Skip to contentSkip to conversation

ata_piix: convert pata to new reset mechanism

PATCH NAK Tejun Heo 2 participants 4 messages Feb 12, 2006

Subsystems (2)
lore
Share & tools
lore

Tejun Heo

author
#0 lore raw

PATCH 1/1 ata_piix: convert pata to new reset mechanism

[PATCH] ata_piix: convert pata to new reset mechanism

Convert ata_piix pata ->phy_reset to new reset mechanism.

--

Jeff, this patch assumes that all-probe_reset-to-return-UNKNOWN[1] is applied.

[1] http://article.gmane.org/gmane.linux.ide/7967

 ata_piix.c |   44 ++++++++++++++++++++++++++++----------------
 1 file changed, 28 insertions(+), 16 deletions(-)
drivers/scsi/ata_piix.c +28 -16
Index: work1/drivers/scsi/ata_piix.c
===================================================================
@@ -131,7 +131,7 @@ enum {
 static int piix_init_one (struct pci_dev *pdev,
 				    const struct pci_device_id *ent);
 
-static void piix_pata_phy_reset(struct ata_port *ap);
+static int piix_pata_probe_reset(struct ata_port *ap, unsigned int *classes);
 static void piix_sata_phy_reset(struct ata_port *ap);
 static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
 static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
@@ -208,7 +208,7 @@ static const struct ata_port_operations 
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
 
-	.phy_reset		= piix_pata_phy_reset,
+	.probe_reset		= piix_pata_probe_reset,
 
 	.bmdma_setup		= ata_bmdma_setup,
 	.bmdma_start		= ata_bmdma_start,
@@ -259,8 +259,7 @@ static struct ata_port_info piix_port_in
 	/* ich5_pata */
 	{
 		.sht		= &piix_sht,
-		.host_flags	= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST |
-				  PIIX_FLAG_CHECKINTR,
+		.host_flags	= ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
 		.pio_mask	= 0x1f,	/* pio0-4 */
 #if 0
 		.mwdma_mask	= 0x06, /* mwdma1-2 */
@@ -285,7 +284,7 @@ static struct ata_port_info piix_port_in
 	/* piix4_pata */
 	{
 		.sht		= &piix_sht,
-		.host_flags	= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+		.host_flags	= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= 0x1f,	/* pio0-4 */
 #if 0
 		.mwdma_mask	= 0x06, /* mwdma1-2 */
@@ -367,30 +366,43 @@ cbl40:
 }
 
 /**
- *	piix_pata_phy_reset - Probe specified port on PATA host controller
- *	@ap: Port to probe
+ *	piix_pata_postreset - Postreset stuff on PATA host controller
+ *	@ap: Target port
+ *	@classes: Classes of attached devices
  *
- *	Probe PATA phy.
+ *	Postreset processing including cable detection.
  *
  *	LOCKING:
  *	None (inherited from caller).
  */
+static void piix_pata_postreset(struct ata_port *ap, unsigned int *classes)
+{
+	piix_pata_cbl_detect(ap);
+	ata_std_postreset(ap, classes);
+}
 
-static void piix_pata_phy_reset(struct ata_port *ap)
+/**
+ *	piix_pata_probe_reset - Perform reset on PATA port and classify
+ *	@ap: Port to reset
+ *	@classes: Resulting classes of attached devices
+ *
+ *	Reset PATA phy and classify attached devices.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+static int piix_pata_probe_reset(struct ata_port *ap, unsigned int *classes)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
 
 	if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->hard_port_no])) {
-		ata_port_disable(ap);
 		printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
-		return;
+		return 0;
 	}
 
-	piix_pata_cbl_detect(ap);
-
-	ata_port_probe(ap);
-
-	ata_bus_reset(ap);
+	return ata_drive_probe_reset(ap, ata_std_probeinit,
+				     ata_std_softreset, NULL,
+				     piix_pata_postreset, classes);
 }
 
 /**
author
#1 lore raw

PATCH 1/1 ata_piix: convert sata to new reset mechanism

[PATCH] ata_piix: convert sata to new reset mechanism

Convert ata_piix sata ->phy_reset to new reset mechanism.

---

 ata_piix.c |   35 +++++++++++++++--------------------
 1 file changed, 15 insertions(+), 20 deletions(-)
drivers/scsi/ata_piix.c +15 -20
Index: work1/drivers/scsi/ata_piix.c
===================================================================
@@ -132,7 +132,7 @@ static int piix_init_one (struct pci_dev
 				    const struct pci_device_id *ent);
 
 static int piix_pata_probe_reset(struct ata_port *ap, unsigned int *classes);
-static void piix_sata_phy_reset(struct ata_port *ap);
+static int piix_sata_probe_reset(struct ata_port *ap, unsigned int *classes);
 static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
 static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
 
@@ -236,7 +236,7 @@ static const struct ata_port_operations 
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
 
-	.phy_reset		= piix_sata_phy_reset,
+	.probe_reset		= piix_sata_probe_reset,
 
 	.bmdma_setup		= ata_bmdma_setup,
 	.bmdma_start		= ata_bmdma_start,
@@ -273,8 +273,8 @@ static struct ata_port_info piix_port_in
 	/* ich5_sata */
 	{
 		.sht		= &piix_sht,
-		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_SRST |
-				  PIIX_FLAG_COMBINED | PIIX_FLAG_CHECKINTR,
+		.host_flags	= ATA_FLAG_SATA | PIIX_FLAG_COMBINED |
+				  PIIX_FLAG_CHECKINTR,
 		.pio_mask	= 0x1f,	/* pio0-4 */
 		.mwdma_mask	= 0x07, /* mwdma0-2 */
 		.udma_mask	= 0x7f,	/* udma0-6 */
@@ -298,8 +298,7 @@ static struct ata_port_info piix_port_in
 	/* ich6_sata */
 	{
 		.sht		= &piix_sht,
-		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_SRST |
-				  PIIX_FLAG_COMBINED_ICH6 |
+		.host_flags	= ATA_FLAG_SATA | PIIX_FLAG_COMBINED_ICH6 |
 				  PIIX_FLAG_CHECKINTR | ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= 0x1f,	/* pio0-4 */
 		.mwdma_mask	= 0x07, /* mwdma0-2 */
@@ -310,8 +309,7 @@ static struct ata_port_info piix_port_in
 	/* ich6_sata_ahci */
 	{
 		.sht		= &piix_sht,
-		.host_flags	= ATA_FLAG_SATA | ATA_FLAG_SRST |
-				  PIIX_FLAG_COMBINED_ICH6 |
+		.host_flags	= ATA_FLAG_SATA | PIIX_FLAG_COMBINED_ICH6 |
 				  PIIX_FLAG_CHECKINTR | ATA_FLAG_SLAVE_POSS |
 				  PIIX_FLAG_AHCI,
 		.pio_mask	= 0x1f,	/* pio0-4 */
@@ -453,28 +451,25 @@ static int piix_sata_probe (struct ata_p
 }
 
 /**
- *	piix_sata_phy_reset - Probe specified port on SATA host controller
- *	@ap: Port to probe
+ *	piix_sata_probe_reset - Perform reset on SATA port and classify
+ *	@ap: Port to reset
+ *	@classes: Resulting classes of attached devices
  *
- *	Probe SATA phy.
+ *	Reset SATA phy and classify attached devices.
  *
  *	LOCKING:
  *	None (inherited from caller).
  */
-
-static void piix_sata_phy_reset(struct ata_port *ap)
+static int piix_sata_probe_reset(struct ata_port *ap, unsigned int *classes)
 {
 	if (!piix_sata_probe(ap)) {
-		ata_port_disable(ap);
 		printk(KERN_INFO "ata%u: SATA port has no device.\n", ap->id);
-		return;
+		return 0;
 	}
 
-	ap->cbl = ATA_CBL_SATA;
-
-	ata_port_probe(ap);
-
-	ata_bus_reset(ap);
+	return ata_drive_probe_reset(ap, ata_std_probeinit,
+				     ata_std_softreset, NULL,
+				     ata_std_postreset, classes);
 }
 
 /**
#2 lore raw

Re: [PATCH] ata_piix: convert sata to new reset mechanism

Quoted 5 lines · Tejun Heo

[PATCH] ata_piix: convert sata to new reset mechanism

Convert ata_piix sata ->phy_reset to new reset mechanism.

OK, but dropped due to dropping last patch

#3 lore raw
In reply to Tejun Heo
Quoted 99 lines · Tejun Heo

[PATCH] ata_piix: convert pata to new reset mechanism

Convert ata_piix pata ->phy_reset to new reset mechanism.

--

Jeff, this patch assumes that all-probe_reset-to-return-UNKNOWN[1] is applied.

[1] http://article.gmane.org/gmane.linux.ide/7967

 ata_piix.c |   44 ++++++++++++++++++++++++++++----------------
 1 file changed, 28 insertions(+), 16 deletions(-)

Index: work1/drivers/scsi/ata_piix.c
===================================================================

drivers/scsi/ata_piix.c +25 -11
@@ -131,7 +131,7 @@ enum {
 static int piix_init_one (struct pci_dev *pdev,
 				    const struct pci_device_id *ent);
 
-static void piix_pata_phy_reset(struct ata_port *ap);
+static int piix_pata_probe_reset(struct ata_port *ap, unsigned int *classes);
 static void piix_sata_phy_reset(struct ata_port *ap);
 static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
 static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
@@ -208,7 +208,7 @@ static const struct ata_port_operations 
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
 
-	.phy_reset		= piix_pata_phy_reset,
+	.probe_reset		= piix_pata_probe_reset,
 
 	.bmdma_setup		= ata_bmdma_setup,
 	.bmdma_start		= ata_bmdma_start,
@@ -259,8 +259,7 @@ static struct ata_port_info piix_port_in
 	/* ich5_pata */
 	{
 		.sht		= &piix_sht,
-		.host_flags	= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST |
-				  PIIX_FLAG_CHECKINTR,
+		.host_flags	= ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
 		.pio_mask	= 0x1f,	/* pio0-4 */
 #if 0
 		.mwdma_mask	= 0x06, /* mwdma1-2 */
@@ -285,7 +284,7 @@ static struct ata_port_info piix_port_in
 	/* piix4_pata */
 	{
 		.sht		= &piix_sht,
-		.host_flags	= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+		.host_flags	= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= 0x1f,	/* pio0-4 */
 #if 0
 		.mwdma_mask	= 0x06, /* mwdma1-2 */
@@ -367,30 +366,43 @@ cbl40:
 }
 
 /**
- *	piix_pata_phy_reset - Probe specified port on PATA host controller
- *	@ap: Port to probe
+ *	piix_pata_postreset - Postreset stuff on PATA host controller
+ *	@ap: Target port
+ *	@classes: Classes of attached devices
  *
- *	Probe PATA phy.
+ *	Postreset processing including cable detection.
  *
  *	LOCKING:
  *	None (inherited from caller).
  */
+static void piix_pata_postreset(struct ata_port *ap, unsigned int *classes)
+{
+	piix_pata_cbl_detect(ap);
+	ata_std_postreset(ap, classes);
+}
 
-static void piix_pata_phy_reset(struct ata_port *ap)
+/**
+ *	piix_pata_probe_reset - Perform reset on PATA port and classify
+ *	@ap: Port to reset
+ *	@classes: Resulting classes of attached devices
+ *
+ *	Reset PATA phy and classify attached devices.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+static int piix_pata_probe_reset(struct ata_port *ap, unsigned int *classes)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
 
 	if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->hard_port_no])) {
-		ata_port_disable(ap);
 		printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
-		return;
+		return 0;

drivers/scsi/ata_piix.c cbl40: · line 405

Quoted 10 lines
drivers/scsi/ata_piix.c +3 -5
 	}
 
-	piix_pata_cbl_detect(ap);
-
-	ata_port_probe(ap);
-
-	ata_bus_reset(ap);
+	return ata_drive_probe_reset(ap, ata_std_probeinit,
+				     ata_std_softreset, NULL,
+				     piix_pata_postreset, classes);

NAK, changes order of operations. Cable detect moves from being one of the very first things to one of the very last things.

Jeff