(SOLVED!) AHA-7850 doesn't detect scanner anymore
One pin on the connector didn't have proper contact. Thx,
Gerrit
---------- Weitergeleitete Nachricht ----------
Subject: AHA-7850 doesn't detect scanner anymore
Date: Samstag, 21. Januar 2006 13:46
From: Gerrit Bruchhäuser <[email protected]>
To: [email protected]
Hello,
my old "HP ScanJet IIc" used to work so perfectly but now the kernel can only see something at SCSI-ID 1, but is not able to detect the device properly :-(
These are the 'kernel.log' entries after I switched on 'options aic7xxx
aic7xxx=verbose,periodic_otag' in modules.conf file :
| Jan 21 13:17:18 gbpc PCI: Enabling device 0000:00:0d.0 (0116 -> 0117) | Jan 21 13:17:18 gbpc ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 17 (level,
low) -> IRQ 185
| Jan 21 13:17:18 gbpc ahc_pci:0:13:0: hardware scb 64 bytes; kernel scb 52
bytes; ahc_dma 8 bytes
| Jan 21 13:17:18 gbpc ahc_pci:0:13:0: Host Adapter Bios disabled. Using
default SCSI device parameters
| Jan 21 13:17:18 gbpc scsi12 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER,
Rev 7.0
| Jan 21 13:17:18 gbpc <Adaptec 2902/04/10/15/20C/30C SCSI adapter> | Jan 21 13:17:18 gbpc aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs | Jan 21 13:17:18 gbpc | Jan 21 13:17:33 gbpc (scsi12:A:0:0): Saw Selection Timeout for SCB 0x3 | Jan 21 13:17:34 gbpc (scsi12:A:1:0): SCB 2: requests Check Status | Jan 21 13:17:34 gbpc (scsi12:A:1:0): Handled Residual of 36 bytes | Jan 21 13:17:34 gbpc (scsi12:A:1:0): Sending Sense | Jan 21 13:17:34 gbpc (scsi12:A:1:0): Handled Residual of 36 bytes | Jan 21 13:17:34 gbpc (scsi12:A:1:0): SCB 3: requests Check Status | Jan 21 13:17:34 gbpc (scsi12:A:1:0): Handled Residual of 36 bytes | Jan 21 13:17:34 gbpc (scsi12:A:1:0): Sending Sense | Jan 21 13:17:34 gbpc (scsi12:A:1:0): Handled Residual of 36 bytes | Jan 21 13:17:35 gbpc (scsi12:A:1:0): SCB 2: requests Check Status | Jan 21 13:17:35 gbpc (scsi12:A:1:0): Handled Residual of 36 bytes | Jan 21 13:17:35 gbpc (scsi12:A:1:0): Sending Sense | Jan 21 13:17:35 gbpc (scsi12:A:1:0): Handled Residual of 36 bytes | Jan 21 13:17:35 gbpc (scsi12:A:2:0): Saw Selection Timeout for SCB 0x3 | Jan 21 13:17:35 gbpc (scsi12:A:3:0): Saw Selection Timeout for SCB 0x2 | Jan 21 13:17:36 gbpc (scsi12:A:4:0): Saw Selection Timeout for SCB 0x3 | Jan 21 13:17:36 gbpc (scsi12:A:5:0): Saw Selection Timeout for SCB 0x2 | Jan 21 13:17:36 gbpc (scsi12:A:6:0): Saw Selection Timeout for SCB 0x3
The SCSI-terminator is properly attached to the scanner and the wires are
okay as well. Is there a way to find-out more what actually causes the problem?
As I am not subscribed to the list, please when you answer, put my mail address to CC
Many thanks in advance,
Gerrit
-------------------------------------------------------