Skip to contentSkip to conversation

w83781d: Don't reset the chip by default

PATCH New Jean Delvare 1 participant 1 message Feb 5, 2006

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 7/11 w83781d: Don't reset the chip by default

Content-Disposition: inline; filename=hwmon-w83781d-no-reset-by-default.patch

Stop resetting the chip on load by default, so as to preserve the BIOS initializations. Same was done in the w83627hf driver some times ago for the same reasons.

Signed-off-by Jean Delvare <khali at linux-fr.org>
---
 Documentation/hwmon/w83781d |    5 +++++
 drivers/hwmon/w83781d.c     |   22 +++++++++++++++++++++-
 2 files changed, 26 insertions(+), 1 deletion(-)
drivers/hwmon/w83781d.c +21 -1
@@ -57,6 +57,10 @@
 I2C_CLIENT_MODULE_PARM(force_subclients, "List of subclient addresses: "
 		    "{bus, clientaddr, subclientaddr1, subclientaddr2}");
 
+static int reset;
+module_param(reset, bool, 0);
+MODULE_PARM_DESC(reset, "Set to one to reset chip on load");
+
 static int init = 1;
 module_param(init, bool, 0);
 MODULE_PARM_DESC(init, "Set to zero to bypass chip initialization");
@@ -1460,8 +1464,17 @@
 	int type = data->type;
 	u8 tmp;
 
-	if (init && type != as99127f) {	/* this resets registers we don't have
+	if (reset && type != as99127f) { /* this resets registers we don't have
 					   documentation for on the as99127f */
+		/* Resetting the chip has been the default for a long time,
+		   but it causes the BIOS initializations (fan clock dividers,
+		   thermal sensor types...) to be lost, so it is now optional.
+		   It might even go away if nobody reports it as being useful,
+		   as I see very little reason why this would be needed at
+		   all. */
+		dev_info(&client->dev, "If reset=1 solved a problem you were "
+			 "having, please report!\n");
+
 		/* save these registers */
 		i = w83781d_read_value(client, W83781D_REG_BEEP_CONFIG);
 		p = w83781d_read_value(client, W83781D_REG_PWMCLK12);
@@ -1478,6 +1491,13 @@
 		w83781d_write_value(client, W83781D_REG_BEEP_INTS2, 0);
 	}
 
+	/* Disable power-on abnormal beep, as advised by the datasheet.
+	   Already done if reset=1. */
+	if (init && !reset && type != as99127f) {
+		i = w83781d_read_value(client, W83781D_REG_BEEP_CONFIG);
+		w83781d_write_value(client, W83781D_REG_BEEP_CONFIG, i | 0x80);
+	}
+
 	data->vrm = vid_which_vrm();
 
 	if ((type != w83781d) && (type != as99127f)) {
Documentation/hwmon/w83781d +5 -0
@@ -36,6 +36,11 @@
   Use 'init=0' to bypass initializing the chip.
   Try this if your computer crashes when you load the module.
 
+* reset int
+  (default 0)
+  The driver used to reset the chip on load, but does no more. Use
+  'reset=1' to restore the old behavior. Report if you need to do this.
+
 force_subclients=bus,caddr,saddr,saddr
   This is used to force the i2c addresses for subclients of
   a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b'
Signature · 1 line
Jean Delvare