] Capabilities: [60] Power Management version 2 Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
00: 02 10 7a 43 07 00 b0 02 00 8f 01 01 08 40 00 00 10: 01 ff 00 00 01 fe 00 00 01 fd 00 00 01 fc 00 00 20: 01 fb 00 00 00 f0 02 fe 00 00 00 00 02 10 7a 43 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 00 00
0000:00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ATI Technologies Inc ATI 4379 Serial ATA Controller Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 5 I/O ports at fa00 [size=8] I/O ports at f900 [size=4] I/O ports at f800 [size=8] I/O ports at f700 [size=4] I/O ports at f600 [size=16] Memory at fe02e000 (32-bit, non-prefetchable) [size=512] Expansion ROM at 40080000 [disabled] [size=512K] Capabilities: [60] Power Management version 2 Capabilities: [50] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
00: 02 10 79 43 07 00 b0 02 00 8f 01 01 08 40 00 00 10: 01 fa 00 00 01 f9 00 00 01 f8 00 00 01 f7 00 00 20: 01 f6 00 00 00 e0 02 fe 00 00 00 00 02 10 79 43 30: 00 00 00 00 60 00 00 00 00 00 00 00 05 01 00 00
0000:00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI])
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
00: 02 10 74 43 07 00 b0 02 00 10 03 0c 10 40 80 00
10: 00 d0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 56 0a
30: 00 00 00 00 d0 00 00 00 00 00 00 00 0a 01 00 00
0000:00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI])
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
00: 02 10 75 43 07 00 b0 02 00 10 03 0c 10 40 00 00
10: 00 c0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 56 0a
30: 00 00 00 00 d0 00 00 00 00 00 00 00 0a 01 00 00
0000:00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (prog-if 20 [EHCI])
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Capabilities: [d0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
00: 02 10 73 43 17 00 b0 02 00 20 03 0c 10 40 00 00
10: 00 b0 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 56 0a
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 00 00
0000:00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 10)
Subsystem: PC Partner Limited: Unknown device 0a56 Flags: 66MHz, medium devsel I/O ports at 0400 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=1K] Capabilities: [b0] #08 [a802]
00: 02 10 72 43 03 04 30 02 10 00 05 0c 00 00 80 00 10: 01 04 00 00 00 a0 02 fe 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 56 0a 30: 00 00 00 00 b0 00 00 00 00 00 00 00 00 00 00 00
0000:00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI (prog-if 8a [Master SecP PriP])
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at f400 [size=16]
Capabilities: [70] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
00: 02 10 76 43 05 00 30 02 00 8a 01 01 00 40 00 00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
20: 01 f4 00 00 00 00 00 00 00 00 00 00 4b 17 56 0a
30: 00 00 00 00 70 00 00 00 00 00 00 00 ff 01 00 00
0000:00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge
Subsystem: PC Partner Limited: Unknown device 0a56
Flags: bus master, 66MHz, medium devsel, latency 0
00: 02 10 77 43 0f 00 20 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 56 0a
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (prog-if 01 [Subtractive decode])
Flags: bus master, VGA palette snoop, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=02, subordinate=03, sec-latency=64
I/O behind bridge: 0000c000-0000dfff
Memory behind bridge: fdc00000-fddfffff
Prefetchable memory behind bridge: fdb00000-fdbfffff
00: 02 10 71 43 27 00 a0 02 00 01 04 06 00 40 81 00
10: 00 00 00 00 00 00 00 00 00 02 03 40 c1 d1 80 22
20: c0 fd d0 fd b0 fd b0 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller (rev 01)
Subsystem: PC Partner Limited: Unknown device 5215
Flags: bus master, 66MHz, slow devsel, latency 64, IRQ 17
Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
00: 02 10 70 43 07 00 30 04 01 00 01 04 08 40 80 00
10: 00 90 02 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 15 52
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 02 02 00
0000:01:05.0 VGA compatible controller: ATI Technologies Inc RS480 [Radeon Xpress 200G Series] (prog-if 00 [VGA])
Subsystem: PC Partner Limited: Unknown device 0a56 Flags: bus master, 66MHz, medium devsel, latency 255, IRQ 11 Memory at d8000000 (32-bit, prefetchable) [size=128M] I/O ports at ee00 [size=256] Memory at fdef0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fde00000 [disabled] [size=128K] Capabilities: [50] Power Management version 2
00: 02 10 54 59 07 00 b0 02 00 00 00 03 08 ff 00 00 10: 08 00 00 d8 01 ee 00 00 00 00 ef fd 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 56 0a 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 08 00
0000:02:05.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Technotrend-Budget / Hauppauge WinTV-NOVA-S DVB card
Flags: bus master, medium devsel, latency 64, IRQ 16
Memory at fddff000 (32-bit, non-prefetchable) [size=512]
00: 31 11 46 71 06 00 80 02 01 00 80 04 00 40 00 00
10: 00 f0 df fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 c2 13 03 10
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 0f 26
0000:02:06.0 Multimedia controller: Philips Semiconductors SAA7133 Video Broadcast Decoder (rev d0)
Subsystem: Pinnacle Systems Inc.: Unknown device 002e
Flags: bus master, medium devsel, latency 64, IRQ 17
Memory at fddfe000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
00: 31 11 33 71 06 00 90 02 d0 00 80 04 00 40 00 00
10: 00 e0 df fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 bd 11 2e 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 54 20
0000:02:07.0 PCI bridge: PicoPower Technology PT86C525 [Nile-II] PCI-to-PCI Bridge (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, medium devsel, latency 64
Bus: primary=02, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: fdb00000-fdbfffff
00: 66 10 04 00 07 00 80 02 01 00 04 06 08 40 01 00
10: 00 00 00 00 00 00 00 00 02 03 03 20 c0 c0 80 02
20: c0 fd c0 fd b0 fd b0 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00
0000:02:08.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 06)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Flags: bus master, slow devsel, latency 64, IRQ 17
I/O ports at df00 [size=64]
Capabilities: [dc] Power Management version 1
00: 74 12 71 13 05 01 10 04 06 00 01 04 00 40 00 00
10: 01 df 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 74 12 71 13
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 0c 80
0000:02:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
Subsystem: PC Partner Limited: Unknown device 8169 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19 I/O ports at dc00 [size=256] Memory at fddfd000 (32-bit, non-prefetchable) [size=256] Expansion ROM at fdd00000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2
00: ec 10 69 81 17 00 b0 82 10 00 00 02 10 40 00 00 10: 01 dc 00 00 00 d0 df fd 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 69 81 30: 00 00 00 00 dc 00 00 00 00 00 00 00 03 01 20 40
0000:02:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: PC Partner Limited: Unknown device 3044
Flags: bus master, stepping, medium devsel, latency 64, IRQ 17
Memory at fddfc000 (32-bit, non-prefetchable) [size=2K]
I/O ports at de00 [size=128]
Capabilities: [50] Power Management version 2
00: 06 11 44 30 87 00 10 02 80 10 00 0c 08 40 00 00
10: 00 c0 df fd 01 de 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 44 30
30: 00 00 00 00 50 00 00 00 00 00 00 00 01 01 00 20
0000:03:08.0 SCSI storage controller: Advanced System Products, Inc ABP940-U / ABP960-U (rev 03)
Subsystem: Advanced System Products, Inc ASC1300 SCSI Adapter Flags: bus master, medium devsel, latency 64, IRQ 11 I/O ports at ce00 [size=256] Memory at fdcff000 (32-bit, non-prefetchable) [size=256] Expansion ROM at fdb00000 [disabled] [size=64K]
00: cd 10 00 13 07 00 80 02 03 00 00 01 08 40 00 00 10: 01 ce 00 00 00 f0 cf fd 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 3f 00 00 00 cd 10 10 13 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 04 04
0000:03:09.0 Multimedia video controller: Zoran Corporation ZR36057PQC Video cutting chipset (rev 02)
Subsystem: Iomega Corporation JPEG/TV Card
Flags: bus master, fast devsel, latency 32, IRQ 18
Memory at fdcfe000 (32-bit, non-prefetchable) [size=4K]
00: de 11 57 60 06 00 00 00 02 00 00 04 00 20 00 00
10: 00 e0 cf fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 ca 13 31 42
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 02 10
Quoted 32 lines · Carlo E. Prelz
Subject: Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: sab 21 gen 06 12:58:22 -0800Quoted 2 lines · Andrew Morton
If you have a web server somewhere, just upload the .jpg file. Or send it to me and I can do that.
The latest screenshot can be found at
http://www.fluido.as/files/images/screenshot.jpgQuoted 9 lines
Quoted 5 lines
Calling initcall
0xffffffff8026836c: pci_init+0x0/0x2b()And then the machine freezes. I may add that, with 2.6.14.6, I am getting errors like:
OK, it looks like a PCI initcall went South. Can you please add this, then when it hangs, record the last few lines then send us those, as well as the output of `lspci -vx'?
These lines appear at the end of the logfile:
pci_init: 10025950pci_init:10025a3fpci_init:1002437apci_init: 10024379pci_init: 10024374pci_init: 10024375pci_init: 10024373
Quoted 4 lines
and 1002:4373 is the USB2 (EHCI) controller. I attach the output of lspci -vx. Even with 2.6.14.6, I have problems with USB. It did not work at all, then I downloaded the latest bios, and now, right after boot, usb works OK.
OK, so it sounds like quirk_usb_disable_ehci() caused your machine to hang with the old BIOS. That's fairly bad behaviour from the kernel, even though the BIOS presumably had some problems.
Quoted 3 lines
But after some time (possibly after the first APIC
error message), newly inserted USB disks are not detected anymore, and I had one case in which a mounted disk was not accessible anymore.
Can you please gather some more details on this and prepare a new report? The full demsg output, machine description, etc. It might be best to do this via a new bugzilla.kernel.org record so we know where to find it.
Thanks.
Quoted 8 lines
I just bought the motherboard - I did not make too many tests.
Quoted 2 lines
Is this new behaviour? If so, are you able to pinpoint the latest kernel which didn't have such problems?
The motherboard is new. With the previous motherboard (via k8t88 based), using the same processor and most of the same boards, I did not have any of these problems.
Subject: Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: sab 21 gen 06 11:55:46 -0800
Quoted 8 lines · Andrew Morton
Quoted 4 lines
and 1002:4373 is the USB2 (EHCI) controller. I attach the output of lspci -vx. Even with 2.6.14.6, I have problems with USB. It did not work at all, then I downloaded the latest bios, and now, right after boot, usb works OK.
OK, so it sounds like
quirk_usb_disable_ehci()caused your machine to hang with the old BIOS. That's fairly bad behaviour from the kernel, even though the BIOS presumably had some problems.
It did not hang. When inserting USB disks, I got messages like:
ehci_hcd 0000:00:13.2: Unlink after no-IRQ? Controller is probably using the wrong IRQ. usb 1-1: device not accepting address 2, error -110
and the usb-storage module was not loaded. But the kernel went on working. After upgrading the BIOS, with the same kernel, the USB disk was recognized. But I now notice that the log file, with both old and new BIOS, contains these lines:
ehci_hcd 0000:00:13.2: BIOS handoff failed (160, 01010001) ehci_hcd 0000:00:13.2: continuing after BIOS bug...ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.2: irq 18, io mem 0xfe02b000ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
(only, the IRQ number changed from 10 to 18 after changing BIOS)
Quoted 4 lines
Can you please gather some more details on this and prepare a new report? The full demsg output, machine description, etc. It might be best to do this via a new bugzilla.kernel.org record so we know where to find it.
I will try that. I saw on apic.c that APIC error 40 should mean 'received illegal vector,' but I have no clue about how to interpret this.
I will now play a bit with BIOS USB parameters.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
Subject: Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: sab 21 gen 06 11:55:46 -0800
Quoted 3 lines · Andrew Morton
Can you please gather some more details on this and prepare a new report? The full demsg output, machine description, etc. It might be best to do this via a new bugzilla.kernel.org record so we know where to find it.
I filed bug #5935.
The BIOS contains 4 fields related to USB. In the 'Integrated peripherals' menu:
USB EHCI Controller
Onchip USB Controller
Onchip USB KBC Controller
In the 'PnP/PCI configurations' menu:
Assign IRQ for USB
All four only allow a choice between enable/disable. As expected, disabling the first one makes the 0000:00:13.2 pci device disappear. This results in the completing of the boot process. I am writing this from a working 2.6.15 kernel, and I can mount my USB hard disk. It probably works in 1.1 mode.
I noticed that the new motherboard's USB device is OHCI-based, while the previous one was UHCI-based. The OHCI driver was previously not compiled in. EHCI was functional even without a working OHCI module (in 2.6.14). Compiling in the OHCI driver has had no effect in the boot hang with EHCI enabled - the machine still hangs, and the output is identical.
Disabling the second field (Onchip USB Controller) makes all USB devices disappear - boot is OK, but there is no usb activity at all.
The third field has no evident effect. This is true of the fourth one too (the one about IRQ assignment). I saw no change in boot logs.
Complete dmesg output for the successful 2.6.15 boot with EHCI disabled can be downloaded from http://www.fluido.as/files/dmesg.txt.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
Time has passed without further mention of this problem. Today I took some time to discover exactly where the boot process was hanging. I found the place.
In drivers/usb/host/pci-quirks.c, in function quirk_usb_disable_ehci (should start around line 211) there is a stanza that reads:
/* always say Linux will own the hardware * by setting EHCI_USBLEGSUP_OS. */ pci_write_config_byte(pdev, offset + 3, 1);
On my sapphire athlon64 motherboard (see the thread for more details), this call never returns (without generating any output). I commented it out, and now the EHCI subsystem works OK (currently running 2.6.16rc2).
I do not know what the right patch should be.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
Quoted 8 lines · Carlo E. Prelz
In
drivers/usb/host/pci-quirks.c, in functionquirk_usb_disable_ehci(should start around line 211) there is a stanza that reads:/* always say Linux will own the hardware * by setting EHCI_USBLEGSUP_OS. */ pci_write_config_byte(pdev, offset + 3, 1);
Quoted 4 lines
On my sapphire athlon64 motherboard (see the thread for more details), this call never returns (without generating any output). I commented it out, and now the EHCI subsystem works OK (currently running 2.6.16rc2).
Interesting ... feels like a BIOS problem. If you want to experiment, there's a right bracket -- "}" -- immediately before that. Try moving it right after that write, so that write_config_byte is covered by the preceding "if LEGSUP_BIOS" test; or copying the much later "disable SMI" clause into an "else" for that "if".
- Dave
Subject: Re: [linux-usb-devel] Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: dom 05 feb 06 11:45:22 -0800
Quoted 5 lines · David Brownell
Interesting ... feels like a BIOS problem. If you want to experiment, there's a right bracket -- "}" -- immediately before that. Try moving it right after that write, so that
write_config_byteis covered by the preceding "ifLEGSUP_BIOS" test; or copying the much later "disable SMI" clause into an "else" for that "if".
The first one would be useless - I inserted lots of printouts to find out where the freeze took place, and I know that the EHCI_USBLEGSUP_BIOS flag is on (cap is 0x10001). The value remains the same after the 'spin till it hands it over' loop - so that this printout appears:
0000:00:13.2 EHCI: BIOS handoff failed (BIOS bug ?)
About the second thing you suggest: do you refer to this call?
/* just in case, always disable EHCI SMIs */ pci_write_config_dword(pdev, offset + EHCI_USBLEGCTLSTS, 0);
In my machine, the write takes place without apparent ill effects. If I add it as an else clause to the "if LEGSUP_BIOS" test, it won't execute, because the EHCI_USBLEGSUP_BIOS flag is on.
In case you need it: hcc_params is 0xa012.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
Quoted 7 lines · Carlo E. Prelz
Quoted 6 lines
Interesting ... feels like a BIOS problem. If you want to experiment, there's a right bracket -- "}" -- immediately before that. Try moving it right after that write, so that
write_config_byteis covered by the preceding "ifLEGSUP_BIOS" test; or copying the much later "disable SMI" clause into an "else" for that "if".
Quoted 7 lines
The first one would be useless - I inserted lots of printouts to find out where the freeze took place, and I know that the
EHCI_USBLEGSUP_BIOSflag is on (cap is0x10001). The value remains the same after the 'spin till it hands it over' loop - so that this printout appears:0000:00:13.2 EHCI: BIOS handoff failed (BIOS bug ?)
If it printed that, then how is it possible that it hung _before_ printing that message??? Your reports are not making any sense to me.
Maybe that whole "if" block that turns that SMI _on_ is the problem; it was part of the "early handoff" code, which came from who knows where, was clearly buggy, and was never widely used until recently. Enabling the SMI seemed pretty dubious to me, but I suspect that some undescribed buggy BIOS really does need it ... maybe whoever provided that "early" handoff version could report what they were trying to do by enabling the SMI?
- Dave
Subject: Re: [linux-usb-devel] Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: Mon 06 Feb 06 08:24:04AM -0800
Quoted 2 lines · David Brownell
If it printed that, then how is it possible that it hung _before_ printing that message???
I already wrote that I had commented out the line that caused the hangup:
// pci_write_config_byte(pdev, offset + 3, 1);
After commenting out this line, the machine boots OK and EHCI works fine. It does print the BIOS handoff failed message.
If I do not comment out the above line, the machine hangs, and, obviously, no BIOS handoff failed message is printed.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
Quoted 11 lines
Quoted 3 lines
If it printed that, then how is it possible that it hung _before_ printing that message???
I already wrote that I had commented out the line that caused the hangup:
//
pci_write_config_byte(pdev, offset + 3, 1);After commenting out this line, the machine boots OK and EHCI works fine. It does print the BIOS handoff failed message.
Then if disabling that code which enables the SMI doesn't work, you have only one real option other than telling your BIOS not to support USB keyboards/mice/disks: replace your BIOS.
The reason it prints the BIOS handoff message is because you completely disabled the handoff, so your BIOS still thinks it owns that controller. Commenting out that line is not good.
Subject: Re: [linux-usb-devel] Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: Mon 06 Feb 06 09:31:14AM -0800
Quoted 3 lines · David Brownell
Then if disabling that code which enables the SMI doesn't work, you have only one real option other than telling your BIOS not to support USB keyboards/mice/disks: replace your BIOS.
Sapphire has no newer bios than the one I am using. But I am saying that USB works with that line commented out. I tried a couple of USB disks, a USB mouse and my palm pilot - all seem to work quite OK. No angry messages.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
Quoted 4 lines
OK, so it sounds like
quirk_usb_disable_ehci()caused your machine to hang with the old BIOS. That's fairly bad behaviour from the kernel, even though the BIOS presumably had some problems.
I think what happened is the "always run quirks" code got turned into the default too early, before the EHCI "quirk" version of the handoff code got checked against what most systems have been using for the past several years.
I noticed at least one suspicous thing: it enables an SMI IRQ. Even in cases when the boot firmware says it's not using EHCI ... easy to imagine that causing hangage.
Maybe this time it'd help to tell your BIOS "yes, DO use USB". Or, the attached patch might help. Please try both experiments.
- Dave
This moves the previously widely-used ehci-pci.c BIOS handoff code into the pci-quirks.c file, replacing the less widely used "early handoff" version that seems to cause problems lately.
One notable change: the "early handoff" version always enabled an SMI IRQ ... and did so even if the pre-Linux code said it was not using EHCI (and not expecting EHCI SMIs). Looks like a goof in a workaround for some unknown BIOS version.
This merged version only forcibly enables those IRQs when pre-Linux code says it's using EHCI. And now it always forces them off "just in case".
EXPERIMENTAL
drivers/usb/host/ehci-pci.c +3 -60
@@ -24,40 +24,6 @@/*-------------------------------------------------------------------------*/ -/* EHCI 0.96 (and later) section 5.1 says how to kick BIOS/SMM/... -* off the controller (maybe it can boot from highspeed USB disks). -*/ -static int bios_handoff (struct ehci_hcd *ehci,int where,u32 cap) -{ -struct pci_dev *pdev =to_pci_dev (ehci_to_hcd (ehci)->self.controller); - -/* always say Linux will own the hardware */ -pci_write_config_byte (pdev, where +3 ,1 ); - -/* maybe wait a while for BIOS to respond */ -if (cap & (1 <<16 )) { -int msec =5000 ; - -do { -msleep (10 ); - msec -=10 ; -pci_read_config_dword (pdev, where, &cap); - }while ((cap & (1 <<16 )) && msec); -if (cap & (1 <<16 )) { -ehci_err (ehci,"BIOS handoff failed (%d, %08x)\n" , - where, cap); -// some BIOS versions seem buggy... -// return 1; -ehci_warn (ehci,"continuing after BIOS bug...\n" ); -/* disable all SMIs, and clear "BIOS owns" flag */ -pci_write_config_dword (pdev, where +4 ,0 ); -pci_write_config_byte (pdev, where +2 ,0 ); - }else -ehci_dbg (ehci,"BIOS handoff succeeded\n" ); - } -return 0 ; -} -/* called after powerup, by probe or system-pm "wakeup" */ static int ehci_pci_reinit (struct ehci_hcd *ehci,struct pci_dev *pdev) {
@@ -84,32 +50,9 @@ static int ehci_pci_reinit(struct ehci_h } } - temp =HCC_EXT_CAPS (readl (&ehci->caps->hcc_params)); - -/* EHCI 0.96 and later may have "extended capabilities" */ -while (temp && count--) { -u32 cap; - -pci_read_config_dword (pdev, temp, &cap); -ehci_dbg (ehci,"capability %04x at %02x\n" , cap, temp); -switch (cap &0xff ) { -case 1 :/* BIOS/SMM/... handoff */ -if (bios_handoff (ehci, temp, cap) !=0 ) -return -EOPNOTSUPP ; -break ; -case 0 :/* illegal reserved capability */ -ehci_dbg (ehci,"illegal capability!\n" ); - cap =0 ; -/* FALLTHROUGH */ -default :/* unknown */ -break ; - } - temp = (cap >>8 ) &0xff ; - } -if (!count) { -ehci_err (ehci,"bogus capabilities ... PCI problems!\n" ); -return -EIO ; - } +/* we expect static quirk code to handle the "extended capabilities" +* (currently just BIOS handoff) allowed starting with EHCI 0.96 +*/ /* PCI Memory-Write-Invalidate cycle support is optional (uncommon) */ retval =pci_set_mwi (pdev);
drivers/usb/host/pci-quirks.c +68 -38
134 lines not on this page · raw message
Subject: Re: [linux-usb-devel] Re: ATI RS480-based motherboard: stuck while booting with kernel >= 2.6.15 rc1 Date: lun 23 gen 06 11:01:25 -0800
Quoted 1 line · David Brownell
Maybe this time it'd help to tell your BIOS "yes, DO use USB".
That I am doing. And I now have the appropriate OHCI module loaded. USB 1.1 works apparently quite OK.
Quoted 1 line
Or, the attached patch might help.
I applied the patch. The three changes to the second file applied with an offset of 6 lines (to 2.6.15 vanilla). Nothing changed: the booting process hung at the same place, generating the same printout as before. I have now booted the new kernel with EHCI disabled, and saved the dmesg oputput to http://www.fluido.as/files/dmesg2.txt (here, USB1.1 is active).
It is time for sleep for me. I will perform any new test tomorrow morning.
Carlo
Signature · 3 lines
* Se la Strada e la sua Virtu' non fossero state messe da parte, * K * Carlo E. Prelz - [email protected] che bisogno ci sarebbe * di parlare tanto di amore e di rettitudine? (Chuang-Tzu)
Quoted 4 lines · David Brownell
This moves the previously widely-used
ehci-pci.cBIOS handoff code into thepci-quirks.cfile, replacing the less widely used "early handoff" version that seems to cause problems lately.
Quoted 8 lines
One notable change: the "early handoff" version always enabled an SMI IRQ ... and did so even if the pre-Linux code said it was not using EHCI (and not expecting EHCI SMIs). Looks like a goof in a workaround for some unknown BIOS version.
This merged version only forcibly enables those IRQs when pre-Linux code says it's using EHCI. And now it always forces them off "just in case".
Thanks for posting this, it fixes my EHCI + APIC error, and makes my laptop work just fine.
Turns out that 2.6.14 worked for it, but 2.6.15 didn't. git bisect a zillion times later narrowed it down to the usb early handoff stuff but due to merge issues, it was tough to track down the exact patch.
For fun I tried this one on top of the latest -mm, and it works!
So, care to clean it up to make it feel better to you and send it to me again so I can add it to my tree? I know the next SuSE kernel will need it :)
thanks,
greg k-h
Quoted 10 lines · Greg KH
Quoted 9 lines · David Brownell
This moves the previously widely-used
ehci-pci.cBIOS handoff code into thepci-quirks.cfile, replacing the less widely used "early handoff" version that seems to cause problems lately.One notable change: the "early handoff" version always enabled an SMI IRQ ... and did so even if the pre-Linux code said it was not using EHCI (and not expecting EHCI SMIs). Looks like a goof in a workaround for some unknown BIOS version.
Quoted 6 lines
Quoted 3 lines
This merged version only forcibly enables those IRQs when pre-Linux code says it's using EHCI. And now it always forces them off "just in case".
Thanks for posting this, it fixes my EHCI + APIC error, and makes my laptop work just fine.
OK, here's a version with a Signed-Off-By; against current GIT.
I'm mildly surprised it helps that laptop, but not surprised that it helps _some_ of those "ehci init goofs" cases. :)
- Dave
This moves the previously widely-used ehci-pci.c BIOS handoff code into the pci-quirks.c file, replacing the less widely used "early handoff" version that seems to cause problems lately.
One notable change: the "early handoff" version always enabled an SMI IRQ ... and did so even if the pre-Linux code said it was not using EHCI (and not expecting EHCI SMIs). Looks like a goof in a workaround for some unknown BIOS version.
This merged version only forcibly enables those IRQs when pre-Linux code says it's using EHCI. And now it always forces them off "just in case".
drivers/usb/host/ehci-pci.c +3 -60
@@ -24,40 +24,6 @@/*-------------------------------------------------------------------------*/ -/* EHCI 0.96 (and later) section 5.1 says how to kick BIOS/SMM/... -* off the controller (maybe it can boot from highspeed USB disks). -*/ -static int bios_handoff (struct ehci_hcd *ehci,int where,u32 cap) -{ -struct pci_dev *pdev =to_pci_dev (ehci_to_hcd (ehci)->self.controller); - -/* always say Linux will own the hardware */ -pci_write_config_byte (pdev, where +3 ,1 ); - -/* maybe wait a while for BIOS to respond */ -if (cap & (1 <<16 )) { -int msec =5000 ; - -do { -msleep (10 ); - msec -=10 ; -pci_read_config_dword (pdev, where, &cap); - }while ((cap & (1 <<16 )) && msec); -if (cap & (1 <<16 )) { -ehci_err (ehci,"BIOS handoff failed (%d, %08x)\n" , - where, cap); -// some BIOS versions seem buggy... -// return 1; -ehci_warn (ehci,"continuing after BIOS bug...\n" ); -/* disable all SMIs, and clear "BIOS owns" flag */ -pci_write_config_dword (pdev, where +4 ,0 ); -pci_write_config_byte (pdev, where +2 ,0 ); - }else -ehci_dbg (ehci,"BIOS handoff succeeded\n" ); - } -return 0 ; -} -/* called after powerup, by probe or system-pm "wakeup" */ static int ehci_pci_reinit (struct ehci_hcd *ehci,struct pci_dev *pdev) {
@@ -84,32 +50,9 @@ static int ehci_pci_reinit(struct ehci_h } } - temp =HCC_EXT_CAPS (readl (&ehci->caps->hcc_params)); - -/* EHCI 0.96 and later may have "extended capabilities" */ -while (temp && count--) { -u32 cap; - -pci_read_config_dword (pdev, temp, &cap); -ehci_dbg (ehci,"capability %04x at %02x\n" , cap, temp); -switch (cap &0xff ) { -case 1 :/* BIOS/SMM/... handoff */ -if (bios_handoff (ehci, temp, cap) !=0 ) -return -EOPNOTSUPP ; -break ; -case 0 :/* illegal reserved capability */ -ehci_dbg (ehci,"illegal capability!\n" ); - cap =0 ; -/* FALLTHROUGH */ -default :/* unknown */ -break ; - } - temp = (cap >>8 ) &0xff ; - } -if (!count) { -ehci_err (ehci,"bogus capabilities ... PCI problems!\n" ); -return -EIO ; - } +/* we expect static quirk code to handle the "extended capabilities" +* (currently just BIOS handoff) allowed starting with EHCI 0.96 +*/ /* PCI Memory-Write-Invalidate cycle support is optional (uncommon) */ retval =pci_set_mwi (pdev);
drivers/usb/host/pci-quirks.c +68 -38
134 lines not on this page · raw message