Skip to contentSkip to conversation

nfsroot.txt (against Linux 2.6.15.2)

PATCH RESEND In review Nico Schottelius 3 participants 5 messages Feb 10, 2006 – Feb 11, 2006 Documentation

lore
Share & tools
lore
#0 lore raw

PATCH RESEND 1/1 nfsroot.txt (against Linux 2.6.15.2)

[This message was sent to the LKML on Mon, 6 Feb 2006 16:29:46 +0100
and nobody replied. Perhaps you did not see it in the flood of mails.]

Hello dear developers,

I today booted the first time my embedded device using Linux 2.6.15.2, which was booted by pxelinux, which then bootet itself from the nfsroot.

This went pretty fine, but when I was reading through Documentation/nfsroot.txt I saw that there are some more modern versions available of loading the kernel and passing parameters.

So I added them and the patch for that is attached to this mail.

Sincerly,

Nico

P.S.: Please reply to nico-kernel2 //at// schottelius.org

Signature · 2 lines
Latest release: ccollect-0.3.2 (http://linux.schottelius.org/ccollect/)
Open Source nutures open minds and free, creative developers.
nfsroot.txt renamed from nfsroot.txt.orig +14 -3
@@ -3,6 +3,7 @@
 
 Written 1996 by Gero Kuhlmann <[email protected]>
 Updated 1997 by Martin Mares <[email protected]>
+Updated 2006 by Nico Schottelius <[email protected]>
 
 
 
@@ -168,7 +169,6 @@
 	root. If it got a BOOTP answer the directory name in that answer
 	is used.
 
-
 3.2) Using LILO
 	When using LILO you can specify all necessary command line
 	parameters with the 'append=' command in the LILO configuration
@@ -177,7 +177,11 @@
 	LILO and its 'append=' command please refer to the LILO
 	documentation.
 
-3.3) Using loadlin
+3.3) Using GRUB
+	When you use GRUB, you simply append the parameters after the kernel
+	specification: "kernel <kernel> <parameters>" (without the quotes).
+
+3.4) Using loadlin
 	When you want to boot Linux from a DOS command prompt without
 	having a local hard disk to mount as root, you can use loadlin.
 	I was told that it works, but haven't used it myself yet. In
@@ -185,7 +189,7 @@
 	lar to how LILO is doing it. Please refer to the loadlin docu-
 	mentation for further information.
 
-3.4) Using a boot ROM
+3.5) Using a boot ROM
 	This is probably the most elegant way of booting a diskless
 	client. With a boot ROM the kernel gets loaded using the TFTP
 	protocol. As far as I know, no commercial boot ROMs yet
@@ -194,6 +198,13 @@
 	and its mirrors. They are called 'netboot-nfs' and 'etherboot'.
 	Both contain everything you need to boot a diskless Linux client.
 
+3.6) Using pxelinux
+	Using pxelinux you specify the kernel you built with
+	"kernel <relative-path-below /tftpboot>". The nfsroot parameters
+	are passed to the kernel by adding them to the "append" line.
+	You may perhaps also want to fine tune the console output,
+	see Documentation/serial-console.txt for serial console help.
+
 
 
 
#1 lore raw
Quoted 11 lines · Nico Schottelius

[This message was sent to the LKML on Mon, 6 Feb 2006 16:29:46 +0100
and nobody replied. Perhaps you did not see it in the flood of mails.]

Hello dear developers,

I today booted the first time my embedded device using Linux 2.6.15.2, which was booted by pxelinux, which then bootet itself from the nfsroot.

This went pretty fine, but when I was reading through Documentation/nfsroot.txt I saw that there are some more modern versions available of loading the kernel and passing parameters.

Looks good.

Quoted 1 line

So I added them and the patch for that is attached to this mail.

Inline patches preferred.

Quoted 5 lines

Sincerly,

Nico

P.S.: Please reply to nico-kernel2 //at// schottelius.org

Easier if this is your From: address, initially ;-)

nfsroot.txt

Quoted 3 lines
nfsroot.txt renamed from nfsroot.txt.orig +0 -0
@@ -3,6 +3,7 @@

Patches must be in a format that applies with `diff -p1'. diffstat(1) output doesn't hurt, either. See Documentation/SubmittingPatches and
http://www.zip.com.au/~akpm/linux/patches/stuff/tpp.txt for details.

[ snip ]

#2 lore raw
Quoted 1 line · Arthur Othieno

Patches must be in a format that applies with `diff -p1'. diffstat(1)

                                                 ^^^^

That was patch, of course.
Frederik

#3 lore raw
Quoted 5 lines · Frederik Deweerdt
Quoted 1 line · Arthur Othieno

Patches must be in a format that applies with `diff -p1'. diffstat(1)

                                                 ^^^^

That was patch, of course.

Right. Silly me.

#4 lore raw

PATCH 1/1 Updated Documentation/nfsroot.txt

In reply to Arthur Othieno

[I followed the instructions in
http://www.zip.com.au/~akpm/linux/patches/stuff/tpp.txt and Documentation/SubmittingPatches and corrected my patch submission. I hope it's ok this time. I copied the original text so you can use it for the changelog.]

Hello dear developers,

I today booted the first time my embedded device using Linux 2.6.15.2, which was booted by pxelinux, which then bootet itself from the nfsroot.

This went pretty fine, but when I was reading through Documentation/nfsroot.txt I saw that there are some more modern versions available of loading the kernel and passing parameters.

So I added them and the patch for that is attached to this mail.

Sincerly,

Nico

Documentation/nfsroot.txt renamed from Documentation/nfsroot.txt.orig +14 -4
@@ -3,6 +3,7 @@
 
 Written 1996 by Gero Kuhlmann <[email protected]>
 Updated 1997 by Martin Mares <[email protected]>
+Updated 2006 by Nico Schottelius <[email protected]>
 
 
 
@@ -168,7 +169,6 @@
 	root. If it got a BOOTP answer the directory name in that answer
 	is used.
 
-
 3.2) Using LILO
 	When using LILO you can specify all necessary command line
 	parameters with the 'append=' command in the LILO configuration
@@ -177,7 +177,11 @@
 	LILO and its 'append=' command please refer to the LILO
 	documentation.
 
-3.3) Using loadlin
+3.3) Using GRUB
+	When you use GRUB, you simply append the parameters after the kernel
+	specification: "kernel <kernel> <parameters>" (without the quotes).
+
+3.4) Using loadlin
 	When you want to boot Linux from a DOS command prompt without
 	having a local hard disk to mount as root, you can use loadlin.
 	I was told that it works, but haven't used it myself yet. In
@@ -185,7 +189,7 @@
 	lar to how LILO is doing it. Please refer to the loadlin docu-
 	mentation for further information.
 
-3.4) Using a boot ROM
+3.5) Using a boot ROM
 	This is probably the most elegant way of booting a diskless
 	client. With a boot ROM the kernel gets loaded using the TFTP
 	protocol. As far as I know, no commercial boot ROMs yet
@@ -194,6 +198,13 @@
 	and its mirrors. They are called 'netboot-nfs' and 'etherboot'.
 	Both contain everything you need to boot a diskless Linux client.
 
+3.6) Using pxelinux
+	Using pxelinux you specify the kernel you built with
+	"kernel <relative-path-below /tftpboot>". The nfsroot parameters
+	are passed to the kernel by adding them to the "append" line.
+	You may perhaps also want to fine tune the console output,
+	see Documentation/serial-console.txt for serial console help.
+
 
 
-- 

Latest release: ccollect-0.3.2 (http://linux.schottelius.org/ccollect/)
Open Source nutures open minds and free, creative developers.