Skip to contentSkip to conversation

kernel 2.6.15.4: soft lockup detected on CPU#0!

BUG In review Charles-Edouard Ruault 7 participants 22 messages Feb 12, 2006 – Mar 13, 2006

lore
Share & tools
lore
#0 lore raw

Hi All,
i was trying to rip a CD when the whole machine started to freeze periodicaly, i then looked at the logs and found the following :

Feb 12 19:23:39 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdd: status timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdd: drive not ready for command
Feb 12 19:23:39 ruault kernel: BUG: soft lockup detected on CPU#0!
Feb 12 19:23:39 ruault kernel:
Feb 12 19:23:39 ruault kernel: Pid: 0, comm:              swapper
Feb 12 19:23:39 ruault kernel: EIP: 0060:[<c0272b75>] CPU: 0
Feb 12 19:23:39 ruault kernel: EIP is at ide_inb+0x5/0x10
Feb 12 19:23:39 ruault kernel:  EFLAGS: 00000216    Tainted: P      
(2.6.15.4)
Feb 12 19:23:39 ruault kernel: EAX: 00000180 EBX: 01aefc21 ECX: cfd3beae
EDX: 00000177
Feb 12 19:23:39 ruault kernel: ESI: 00000088 EDI: c0419e30 EBP: c0419ec4
DS: 007b ES: 007b
Feb 12 19:23:39 ruault kernel: CR0: 8005003b CR2: b7274c4c CR3: 2086e000
CR4: 000006d0
Feb 12 19:23:39 ruault kernel:  [<c0273656>] ide_wait_stat+0xf6/0x140
Feb 12 19:23:39 ruault kernel:  [<c0271cf6>] start_request+0xe6/0x2e0
Feb 12 19:23:39 ruault kernel:  [<c027220b>] ide_do_request+0x2eb/0x400
Feb 12 19:23:39 ruault kernel:  [<c0280ff0>] cdrom_newpc_intr+0x0/0x470
Feb 12 19:23:39 ruault kernel:  [<c027255c>] ide_timer_expiry+0xec/0x290
Feb 12 19:23:39 ruault kernel:  [<c0272470>] ide_timer_expiry+0x0/0x290
Feb 12 19:23:39 ruault kernel:  [<c0128afc>] run_timer_softirq+0xbc/0x210
Feb 12 19:23:39 ruault kernel:  [<c0123f12>] __do_softirq+0x52/0xa0
Feb 12 19:23:39 ruault kernel:  [<c0123f8d>] do_softirq+0x2d/0x40
Feb 12 19:23:39 ruault kernel:  [<c0124068>] irq_exit+0x38/0x40
Feb 12 19:23:39 ruault kernel:  [<c0105a77>] do_IRQ+0x37/0x70
Feb 12 19:23:39 ruault kernel:  [<c0103d4e>] common_interrupt+0x1a/0x20
Feb 12 19:23:39 ruault kernel:  [<c010105b>] default_idle+0x2b/0x60
Feb 12 19:23:39 ruault kernel:  [<c01010f5>] cpu_idle+0x45/0x80
Feb 12 19:23:39 ruault kernel:  [<c03b084f>] start_kernel+0x17f/0x1e0
Feb 12 19:23:39 ruault kernel:  [<c03b0390>] unknown_bootoption+0x0/0x1e0
Feb 12 19:23:39 ruault kernel: hdc: status timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdc: drive not ready for command
Feb 12 19:23:39 ruault kernel: hdd: status timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdd: drive not ready for command
Feb 12 19:23:39 ruault kernel: hdd: ATAPI reset complete
Feb 12 19:23:49 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
Feb 12 19:23:49 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:49 ruault kernel: hdd: status timeout: status=0x80 { Busy }
Feb 12 19:24:09 ruault kernel: hdc: irq timeout: status=0x80 { Busy }

After a few seconds, the whole machine was totally locked up and the only option i had was a hard reset.
I was able to reproduce it once more.

I'm running vanilla kernel 2.6.15.4 on an athlon 32 bits. here's generic info about my configuration :

processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 8
model name : AMD Athlon(TM) XP 2400+
stepping : 1
cpu MHz : 2000.448
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 4004.40

/sbin/lspci -v
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
Flags: bus master, 66Mhz, medium devsel, latency 0 Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <available only to root>

00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: d6800000-d7dfffff
Prefetchable memory behind bridge: d8000000-efffffff
Capabilities: <available only to root>

00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Flags: bus master, stepping, medium devsel, latency 32, IRQ 20 Memory at d6000000 (32-bit, non-prefetchable) [size=2K] I/O ports at b800 [size=128]
Capabilities: <available only to root>

00:08.0 RAID bus controller: Promise Technology, Inc. PDC20376 (FastTrak
376) (rev 02)

        Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
        Flags: bus master, 66Mhz, medium devsel, latency 96, IRQ 10
        I/O ports at b400 [size=64]
        I/O ports at b000 [size=16]
        I/O ports at a800 [size=128]
        Memory at d5800000 (32-bit, non-prefetchable) [size=4K]
        Memory at d5000000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: <available only to root>

00:09.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01)
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
Flags: bus master, fast devsel, latency 32, IRQ 16 Memory at d4800000 (32-bit, non-prefetchable) [size=8K] Expansion ROM at d7ff0000 [disabled] [size=16K]
Capabilities: <available only to root>

00:0d.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corporation EtherExpress PRO/100+ Management
Adapter

        Flags: bus master, medium devsel, latency 32, IRQ 17
        Memory at d4000000 (32-bit, non-prefetchable) [size=4K]
        I/O ports at a400 [size=64]
        Memory at d3800000 (32-bit, non-prefetchable) [size=1M]
        [virtual] Expansion ROM at 50000000 [disabled] [size=1M]
        Capabilities: <available only to root>

00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. VT6202 USB2.0 4 port controller
Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at a000 [size=32]
Capabilities: <available only to root>

00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. VT6202 USB2.0 4 port controller
Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at 9800 [size=32]
Capabilities: <available only to root>

00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. VT6202 USB2.0 4 port controller
Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at 9400 [size=32]
Capabilities: <available only to root>

00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
Flags: bus master, medium devsel, latency 32, IRQ 19 Memory at d3000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>

00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: <available only to root>

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. A7V8X / A7V333 motherboard
Flags: bus master, medium devsel, latency 32, IRQ 255 I/O ports at 9000 [size=16]
Capabilities: <available only to root>

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: ASUSTeK Computer Inc. A7V8X Motherboard (Realtek
ALC650 codec)
Flags: medium devsel, IRQ 18
I/O ports at e000 [size=256]
Capabilities: <available only to root>

01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro] (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro]
Flags: bus master, stepping, 66Mhz, medium devsel, latency 255,
IRQ 17

        Memory at e8000000 (32-bit, prefetchable) [size=128M]
        I/O ports at d800 [size=256]
        Memory at d7000000 (32-bit, non-prefetchable) [size=64K]
        Expansion ROM at e7fe0000 [disabled] [size=128K]
        Capabilities: <available only to root>

01:00.1 Display controller: ATI Technologies Inc Radeon R300 [Radeon 9500 Pro] (Secondary)
Subsystem: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro]
Flags: bus master, stepping, 66Mhz, medium devsel, latency 64 Memory at d8000000 (32-bit, prefetchable) [size=128M] Memory at d6800000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <available only to root>

/sbin/lsmod

Module                  Size  Used by
rfcomm                 36504  0
l2cap                  24196  5 rfcomm
bluetooth              44900  4 rfcomm,l2cap
deflate                 3328  0
zlib_deflate           23576  1 deflate
twofish                47104  0
serpent                20224  0
aes_i586               38272  0
blowfish                8192  0
des                    16384  0
lp                     10696  0
sha256                 10880  0
sha1                    2816  0
crypto_null             2560  0
xfrm4_tunnel            3204  0
ipcomp                  7176  0
esp4                    7168  0
ah4                     5632  0
af_key                 31248  0
autofs4                18052  1
vmnet                  35748  3
parport_pc             38852  1
parport                35528  2 lp,parport_pc
vmmon                 111468  0
sunrpc                139836  1
ipt_MARK                2432  1
iptable_mangle          2560  1
ipt_MASQUERADE          3072  1
iptable_nat             6916  1
ip_nat                 17068  2 ipt_MASQUERADE,iptable_nat
ipt_LOG                 6656  1
ipt_limit               2432  1
ipt_mark                1664  1
ipt_state               1920  1
ip_conntrack           48556  4 ipt_MASQUERADE,iptable_nat,ip_nat,ipt_state
nfnetlink               5272  2 ip_nat,ip_conntrack
iptable_filter          2560  1
ip_tables              21120  9
ipt_MARK,iptable_mangle,ipt_MASQUERADE,iptable_nat,ipt_LOG,ipt_limit,ipt_mark,ipt_state,iptable_filter
binfmt_misc             9864  1
fglrx                 454604  7
ipv6                  259840  23
sd_mod                 17296  0
dm_mod                 54072  0
video                  14468  0
button                  5264  0
ac                      3716  0
quickcam               77348  0
videodev                7936  1 quickcam
usbhid                 37344  0
usb_storage            32516  0
scsi_mod              126824  2 sd_mod,usb_storage
ohci1394               33460  0
ieee1394               92600  1 ohci1394
uhci_hcd               31888  0
ehci_hcd               33416  0
via_agp                 8320  1
agpgart                29768  2 fglrx,via_agp
shpchp                 44224  0
i2c_viapro              7828  0
i2c_core               18192  1 i2c_viapro
snd_via82xx            24468  4
snd_ac97_codec         94112  1 snd_via82xx
snd_ac97_bus            2176  1 snd_ac97_codec
snd_seq_dummy           3076  0
snd_seq_oss            34176  0
snd_seq_midi_event      6784  1 snd_seq_oss
snd_seq                52112  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_pcm_oss            50848  0
snd_mixer_oss          18048  1 snd_pcm_oss
snd_pcm                85128  5 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_timer              22788  3 snd_seq,snd_pcm
snd_page_alloc          8968  2 snd_via82xx,snd_pcm
snd_mpu401_uart         6784  1 snd_via82xx
snd_rawmidi            22176  1 snd_mpu401_uart
snd_seq_device          7436  4
snd_seq_dummy,snd_seq_oss,snd_seq,snd_rawmidi
snd                    49252  16
snd_via82xx,snd_ac97_codec,snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore               8416  1 snd
eepro100               27920  0
b44                    23948  0
mii                     5376  2 eepro100,b44
floppy                 60100  0
usbcore               120836  6

quickcam,usbhid,usb_storage,uhci_hcd,ehci_hcd

relevant info regarding drives etc :

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

Feb 12 19:37:12 ruault kernel: VP_IDE: IDE controller at PCI slot
0000:00:11.1
Feb 12 19:37:12 ruault kernel: ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
Feb 12 19:37:12 ruault kernel: PCI: Via IRQ fixup for 0000:00:11.1, from
255 to 15
Feb 12 19:37:12 ruault kernel: VP_IDE: chipset revision 6
Feb 12 19:37:12 ruault kernel: VP_IDE: not 100% native mode: will probe
irqs later
Feb 12 19:37:12 ruault kernel: VP_IDE: VIA vt8235 (rev 00) IDE UDMA133
controller on pci0000:00:11.1
Feb 12 19:37:12 ruault kernel:     ide0: BM-DMA at 0x9000-0x9007, BIOS
settings: hda:DMA, hdb:pio
Feb 12 19:37:12 ruault kernel:     ide1: BM-DMA at 0x9008-0x900f, BIOS
settings: hdc:DMA, hdd:DMA
Feb 12 19:37:12 ruault kernel: hda: Maxtor 6Y080L0, ATA DISK drive
Feb 12 19:37:12 ruault kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Feb 12 19:37:12 ruault kernel: hdc: PLEXTOR CD-R PX-W1610A, ATAPI
CD/DVD-ROM drive
Feb 12 19:37:12 ruault kernel: hdd: _NEC DVD_RW ND-3500AG, ATAPI
CD/DVD-ROM drive
Feb 12 19:37:12 ruault kernel: ide1 at 0x170-0x177,0x376 on irq 15
Feb 12 19:37:12 ruault kernel: hda: max request size: 128KiB
Feb 12 19:37:12 ruault kernel: hda: 160086528 sectors (81964 MB)
w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
Feb 12 19:37:12 ruault kernel: hda: cache flushes supported
Feb 12 19:37:12 ruault kernel:  hda: hda1 hda2 hda3 hda4 < hda5 hda6
hda7 hda8 hda9 hda10 >
Feb 12 19:37:12 ruault kernel: hdc: ATAPI 40X CD-ROM CD-R/RW drive,
2048kB Cache, DMA
Feb 12 19:37:12 ruault kernel: Uniform CD-ROM driver Revision: 3.20
Feb 12 19:37:12 ruault kernel: hdd: ATAPI 32X DVD-ROM DVD-R CD-R/RW
drive, 2048kB Cache, UDMA(33)
Feb 12 19:37:12 ruault kernel: ide-floppy driver 0.99.newide

I'm also attaching my kernel config.

Let me know if you need anything else to troobleshoot the problem. Regards.

PS: i'm not on the list so please CC me when answering ! Thanks

Signature · 2 lines
Charles-Edouard Ruault
PGP Key ID E4D2B80C
#1 lore raw

I've got the same soft lockups, not while cdrom access but when sa-learn runs (from spamassassin):

[189597.723886] BUG: soft lockup detected on CPU#0!
[189597.723960]
[189597.724007] Pid: 14, comm:            kblockd/0
[189597.724061] EIP: 0060:[<c022dacc>] CPU: 0
[189597.724117] EIP is at ide_pio_sector+0xb2/0xdf
[189597.724169]  EFLAGS: 00200206    Not tainted  (2.6.15.4-pwc-ara)
[189597.724225] EAX: c2188000 EBX: ebdc5600 ECX: 00000000 EDX: 00000005
[189597.724278] ESI: f7cf1000 EDI: c03f2780 EBP: c03f2814 DS: 007b ES: 007b
[189597.724374] CR0: 8005003b CR2: 4d5591e4 CR3: 003b2000 CR4: 000006d0
[189597.724456]  [<c022db2b>] ide_pio_multi+0x32/0x3b
[189597.724616]  [<c022ddd3>] task_out_intr+0xc3/0xe5
[189597.724782]  [<c01231de>] del_timer+0x56/0x58
[189597.725022]  [<c022dd10>] task_out_intr+0x0/0xe5
[189597.725172]  [<c02296df>] ide_intr+0xbe/0x139
[189597.725318]  [<c013a041>] handle_IRQ_event+0x26/0x59
[189597.725461]  [<c013a0f4>] __do_IRQ+0x80/0xe0
[189597.725600]  [<c0104dc6>] do_IRQ+0x36/0x66
[189597.725794]  [<c01034f2>] common_interrupt+0x1a/0x20
[189597.725935]  [<f886b0d4>] ipt_do_table+0xac/0x315 [ip_tables]
[189597.726098]  [<f88d1029>] ipt_hook+0x29/0x31 [iptable_filter]
[189597.726231]  [<c0286ff1>] nf_iterate+0x69/0x83
[189597.726359]  [<c028c893>] ip_local_deliver_finish+0x0/0x1cc
[189597.726568]  [<c028c893>] ip_local_deliver_finish+0x0/0x1cc
[189597.726696]  [<c0287068>] nf_hook_slow+0x5d/0xea
[189597.726831]  [<c028c893>] ip_local_deliver_finish+0x0/0x1cc
[189597.726972]  [<c028c328>] ip_local_deliver+0x220/0x250
[189597.727134]  [<c028c893>] ip_local_deliver_finish+0x0/0x1cc
[189597.727298]  [<c028c5ed>] ip_rcv+0x295/0x53b
[189597.727555]  [<c028ca5f>] ip_rcv_finish+0x0/0x295
[189597.727757]  [<c0273111>] netif_receive_skb+0x283/0x352
[189597.727930]  [<c0273266>] process_backlog+0x86/0x106
[189597.728081]  [<c027336e>] net_rx_action+0x88/0x160
[189597.728229]  [<c011fb34>] __do_softirq+0xbc/0xce
[189597.728443]  [<c011fb78>] do_softirq+0x32/0x34
[189597.728561]  [<c0104dcb>] do_IRQ+0x3b/0x66
[189597.728685]  [<c01034f2>] common_interrupt+0x1a/0x20
[189597.728817]  [<c0228e61>] start_request+0xfc/0x201
[189597.728955]  [<c0229190>] ide_do_request+0x209/0x351
[189597.729163]  [<c01c072a>] as_work_handler+0x40/0x42
[189597.729296]  [<c01297a6>] worker_thread+0x185/0x21a
[189597.729433]  [<c01c06ea>] as_work_handler+0x0/0x42
[189597.729570]  [<c011770a>] default_wake_function+0x0/0xc
[189597.729711]  [<c011770a>] default_wake_function+0x0/0xc
[189597.729856]  [<c0129621>] worker_thread+0x0/0x21a
[189597.730083]  [<c012d2ce>] kthread+0x9c/0xa1
[189597.730239]  [<c012d232>] kthread+0x0/0xa1
[189597.730419]  [<c0101065>] kernel_thread_helper+0x5/0xb
Quoted 326 lines · Charles-Edouard Ruault

Hi All,
i was trying to rip a CD when the whole machine started to freeze periodicaly, i then looked at the logs and found the following :

Feb 12 19:23:39 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdd: status timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdd: drive not ready for command
Feb 12 19:23:39 ruault kernel: BUG: soft lockup detected on CPU#0!
Feb 12 19:23:39 ruault kernel:
Feb 12 19:23:39 ruault kernel: Pid: 0, comm:              swapper
Feb 12 19:23:39 ruault kernel: EIP: 0060:[<c0272b75>] CPU: 0
Feb 12 19:23:39 ruault kernel: EIP is at ide_inb+0x5/0x10
Feb 12 19:23:39 ruault kernel:  EFLAGS: 00000216    Tainted: P      
(2.6.15.4)
Feb 12 19:23:39 ruault kernel: EAX: 00000180 EBX: 01aefc21 ECX: cfd3beae
EDX: 00000177
Feb 12 19:23:39 ruault kernel: ESI: 00000088 EDI: c0419e30 EBP: c0419ec4
DS: 007b ES: 007b
Feb 12 19:23:39 ruault kernel: CR0: 8005003b CR2: b7274c4c CR3: 2086e000
CR4: 000006d0
Feb 12 19:23:39 ruault kernel:  [<c0273656>] ide_wait_stat+0xf6/0x140
Feb 12 19:23:39 ruault kernel:  [<c0271cf6>] start_request+0xe6/0x2e0
Feb 12 19:23:39 ruault kernel:  [<c027220b>] ide_do_request+0x2eb/0x400
Feb 12 19:23:39 ruault kernel:  [<c0280ff0>] cdrom_newpc_intr+0x0/0x470
Feb 12 19:23:39 ruault kernel:  [<c027255c>] ide_timer_expiry+0xec/0x290
Feb 12 19:23:39 ruault kernel:  [<c0272470>] ide_timer_expiry+0x0/0x290
Feb 12 19:23:39 ruault kernel:  [<c0128afc>] run_timer_softirq+0xbc/0x210
Feb 12 19:23:39 ruault kernel:  [<c0123f12>] __do_softirq+0x52/0xa0
Feb 12 19:23:39 ruault kernel:  [<c0123f8d>] do_softirq+0x2d/0x40
Feb 12 19:23:39 ruault kernel:  [<c0124068>] irq_exit+0x38/0x40
Feb 12 19:23:39 ruault kernel:  [<c0105a77>] do_IRQ+0x37/0x70
Feb 12 19:23:39 ruault kernel:  [<c0103d4e>] common_interrupt+0x1a/0x20
Feb 12 19:23:39 ruault kernel:  [<c010105b>] default_idle+0x2b/0x60
Feb 12 19:23:39 ruault kernel:  [<c01010f5>] cpu_idle+0x45/0x80
Feb 12 19:23:39 ruault kernel:  [<c03b084f>] start_kernel+0x17f/0x1e0
Feb 12 19:23:39 ruault kernel:  [<c03b0390>] unknown_bootoption+0x0/0x1e0
Feb 12 19:23:39 ruault kernel: hdc: status timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdc: drive not ready for command
Feb 12 19:23:39 ruault kernel: hdd: status timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdd: drive not ready for command
Feb 12 19:23:39 ruault kernel: hdd: ATAPI reset complete
Feb 12 19:23:49 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
Feb 12 19:23:49 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:49 ruault kernel: hdd: status timeout: status=0x80 { Busy }
Feb 12 19:24:09 ruault kernel: hdc: irq timeout: status=0x80 { Busy }

After a few seconds, the whole machine was totally locked up and the only option i had was a hard reset.
I was able to reproduce it once more.

I'm running vanilla kernel 2.6.15.4 on an athlon 32 bits. here's generic info about my configuration :

processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 8
model name : AMD Athlon(TM) XP 2400+
stepping : 1
cpu MHz : 2000.448
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 4004.40

/sbin/lspci -v
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
Flags: bus master, 66Mhz, medium devsel, latency 0 Memory at f0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <available only to root>

00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: d6800000-d7dfffff
Prefetchable memory behind bridge: d8000000-efffffff
Capabilities: <available only to root>

00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Flags: bus master, stepping, medium devsel, latency 32, IRQ 20 Memory at d6000000 (32-bit, non-prefetchable) [size=2K] I/O ports at b800 [size=128]
Capabilities: <available only to root>

00:08.0 RAID bus controller: Promise Technology, Inc. PDC20376 (FastTrak
376) (rev 02)

        Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
        Flags: bus master, 66Mhz, medium devsel, latency 96, IRQ 10
        I/O ports at b400 [size=64]
        I/O ports at b000 [size=16]
        I/O ports at a800 [size=128]
        Memory at d5800000 (32-bit, non-prefetchable) [size=4K]
        Memory at d5000000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: <available only to root>

00:09.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01)
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
Flags: bus master, fast devsel, latency 32, IRQ 16 Memory at d4800000 (32-bit, non-prefetchable) [size=8K] Expansion ROM at d7ff0000 [disabled] [size=16K]
Capabilities: <available only to root>

00:0d.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Intel Corporation EtherExpress PRO/100+ Management
Adapter

        Flags: bus master, medium devsel, latency 32, IRQ 17
        Memory at d4000000 (32-bit, non-prefetchable) [size=4K]
        I/O ports at a400 [size=64]
        Memory at d3800000 (32-bit, non-prefetchable) [size=1M]
        [virtual] Expansion ROM at 50000000 [disabled] [size=1M]
        Capabilities: <available only to root>

00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. VT6202 USB2.0 4 port controller
Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at a000 [size=32]
Capabilities: <available only to root>

00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. VT6202 USB2.0 4 port controller
Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at 9800 [size=32]
Capabilities: <available only to root>

00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. VT6202 USB2.0 4 port controller
Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at 9400 [size=32]
Capabilities: <available only to root>

00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
Flags: bus master, medium devsel, latency 32, IRQ 19 Memory at d3000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>

00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: <available only to root>

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. A7V8X / A7V333 motherboard
Flags: bus master, medium devsel, latency 32, IRQ 255 I/O ports at 9000 [size=16]
Capabilities: <available only to root>

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: ASUSTeK Computer Inc. A7V8X Motherboard (Realtek
ALC650 codec)
Flags: medium devsel, IRQ 18
I/O ports at e000 [size=256]
Capabilities: <available only to root>

01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro] (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro]
Flags: bus master, stepping, 66Mhz, medium devsel, latency 255,
IRQ 17

        Memory at e8000000 (32-bit, prefetchable) [size=128M]
        I/O ports at d800 [size=256]
        Memory at d7000000 (32-bit, non-prefetchable) [size=64K]
        Expansion ROM at e7fe0000 [disabled] [size=128K]
        Capabilities: <available only to root>

01:00.1 Display controller: ATI Technologies Inc Radeon R300 [Radeon 9500 Pro] (Secondary)
Subsystem: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro]
Flags: bus master, stepping, 66Mhz, medium devsel, latency 64 Memory at d8000000 (32-bit, prefetchable) [size=128M] Memory at d6800000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <available only to root>

/sbin/lsmod

Module                  Size  Used by
rfcomm                 36504  0
l2cap                  24196  5 rfcomm
bluetooth              44900  4 rfcomm,l2cap
deflate                 3328  0
zlib_deflate           23576  1 deflate
twofish                47104  0
serpent                20224  0
aes_i586               38272  0
blowfish                8192  0
des                    16384  0
lp                     10696  0
sha256                 10880  0
sha1                    2816  0
crypto_null             2560  0
xfrm4_tunnel            3204  0
ipcomp                  7176  0
esp4                    7168  0
ah4                     5632  0
af_key                 31248  0
autofs4                18052  1
vmnet                  35748  3
parport_pc             38852  1
parport                35528  2 lp,parport_pc
vmmon                 111468  0
sunrpc                139836  1
ipt_MARK                2432  1
iptable_mangle          2560  1
ipt_MASQUERADE          3072  1
iptable_nat             6916  1
ip_nat                 17068  2 ipt_MASQUERADE,iptable_nat
ipt_LOG                 6656  1
ipt_limit               2432  1
ipt_mark                1664  1
ipt_state               1920  1
ip_conntrack           48556  4 ipt_MASQUERADE,iptable_nat,ip_nat,ipt_state
nfnetlink               5272  2 ip_nat,ip_conntrack
iptable_filter          2560  1
ip_tables              21120  9
ipt_MARK,iptable_mangle,ipt_MASQUERADE,iptable_nat,ipt_LOG,ipt_limit,ipt_mark,ipt_state,iptable_filter
binfmt_misc             9864  1
fglrx                 454604  7
ipv6                  259840  23
sd_mod                 17296  0
dm_mod                 54072  0
video                  14468  0
button                  5264  0
ac                      3716  0
quickcam               77348  0
videodev                7936  1 quickcam
usbhid                 37344  0
usb_storage            32516  0
scsi_mod              126824  2 sd_mod,usb_storage
ohci1394               33460  0
ieee1394               92600  1 ohci1394
uhci_hcd               31888  0
ehci_hcd               33416  0
via_agp                 8320  1
agpgart                29768  2 fglrx,via_agp
shpchp                 44224  0
i2c_viapro              7828  0
i2c_core               18192  1 i2c_viapro
snd_via82xx            24468  4
snd_ac97_codec         94112  1 snd_via82xx
snd_ac97_bus            2176  1 snd_ac97_codec
snd_seq_dummy           3076  0
snd_seq_oss            34176  0
snd_seq_midi_event      6784  1 snd_seq_oss
snd_seq                52112  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_pcm_oss            50848  0
snd_mixer_oss          18048  1 snd_pcm_oss
snd_pcm                85128  5 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_timer              22788  3 snd_seq,snd_pcm
snd_page_alloc          8968  2 snd_via82xx,snd_pcm
snd_mpu401_uart         6784  1 snd_via82xx
snd_rawmidi            22176  1 snd_mpu401_uart
snd_seq_device          7436  4
snd_seq_dummy,snd_seq_oss,snd_seq,snd_rawmidi
snd                    49252  16
snd_via82xx,snd_ac97_codec,snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore               8416  1 snd
eepro100               27920  0
b44                    23948  0
mii                     5376  2 eepro100,b44
floppy                 60100  0
usbcore               120836  6

quickcam,usbhid,usb_storage,uhci_hcd,ehci_hcd

relevant info regarding drives etc :

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

Feb 12 19:37:12 ruault kernel: VP_IDE: IDE controller at PCI slot
0000:00:11.1
Feb 12 19:37:12 ruault kernel: ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
Feb 12 19:37:12 ruault kernel: PCI: Via IRQ fixup for 0000:00:11.1, from
255 to 15
Feb 12 19:37:12 ruault kernel: VP_IDE: chipset revision 6
Feb 12 19:37:12 ruault kernel: VP_IDE: not 100% native mode: will probe
irqs later
Feb 12 19:37:12 ruault kernel: VP_IDE: VIA vt8235 (rev 00) IDE UDMA133
controller on pci0000:00:11.1
Feb 12 19:37:12 ruault kernel:     ide0: BM-DMA at 0x9000-0x9007, BIOS
settings: hda:DMA, hdb:pio
Feb 12 19:37:12 ruault kernel:     ide1: BM-DMA at 0x9008-0x900f, BIOS
settings: hdc:DMA, hdd:DMA
Feb 12 19:37:12 ruault kernel: hda: Maxtor 6Y080L0, ATA DISK drive
Feb 12 19:37:12 ruault kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Feb 12 19:37:12 ruault kernel: hdc: PLEXTOR CD-R PX-W1610A, ATAPI
CD/DVD-ROM drive
Feb 12 19:37:12 ruault kernel: hdd: _NEC DVD_RW ND-3500AG, ATAPI
CD/DVD-ROM drive
Feb 12 19:37:12 ruault kernel: ide1 at 0x170-0x177,0x376 on irq 15
Feb 12 19:37:12 ruault kernel: hda: max request size: 128KiB
Feb 12 19:37:12 ruault kernel: hda: 160086528 sectors (81964 MB)
w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
Feb 12 19:37:12 ruault kernel: hda: cache flushes supported
Feb 12 19:37:12 ruault kernel:  hda: hda1 hda2 hda3 hda4 < hda5 hda6
hda7 hda8 hda9 hda10 >
Feb 12 19:37:12 ruault kernel: hdc: ATAPI 40X CD-ROM CD-R/RW drive,
2048kB Cache, DMA
Feb 12 19:37:12 ruault kernel: Uniform CD-ROM driver Revision: 3.20
Feb 12 19:37:12 ruault kernel: hdd: ATAPI 32X DVD-ROM DVD-R CD-R/RW
drive, 2048kB Cache, UDMA(33)
Feb 12 19:37:12 ruault kernel: ide-floppy driver 0.99.newide
Quoted 12 lines

I'm also attaching my kernel config.

Let me know if you need anything else to troobleshoot the problem. Regards.

PS: i'm not on the list so please CC me when answering ! Thanks

Signature · 2 lines
Charles-Edouard Ruault
PGP Key ID E4D2B80C

Folkert van Heusden

Signature · 4 lines
www.vanheusden.com/multitail - multitail is tail on steroids. multiple
               windows, filtering, coloring, anything you can think of
----------------------------------------------------------------------
Phone: +31-6-41278122, PGP-key: 1F28D8AE, www.vanheusden.com
#2 lore raw
Quoted 2 lines · Folkert van Heusden

I've got the same soft lockups, not while cdrom access but when sa-learn runs (from spamassassin):

Why is DMA disabled for your IDE disks?

Lee

#3 lore raw
Quoted 3 lines
Quoted 2 lines

I've got the same soft lockups, not while cdrom access but when sa-learn runs (from spamassassin):

Why is DMA disabled for your IDE disks?

root@muur:/var/www/htdocs# hdparm -i /dev/hda

/dev/hda:

Model=QUANTUM FIREBALLP AS20.5, FwRev=A2R.0600, SerialNo=692124031358 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4 BuffType=DualPortCache, BuffSize=1902kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40132503 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:

* signifies the current active mode

On the other hand:

root@muur:/var/www/htdocs# hdparm -d /dev/hda

/dev/hda:
using_dma = 0 (off)

That is puzzling me as I explicitly swith that on in the startupscripts:
0 root@muur:/var/www/htdocs# grep hdparm /etc/rc.d/* /etc/rc.d/rc.local:/usr/sbin/hdparm -c 3 -d 1 -X 69 -u 1 /dev/hda &

So it seems it switches back to pio somewhere in time.

But on the other hand: shouldn't pio run ok as well without softlockup errors?

Folkert van Heusden

Signature · 3 lines
www.biglumber.com <- site where one can exchange PGP key signatures 
----------------------------------------------------------------------
Phone: +31-6-41278122, PGP-key: 1F28D8AE, www.vanheusden.com
#4 lore raw
Quoted 5 lines · Folkert van Heusden

So it seems it switches back to pio somewhere in time.

But on the other hand: shouldn't pio run ok as well without softlockup errors?

AFAICT in PIO mode if a huge IO request is submitted and/or the device is slow to respond there's nothing to prevent us spending a long time in the IDE driver.

IIRC this can't be made preemptible due to data corruption issues on some hardware. Maybe we should touch the watchdog in there.

Lee

#5 lore raw
Quoted 3 lines · Lee Revell

AFAICT in PIO mode if a huge IO request is submitted and/or the device is slow to respond there's nothing to prevent us spending a long time in the IDE driver.

IDE is basically bits of ISA bus decode stuffed down a cable and then sped up/fancified later. In PIO0 each cycle is pretty slow and we may issue quite a few in one transfer. If IORDY is enabled as is normally the case the drive also has the power to tell us to shut up and can do so for as long as it likes.

Quoted 2 lines

IIRC this can't be made preemptible due to data corruption issues on some hardware. Maybe we should touch the watchdog in there.

Some chips disable IRQs here and need to so that the stream of data doesn't stall and stuff fall apart. Touching the watchdog would be sensible.

Possibly the same is needed in the new libata pata bits too

#6 lore raw
Quoted 5 lines · Alan Cox

Some chips disable IRQs here and need to so that the stream of data doesn't stall and stuff fall apart. Touching the watchdog would be sensible.

Possibly the same is needed in the new libata pata bits too

Are you saying this might hit on non-legacy, non-broken hardware?

Lee

#7 lore raw
In reply to Charles-Edouard Ruault
Quoted 9 lines · Charles-Edouard Ruault

i was trying to rip a CD when the whole machine started to freeze
periodicaly, i then looked at the logs and found the following :

 Feb 12 19:23:39 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
 Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
 Feb 12 19:23:39 ruault kernel: hdd: status timeout: status=0x80 { Busy }
 Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
 Feb 12 19:23:39 ruault kernel: hdd: drive not ready for command

No idea what caused that.

Quoted 1 line
 Feb 12 19:23:39 ruault kernel: BUG: soft lockup detected on CPU#0!

The following was merged today. Hopefully it suppresses this false positive.

drivers/ide/ide-taskfile.c renamed from drivers/ide/ide-taskfile.c~ide-touch-softlockup-detector-during-pio +3 -0
@@ -34,6 +34,7 @@
 #include <linux/kernel.h>
 #include <linux/timer.h>
 #include <linux/mm.h>
+#include <linux/sched.h>
 #include <linux/interrupt.h>
 #include <linux/major.h>
 #include <linux/errno.h>
@@ -314,6 +315,8 @@ static void ide_pio_datablock(ide_drive_
 	if (rq->bio)	/* fs request */
 		rq->errors = 0;
 
+	touch_softlockup_watchdog();
+
 	switch (drive->hwif->data_phase) {
 	case TASKFILE_MULTI_IN:
 	case TASKFILE_MULTI_OUT:

_

#8 lore raw
Quoted 22 lines · Andrew Morton
Quoted 10 lines · Charles-Edouard Ruault

i was trying to rip a CD when the whole machine started to freeze periodicaly, i then looked at the logs and found the following :

Feb 12 19:23:39 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdd: status timeout: status=0x80 { Busy }
Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
Feb 12 19:23:39 ruault kernel: hdd: drive not ready for command

No idea what caused that.

Quoted 3 lines
Feb 12 19:23:39 ruault kernel: BUG: soft lockup detected on CPU#0!
Quoted 5 lines

The following was merged today. Hopefully it suppresses this false positive.

From what i understand it will fix the problem only if the drive is in

PIO mode, which is the case for Folkert van Heusden, who reported the same BUG output.
However it does not appear that my cdrom drives are using PIO, from the logs i have they're supposed to use DMA :

Quoted 4 lines
Feb 12 19:37:12 ruault kernel: hdc: ATAPI 40X CD-ROM CD-R/RW drive,2048kB Cache, DMA
Feb 12 19:37:12 ruault kernel: Uniform CD-ROM driver Revision: 3.20
Feb 12 19:37:12 ruault kernel: hdd: ATAPI 32X DVD-ROM DVD-R CD-R/RW

drive, 2048kB Cache, UDMA(33)

sudo /sbin/hdparm -i /dev/hdc

/dev/hdc:

Model=PLEXTOR CD-R PX-W1610A, FwRev=1.05, SerialNo= Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic } RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0 IORDY=on/off, tPIO={min:180,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2 AdvancedPM=no

sudo /sbin/hdparm -i /dev/hdd

/dev/hdd:

Model=_NEC DVD_RW ND-3500AG, FwRev=2.1A, SerialNo= Config={ Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic } RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=0kB, MaxMultSect=0 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0 IORDY=yes, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no

So i think this patch won't do me any good :(
any other idea ????

Thanks for the answer.

Signature · 2 lines
Charles-Edouard Ruault
GPG key Id E4D2B80C
#9 lore raw
Quoted 5 lines

From what i understand it will fix the problem only if the drive is in PIO mode, which is the case for Folkert van Heusden, who reported the same BUG output.
However it does not appear that my cdrom drives are using PIO, from the logs i have they're supposed to use DMA :

Quoted 7 lines
Quoted 4 lines
Feb 12 19:37:12 ruault kernel: hdc: ATAPI 40X CD-ROM CD-R/RW drive,2048kB Cache, DMA
Feb 12 19:37:12 ruault kernel: Uniform CD-ROM driver Revision: 3.20
Feb 12 19:37:12 ruault kernel: hdd: ATAPI 32X DVD-ROM DVD-R CD-R/RW

drive, 2048kB Cache, UDMA(33)

sudo /sbin/hdparm -i /dev/hdc
/dev/hdc:
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2

Try /sbin/hdparm -d /dev/hdc
and see if it returns "using_dma = 1 (on)".
I noticed that altough -i says using dma, that -d tells me it really is off.

Folkert van Heusden

Signature · 3 lines
www.biglumber.com <- site where one can exchange PGP key signatures 
----------------------------------------------------------------------
Phone: +31-6-41278122, PGP-key: 1F28D8AE, www.vanheusden.com
#10 lore raw
Quoted 3 lines · Folkert van Heusden

I noticed that altough -i says using dma, that -d tells me it really is
off.

Yup, `hdparm -i' tells you what the drive _can_ do, not what it's actually doing.

#11 lore raw
Quoted 13 lines · Andrew Morton
Quoted 4 lines · Folkert van Heusden

I noticed that altough -i says using dma, that -d tells me it really is off.

Yup, `hdparm -i' tells you what the drive _can_ do, not what it's actually doing.

here's what i have:

sudo /sbin/hdparm -d /dev/hdd
/dev/hdd:
using_dma = 1 (on)

sudo /sbin/hdparm -d /dev/hdc
/dev/hdc:
using_dma = 1 (on)

So it appears that both CDROM/DVDROM drives are using DMA, which confirms what i was thinking (since the traceback i have is not the same as the one Folker provided which clearly indicates that it happens during a pio operation ).

Signature · 2 lines
Charles-Edouard Ruault
GPG key Id E4D2B80C
#12 lore raw
In reply to Charles-Edouard Ruault
Quoted 3 lines · Charles-Edouard Ruault
Quoted 1 line

From what i understand it will fix the problem only if the drive is in

PIO mode, which is the case for Folkert van Heusden, who reported the same BUG output.

Timeouts will cause PIO fallbacks as the driver tries to beat the device back into sanity so it seems reasonable to expect the fix to work in this case.

#13 lore raw
In reply to Andrew Morton
Quoted 11 lines · Andrew Morton
Quoted 9 lines · Charles-Edouard Ruault

i was trying to rip a CD when the whole machine started to freeze
periodicaly, i then looked at the logs and found the following :

 Feb 12 19:23:39 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
 Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
 Feb 12 19:23:39 ruault kernel: hdd: status timeout: status=0x80 { Busy }
 Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
 Feb 12 19:23:39 ruault kernel: hdd: drive not ready for command
Quoted 6 lines

No idea what caused that.

Quoted 1 line
 Feb 12 19:23:39 ruault kernel: BUG: soft lockup detected on CPU#0!

The following was merged today. Hopefully it suppresses this false positive.

Unfortunately it won't. Charles' problem is different (and the BUG output is different!) - soft lockup got triggered for PIO handling in ide-cd driver. This patch fixes the problem only for generic ATA PIO routines (disks and [P]IDENTIFY), ATAPI PIO still needs fixing (ide-cd/floppy/tape/scsi drivers).

Andrew, there is no "high level" function for ATAPI PIO as ide_pio_datablock() for ATA PIO so fixing soft lockup false positives would require going through all drivers and adding bunch of touch_softlockup_watchdog() or using sledge-hammer approach and touching watchdog in ide-iops.c:atapi_[input,output]_bytes().

BTW Charles' OOPS is for tainted (P) kernel (fglrx loaded)

Bartlomiej

#14 lore raw
Quoted 17 lines · Bartlomiej Zolnierkiewicz
Quoted 15 lines · Andrew Morton
Quoted 9 lines · Charles-Edouard Ruault

i was trying to rip a CD when the whole machine started to freeze
periodicaly, i then looked at the logs and found the following :

 Feb 12 19:23:39 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
 Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
 Feb 12 19:23:39 ruault kernel: hdd: status timeout: status=0x80 { Busy }
 Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
 Feb 12 19:23:39 ruault kernel: hdd: drive not ready for command

No idea what caused that.

Quoted 1 line
 Feb 12 19:23:39 ruault kernel: BUG: soft lockup detected on CPU#0!
Quoted 8 lines
Quoted 2 lines

The following was merged today. Hopefully it suppresses this false positive.

Unfortunately it won't. Charles' problem is different (and the BUG output is different!) - soft lockup got triggered for PIO handling in ide-cd driver. This patch fixes the problem only for generic ATA PIO routines (disks and [P]IDENTIFY), ATAPI PIO still needs fixing (ide-cd/floppy/tape/scsi drivers).

argh. We do need to bop that warning on the head - it's consuming people's time and causing unneeded concern.

Quoted 5 lines

Andrew, there is no "high level" function for ATAPI PIO as ide_pio_datablock() for ATA PIO so fixing soft lockup false positives would require going through all drivers and adding bunch of touch_softlockup_watchdog() or using sledge-hammer approach and touching watchdog in ide-iops.c:atapi_[input,output]_bytes().

Send fixup patch, please?

#15 lore raw
Quoted 21 lines · Andrew Morton
Quoted 20 lines · Bartlomiej Zolnierkiewicz
Quoted 17 lines · Andrew Morton
Quoted 9 lines · Charles-Edouard Ruault

i was trying to rip a CD when the whole machine started to freeze
periodicaly, i then looked at the logs and found the following :

 Feb 12 19:23:39 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
 Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
 Feb 12 19:23:39 ruault kernel: hdd: status timeout: status=0x80 { Busy }
 Feb 12 19:23:39 ruault kernel: ide: failed opcode was: unknown
 Feb 12 19:23:39 ruault kernel: hdd: drive not ready for command

No idea what caused that.

Quoted 1 line
 Feb 12 19:23:39 ruault kernel: BUG: soft lockup detected on CPU#0!

The following was merged today. Hopefully it suppresses this false positive.

Quoted 8 lines
Quoted 5 lines

Unfortunately it won't. Charles' problem is different (and the BUG output is different!) - soft lockup got triggered for PIO handling in ide-cd driver. This patch fixes the problem only for generic ATA PIO routines (disks and [P]IDENTIFY), ATAPI PIO still needs fixing (ide-cd/floppy/tape/scsi drivers).

argh. We do need to bop that warning on the head - it's consuming people's time and causing unneeded concern.

Yes, it is definitely consuming time...
this is 3-rd time we hit false-positive in IDE subsystem.

"soft lockup during probe" problem was fixed by touching watchdog. I believe proper fix would require using msleep() instead of mdelay() and we knew this before soft lockup issue.

So from my IDE work POV it was just wasted time...

"ATA PIO" problem was handled in the same way.
I'm still not 100% sure if it was false positive - it looked like from the trace but I find it hard to believe that users wouldn't complain about 10sec stalls [ Soft lockup detector claims to trigger if after 10sec it hasn't been touched - is it really working as advertised? How can we verify this? ].

Again it only wasted time from IDE POV.

And now ATAPI PIO issues requires me to audit all ATAPI device drivers to quiet soft lockup detector...

Quoted 7 lines
Quoted 5 lines

Andrew, there is no "high level" function for ATAPI PIO as ide_pio_datablock() for ATA PIO so fixing soft lockup false positives would require going through all drivers and adding bunch of touch_softlockup_watchdog() or using sledge-hammer approach and touching watchdog in ide-iops.c:atapi_[input,output]_bytes().

Send fixup patch, please?

Other things have much bigger priority than quieting soft lockup detector because somebody decided upon driver maintainers that soft lockup during hardware access is a _major_ problem (-> system stays locked) and needs to be fixed ASAP (-> it is enabled by default).

This feature could be useful but why driver maintainers are _forced_ to pay maintenance cost for it?

I can send you another sledge-hammer fix which is quite disgusting as it touches watchdog on every ATAPI related PIO access (i.e. many times in ATAPI PIO IRQ handlers, during packet command transfer).

Alternatively I can send you patch making soft lockup detector depend on "CONFIG_IDE=n".

Bartlomiej

#16 lore raw

PATCH 1/1 timer-irq-driven soft-watchdog, cleanups

Quoted 5 lines · Bartlomiej Zolnierkiewicz

I'm still not 100% sure if it was false positive - it looked like from the trace but I find it hard to believe that users wouldn't complain about 10sec stalls [ Soft lockup detector claims to trigger if after 10sec it hasn't been touched - is it really working as advertised? How can we verify this? ].

the watchdog is quite simple: it consists of per-CPU SCHED_FIFO prio 99 [i.e. highest RT priority] threads that do nothing but:

        while (!kthread_should_stop()) {
                msleep_interruptible(1000);
                touch_softlockup_watchdog();
        }

i can think of only one (pretty theoretical) scenario for a false positive here: msleep uses timers, which are processed by softirq context, which context itself might be delayed. Under extreme load, if softirqs get delayed for more than 9 seconds, this _might_ lead to false positives. But that i think is highly unlikely in the reported IDE cases.

in any case, the patch below gets rid of the softirq involvement, and makes the soft-watchdog purely timer-irq driven (and a few minor cleanups). Could you try it? I have tested it - it correctly detected a 11-seconds delay and stayed silent during a 9-seconds delay.

If you still get warnings even with this patch applied, then my very strong suspicion is that the 10+ seconds delays in the IDE code are real, and not false-positives. If there are such places then the minimum we should do is to document them via touch_softlockup_watchdog() ... even if you "knew" about such places already.

Andrew, could we try this patch in -mm?

Ingo

---------------

this patch makes the softlockup detector purely timer-interrupt driven, removing softirq-context (timer) dependencies. This means that if the softlockup watchdog triggers, it has truly observed a longer than 10 seconds scheduling delay of a SCHED_FIFO prio 99 task.

(the patch also turns off the softlockup detector during the initial bootup phase and does small style fixes)

----

 kernel/softlockup.c |   47 +++++++++++++++++++++++------------------------
 1 files changed, 23 insertions(+), 24 deletions(-)
kernel/softlockup.c +23 -24
Index: linux/kernel/softlockup.c
===================================================================
@@ -1,12 +1,11 @@
 /*
  * Detect Soft Lockups
  *
- * started by Ingo Molnar, (C) 2005, Red Hat
+ * started by Ingo Molnar, Copyright (C) 2005, 2006 Red Hat, Inc.
  *
  * this code detects soft lockups: incidents in where on a CPU
  * the kernel does not reschedule for 10 seconds or more.
  */
-
 #include <linux/mm.h>
 #include <linux/cpu.h>
 #include <linux/init.h>
@@ -17,13 +16,14 @@
 
 static DEFINE_SPINLOCK(print_lock);
 
-static DEFINE_PER_CPU(unsigned long, timestamp) = 0;
-static DEFINE_PER_CPU(unsigned long, print_timestamp) = 0;
+static DEFINE_PER_CPU(unsigned long, touch_timestamp);
+static DEFINE_PER_CPU(unsigned long, print_timestamp);
 static DEFINE_PER_CPU(struct task_struct *, watchdog_task);
 
 static int did_panic = 0;
-static int softlock_panic(struct notifier_block *this, unsigned long event,
-				void *ptr)
+
+static int
+softlock_panic(struct notifier_block *this, unsigned long event, void *ptr)
 {
 	did_panic = 1;
 
@@ -36,7 +36,7 @@ static struct notifier_block panic_block
 
 void touch_softlockup_watchdog(void)
 {
-	per_cpu(timestamp, raw_smp_processor_id()) = jiffies;
+	per_cpu(touch_timestamp, raw_smp_processor_id()) = jiffies;
 }
 EXPORT_SYMBOL(touch_softlockup_watchdog);
 
@@ -47,17 +47,20 @@ EXPORT_SYMBOL(touch_softlockup_watchdog)
 void softlockup_tick(struct pt_regs *regs)
 {
 	int this_cpu = smp_processor_id();
-	unsigned long timestamp = per_cpu(timestamp, this_cpu);
-
-	if (per_cpu(print_timestamp, this_cpu) == timestamp)
-		return;
+	unsigned long touch_timestamp = per_cpu(touch_timestamp, this_cpu);
 
-	/* Do not cause a second panic when there already was one */
-	if (did_panic)
+	/* Do not warn during bootup and prevent double reports: */
+	if (system_state != SYSTEM_RUNNING || did_panic ||
+			per_cpu(print_timestamp, this_cpu) == touch_timestamp)
 		return;
 
-	if (time_after(jiffies, timestamp + 10*HZ)) {
-		per_cpu(print_timestamp, this_cpu) = timestamp;
+	/* Wake up the high-prio watchdog task every second: */
+	if (time_after(jiffies, touch_timestamp + HZ))
+		wake_up_process(per_cpu(watchdog_task, this_cpu));
+
+	/* Warn about unreasonable 10+ seconds delays: */
+	if (time_after(jiffies, touch_timestamp + 10*HZ)) {
+		per_cpu(print_timestamp, this_cpu) = touch_timestamp;
 
 		spin_lock(&print_lock);
 		printk(KERN_ERR "BUG: soft lockup detected on CPU#%d!\n",
@@ -77,18 +80,16 @@ static int watchdog(void * __bind_cpu)
 	sched_setscheduler(current, SCHED_FIFO, &param);
 	current->flags |= PF_NOFREEZE;
 
-	set_current_state(TASK_INTERRUPTIBLE);
-
 	/*
-	 * Run briefly once per second - if this gets delayed for
-	 * more than 10 seconds then the debug-printout triggers
-	 * in softlockup_tick():
+	 * Run briefly once per second to reset the softlockup timestamp.
+	 * If this gets delayed for more than 10 seconds then the
+	 * debug-printout triggers in softlockup_tick().
 	 */
 	while (!kthread_should_stop()) {
-		msleep_interruptible(1000);
+		set_current_state(TASK_INTERRUPTIBLE);
 		touch_softlockup_watchdog();
+		schedule();
 	}
-	__set_current_state(TASK_RUNNING);
 
 	return 0;
 }
@@ -114,7 +115,6 @@ cpu_callback(struct notifier_block *nfb,
 		kthread_bind(p, hotcpu);
  		break;
 	case CPU_ONLINE:
-
 		wake_up_process(per_cpu(watchdog_task, hotcpu));
 		break;
 #ifdef CONFIG_HOTPLUG_CPU
@@ -146,4 +146,3 @@ __init void spawn_softlockup_task(void)
 
 	notifier_chain_register(&panic_notifier_list, &panic_block);
 }
-
#17 lore raw

Re: [patch] timer-irq-driven soft-watchdog, cleanups

Quoted 17 lines · Ingo Molnar
Quoted 5 lines · Bartlomiej Zolnierkiewicz

I'm still not 100% sure if it was false positive - it looked like from the trace but I find it hard to believe that users wouldn't complain about 10sec stalls [ Soft lockup detector claims to trigger if after 10sec it hasn't been touched - is it really working as advertised? How can we verify this? ].

the watchdog is quite simple: it consists of per-CPU SCHED_FIFO prio 99 [i.e. highest RT priority] threads that do nothing but:

        while (!kthread_should_stop()) {
                msleep_interruptible(1000);
                touch_softlockup_watchdog();
        }
Quoted 6 lines

i can think of only one (pretty theoretical) scenario for a false positive here: msleep uses timers, which are processed by softirq context, which context itself might be delayed. Under extreme load, if softirqs get delayed for more than 9 seconds, this _might_ lead to false positives. But that i think is highly unlikely in the reported IDE cases.

Actually it seems very likely [ if I'm reading the code right ]: ide_intr() IRQ handler contains "optimization" that it calls ide_do_request() for the next request if the previous request is completed. Processing the next request involves waiting for device to become ready (up to 5sec) and sending first chunk of data out in case of PIO-out protocol. Moreover if the requests are short we can be hitting "optimization" case few times in the row. Hard IRQs will still have their chance to be processed but softirq context can be delayed quite a lot as it is executed after hard IRQ handler completes.

Quoted 10 lines

in any case, the patch below gets rid of the softirq involvement, and makes the soft-watchdog purely timer-irq driven (and a few minor cleanups). Could you try it? I have tested it - it correctly detected a 11-seconds delay and stayed silent during a 9-seconds delay.

If you still get warnings even with this patch applied, then my very strong suspicion is that the 10+ seconds delays in the IDE code are real, and not false-positives. If there are such places then the minimum we should do is to document them via touch_softlockup_watchdog() ... even if you "knew" about such places already.

Fully agreed, where is the patch?

Sorry but I have enough more high priority issues to take care of and I'm not going to spend any more time on soft lockups even if they are really problems in IDE subsystem. If this is not fixed before 2.6.16 I'm submitting patch to Linus making DETECT_SOFTLOCKUP depend on "CONFIG_IDE=n"... at least users will be able to use their systems instead of seeing lockups.

DETECT_SOFTLOCKUP should be an aim in development not a method of forcing driver maintainers to work on specific issues...

Thank you for understanding.

Bartlomiej

#18 lore raw

Re: [patch] timer-irq-driven soft-watchdog, cleanups

Quoted 7 lines · Bartlomiej Zolnierkiewicz
Quoted 5 lines

If you still get warnings even with this patch applied, then my very strong suspicion is that the 10+ seconds delays in the IDE code are real, and not false-positives. If there are such places then the minimum we should do is to document them via touch_softlockup_watchdog() ... even if you "knew" about such places already.

Fully agreed, where is the patch?

it's included in the mail you replied to :)

Ingo

#19 lore raw

Re: [patch] timer-irq-driven soft-watchdog, cleanups

In reply to Bartlomiej Zolnierkiewicz
Quoted 6 lines · Bartlomiej Zolnierkiewicz

Sorry but I have enough more high priority issues to take care of and I'm not going to spend any more time on soft lockups even if they are really problems in IDE subsystem. If this is not fixed before 2.6.16 I'm submitting patch to Linus making DETECT_SOFTLOCKUP depend on "CONFIG_IDE=n"... at least users will be able to use their systems instead of seeing lockups.

i have lots of IDE based systems (they dont use PIO though) and i'm not seeing these. I'll oppose such a patch if it's to hide genuine issues - the 10 seconds tolerance is already generous i think. I'll of course fix any false positives which are the fault of the softlockup-watchdog, but from your mails it appears to me that the IDE warnings are indeed genuine.

If the source of the delay is hard to fix you can temporarily work it around in the code by putting in the touch_softlockup_watchdog() lines - that will also document the places that cause long delays - which is a good thing.

It is entirely feasible to put a touch_softlockup_watchdog() call into every PIO OP - even a single-byte PIO related IN/OUT instruction takes a couple of microseconds, so a touch_softlockup_watchdog() wont even show up on the radar.

Quoted 2 lines

DETECT_SOFTLOCKUP should be an aim in development not a method of forcing driver maintainers to work on specific issues...

well, 10+ seconds delays on a running system are not really acceptable, and can cause other problems. The softlockup-watchdog is optional and can be easily turned off in the .config.

Ingo

#20 lore raw

Re: [patch] timer-irq-driven soft-watchdog, cleanups

Quoted 22 lines · Ingo Molnar
Quoted 6 lines · Bartlomiej Zolnierkiewicz

Sorry but I have enough more high priority issues to take care of and I'm not going to spend any more time on soft lockups even if they are really problems in IDE subsystem. If this is not fixed before 2.6.16 I'm submitting patch to Linus making DETECT_SOFTLOCKUP depend on "CONFIG_IDE=n"... at least users will be able to use their systems instead of seeing lockups.

i have lots of IDE based systems (they dont use PIO though) and i'm not seeing these. I'll oppose such a patch if it's to hide genuine issues - the 10 seconds tolerance is already generous i think. I'll of course fix any false positives which are the fault of the softlockup-watchdog, but from your mails it appears to me that the IDE warnings are indeed genuine.

If the source of the delay is hard to fix you can temporarily work it around in the code by putting in the touch_softlockup_watchdog() lines - that will also document the places that cause long delays - which is a good thing.

Quoted 4 lines

It is entirely feasible to put a touch_softlockup_watchdog() call into every PIO OP - even a single-byte PIO related IN/OUT instruction takes a couple of microseconds, so a touch_softlockup_watchdog() wont even show up on the radar.

OK, I'll just add touch_softlockup_watchdog() if needed but first lets wait for results of your patch.

Note that I'll invest my time on this which could be invested into other things and I don't see it as top-priority issue if you differ in your opinion you should be the person fixing affected drivers.

The conclusion of the rant is: people making changes at higher layers should start paying maintenance costs of their changes. Over few years of maintaining IDE I learned quite a lot about block layer, VFS, VM, ACPI, PM, IRQ routing, scheduling, sysfs etc (I'm not talking about interface changes but about bugs/changes which are reported by end users and driver maintainers are end-point). This is all good but distracts me from my primary task and now it is turn for people hacking on generic code to learn few driver specific things... :)

No wonder that nobody wants to hack drivers: less fame, more flames, and actually besides knowing hardware you need to know a lot about kernel in general to do your job right. I hope that Andrew is reading this.

End of whining.

Quoted 6 lines
Quoted 2 lines

DETECT_SOFTLOCKUP should be an aim in development not a method of forcing driver maintainers to work on specific issues...

well, 10+ seconds delays on a running system are not really acceptable, and can cause other problems. The softlockup-watchdog is optional and can be easily turned off in the .config.

It is "y" by default so anybody saying "y" to DEBUG_KERNEL will get it as added bonus and moreover DEBUG_KERNEL is "y" in x86_64 defconfig.

Bartlomiej

#21 lore raw

Re: [patch] timer-irq-driven soft-watchdog, cleanups

Quoted 68 lines · Bartlomiej Zolnierkiewicz
Quoted 24 lines · Ingo Molnar
Quoted 8 lines · Bartlomiej Zolnierkiewicz

Sorry but I have enough more high priority issues to take care of and I'm not going to spend any more time on soft lockups even if they are really problems in IDE subsystem. If this is not fixed before 2.6.16 I'm submitting patch to Linus making DETECT_SOFTLOCKUP depend on "CONFIG_IDE=n"... at least users will be able to use their systems instead of seeing lockups.

i have lots of IDE based systems (they dont use PIO though) and i'm not seeing these. I'll oppose such a patch if it's to hide genuine issues - the 10 seconds tolerance is already generous i think. I'll of course fix any false positives which are the fault of the softlockup-watchdog, but from your mails it appears to me that the IDE warnings are indeed genuine.

If the source of the delay is hard to fix you can temporarily work it around in the code by putting in the touch_softlockup_watchdog() lines - that will also document the places that cause long delays - which is a good thing.

Quoted 6 lines

It is entirely feasible to put a touch_softlockup_watchdog() call into every PIO OP - even a single-byte PIO related IN/OUT instruction takes a couple of microseconds, so a touch_softlockup_watchdog() wont even show up on the radar.

OK, I'll just add touch_softlockup_watchdog() if needed but first lets wait for results of your patch.

Note that I'll invest my time on this which could be invested into other things and I don't see it as top-priority issue if you differ in your opinion you should be the person fixing affected drivers.

The conclusion of the rant is: people making changes at higher layers should start paying maintenance costs of their changes. Over few years of maintaining IDE I learned quite a lot about block layer, VFS, VM, ACPI, PM, IRQ routing, scheduling, sysfs etc (I'm not talking about interface changes but about bugs/changes which are reported by end users and driver maintainers are end-point). This is all good but distracts me from my primary task and now it is turn for people hacking on generic code to learn few driver specific things... :)

No wonder that nobody wants to hack drivers: less fame, more flames, and actually besides knowing hardware you need to know a lot about kernel in general to do your job right. I hope that Andrew is reading this.

End of whining.

Quoted 9 lines
Quoted 4 lines

DETECT_SOFTLOCKUP should be an aim in development not a method of forcing driver maintainers to work on specific issues...

well, 10+ seconds delays on a running system are not really acceptable, and can cause other problems. The softlockup-watchdog is optional and can be easily turned off in the .config.

Quoted 6 lines

It is "y" by default so anybody saying "y" to DEBUG_KERNEL will get it as added bonus and moreover DEBUG_KERNEL is "y" in x86_64 defconfig.

Bartlomiej

Guys,
sorry for having been silent for so long ... since i had the problem, i upgraded to 2.6.15.6 and i experienced the problem again over the week-end. My point it that it appears that the BUG: soft lockup detected on CPU#0! message is legitimate in my case since my machine really freezes periodically because of ide timeouts.
What i'm trying to figure out is why are the IDE timeouts occuring ? Both my DVD burner & CD burner usually work fine ( i had been able to burn a DVD a few hours before the problem occured , i'm able to read CDs & DVDs fine ).
However, the problem seems to occur only when trying to rip CDs. It appears that both drives get confused .... ( see logs, both are reporting timeouts/erros ).

Mar 11 17:41:47 ruault kernel: hdd: ATAPI reset
complete                                                                   
Mar 11 17:41:57 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
Mar 11 17:41:57 ruault kernel: ide: failed opcode was:
unknown                                                             
Mar 11 17:41:57 ruault kernel: hdd: status timeout: status=0x80 { Busy }
Mar 11 17:41:57 ruault kernel: ide: failed opcode was:
unknown                                                             
Mar 11 17:41:57 ruault kernel: hdd: drive not ready for command
Mar 11 17:41:57 ruault kernel: hdd: ATAPI reset
complete                                                                   
Mar 11 17:42:17 ruault kernel: hdc: irq timeout: status=0x80 { Busy }
Mar 11 17:42:17 ruault kernel: ide: failed opcode was:
unknown                                                             
Mar 11 17:42:17 ruault kernel: hdd: status timeout: status=0x80 { Busy }
Mar 11 17:42:17 ruault kernel: ide: failed opcode was:
unknown                                                             
Mar 11 17:42:17 ruault kernel: hdd: drive not ready for command
Mar 11 17:42:17 ruault kernel: BUG: soft lockup detected on
CPU#0!                                                         
Mar 11 17:42:17 ruault kernel:
Mar 11 17:42:17 ruault kernel: Pid: 0, comm:             
swapper                                                          
Mar 11 17:42:17 ruault kernel: EIP: 0060:[<c0272c55>] CPU: 0
Mar 11 17:42:17 ruault kernel: EIP is at

ide_inb+0x5/0x10

Mar 11 17:42:17 ruault kernel:  EFLAGS: 00000206    Tainted: P      
(2.6.15.6)
Mar 11 17:42:17 ruault kernel: EAX: 00000180 EBX: 03aba395 ECX: f2b9d721
EDX: 00000177                                     
Mar 11 17:42:17 ruault kernel: ESI: 00000088 EDI: c0419e30 EBP: c0419ec4
DS: 007b ES: 007b
Mar 11 17:42:17 ruault kernel: CR0: 8005003b CR2: b7fe2000 CR3: 32e1b000

CR4: 000006d0

And i can confirm that when this happens the machine is totally unresponsive, as before i had to reboot the machine with a hard reset after a while.
So my question is what could be causing this behaviour ? is this a bug in the IDE driver ? a hardware problem with my drives ( as i said they appear to be working fine otherwise ), another hardware problem with my motherboard ?
What could i do to help troubleshoot the problem ?
Thanks in advance.

PS: I do not subscribe to the list so please CC me when replying ....

Signature · 2 lines
Charles-Edouard Ruault
GPG key Id E4D2B80C