Skip to contentSkip to conversation

Several recent libata commits

PATCH New Jeff Garzik 1 participant 1 message Mar 23, 2006

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Several recent libata commits

Linus pulled the latest stuff (incl. Alan and Tejun's stuff) already.

The 'upstream' branch of
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev.git

contains the following updates:

 drivers/scsi/libata-bmdma.c |  234 ++++++++++++++++++++++++++++++++++++++++++++
 drivers/scsi/libata-core.c  |  234 --------------------------------------------
 drivers/scsi/sata_nv.c      |  181 +++++++++++-----------------------
 drivers/scsi/sata_sil24.c   |   23 +---
 drivers/scsi/sata_uli.c     |   37 +++++-
 5 files changed, 333 insertions(+), 376 deletions(-)

Jeff Garzik:
[libata sata_sil24] cleanups: use pci_iomap(), kzalloc() [libata sata_nv] cleanups: convert #defines to enums; remove in-file history [libata sata_nv] eliminate duplicate codepaths with iomap [libata sata_uli] kill scr_addr abuse
[libata] Move some bmdma-specific code to libata-bmdma.c

drivers/scsi/libata-bmdma.c +234 -0
index 96b4d21..a00a78b 100644
@@ -418,6 +418,240 @@ u8 ata_altstatus(struct ata_port *ap)
 	return inb(ap->ioaddr.altstatus_addr);
 }
 
+/**
+ *	ata_bmdma_setup_mmio - Set up PCI IDE BMDMA transaction
+ *	@qc: Info associated with this ATA transaction.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ */
+
+static void ata_bmdma_setup_mmio (struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
+	u8 dmactl;
+	void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+
+	/* load PRD table addr. */
+	mb();	/* make sure PRD table writes are visible to controller */
+	writel(ap->prd_dma, mmio + ATA_DMA_TABLE_OFS);
+
+	/* specify data direction, triple-check start bit is clear */
+	dmactl = readb(mmio + ATA_DMA_CMD);
+	dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
+	if (!rw)
+		dmactl |= ATA_DMA_WR;
+	writeb(dmactl, mmio + ATA_DMA_CMD);
+
+	/* issue r/w command */
+	ap->ops->exec_command(ap, &qc->tf);
+}
+
+/**
+ *	ata_bmdma_start_mmio - Start a PCI IDE BMDMA transaction
+ *	@qc: Info associated with this ATA transaction.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ */
+
+static void ata_bmdma_start_mmio (struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+	u8 dmactl;
+
+	/* start host DMA transaction */
+	dmactl = readb(mmio + ATA_DMA_CMD);
+	writeb(dmactl | ATA_DMA_START, mmio + ATA_DMA_CMD);
+
+	/* Strictly, one may wish to issue a readb() here, to
+	 * flush the mmio write.  However, control also passes
+	 * to the hardware at this point, and it will interrupt
+	 * us when we are to resume control.  So, in effect,
+	 * we don't care when the mmio write flushes.
+	 * Further, a read of the DMA status register _immediately_
+	 * following the write may not be what certain flaky hardware
+	 * is expected, so I think it is best to not add a readb()
+	 * without first all the MMIO ATA cards/mobos.
+	 * Or maybe I'm just being paranoid.
+	 */
+}
+
+/**
+ *	ata_bmdma_setup_pio - Set up PCI IDE BMDMA transaction (PIO)
+ *	@qc: Info associated with this ATA transaction.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ */
+
+static void ata_bmdma_setup_pio (struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
+	u8 dmactl;
+
+	/* load PRD table addr. */
+	outl(ap->prd_dma, ap->ioaddr.bmdma_addr + ATA_DMA_TABLE_OFS);
+
+	/* specify data direction, triple-check start bit is clear */
+	dmactl = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+	dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
+	if (!rw)
+		dmactl |= ATA_DMA_WR;
+	outb(dmactl, ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+
+	/* issue r/w command */
+	ap->ops->exec_command(ap, &qc->tf);
+}
+
+/**
+ *	ata_bmdma_start_pio - Start a PCI IDE BMDMA transaction (PIO)
+ *	@qc: Info associated with this ATA transaction.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ */
+
+static void ata_bmdma_start_pio (struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	u8 dmactl;
+
+	/* start host DMA transaction */
+	dmactl = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+	outb(dmactl | ATA_DMA_START,
+	     ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+}
+
+
+/**
+ *	ata_bmdma_start - Start a PCI IDE BMDMA transaction
+ *	@qc: Info associated with this ATA transaction.
+ *
+ *	Writes the ATA_DMA_START flag to the DMA command register.
+ *
+ *	May be used as the bmdma_start() entry in ata_port_operations.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ */
+void ata_bmdma_start(struct ata_queued_cmd *qc)
+{
+	if (qc->ap->flags & ATA_FLAG_MMIO)
+		ata_bmdma_start_mmio(qc);
+	else
+		ata_bmdma_start_pio(qc);
+}
+
+
+/**
+ *	ata_bmdma_setup - Set up PCI IDE BMDMA transaction
+ *	@qc: Info associated with this ATA transaction.
+ *
+ *	Writes address of PRD table to device's PRD Table Address
+ *	register, sets the DMA control register, and calls
+ *	ops->exec_command() to start the transfer.
+ *
+ *	May be used as the bmdma_setup() entry in ata_port_operations.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ */
+void ata_bmdma_setup(struct ata_queued_cmd *qc)
+{
+	if (qc->ap->flags & ATA_FLAG_MMIO)
+		ata_bmdma_setup_mmio(qc);
+	else
+		ata_bmdma_setup_pio(qc);
+}
+
+
+/**
+ *	ata_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
+ *	@ap: Port associated with this ATA transaction.
+ *
+ *	Clear interrupt and error flags in DMA status register.
+ *
+ *	May be used as the irq_clear() entry in ata_port_operations.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ */
+
+void ata_bmdma_irq_clear(struct ata_port *ap)
+{
+	if (!ap->ioaddr.bmdma_addr)
+		return;
+
+	if (ap->flags & ATA_FLAG_MMIO) {
+		void __iomem *mmio =
+		      ((void __iomem *) ap->ioaddr.bmdma_addr) + ATA_DMA_STATUS;
+		writeb(readb(mmio), mmio);
+	} else {
+		unsigned long addr = ap->ioaddr.bmdma_addr + ATA_DMA_STATUS;
+		outb(inb(addr), addr);
+	}
+}
+
+
+/**
+ *	ata_bmdma_status - Read PCI IDE BMDMA status
+ *	@ap: Port associated with this ATA transaction.
+ *
+ *	Read and return BMDMA status register.
+ *
+ *	May be used as the bmdma_status() entry in ata_port_operations.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ */
+
+u8 ata_bmdma_status(struct ata_port *ap)
+{
+	u8 host_stat;
+	if (ap->flags & ATA_FLAG_MMIO) {
+		void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+		host_stat = readb(mmio + ATA_DMA_STATUS);
+	} else
+		host_stat = inb(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+	return host_stat;
+}
+
+
+/**
+ *	ata_bmdma_stop - Stop PCI IDE BMDMA transfer
+ *	@qc: Command we are ending DMA for
+ *
+ *	Clears the ATA_DMA_START flag in the dma control register
+ *
+ *	May be used as the bmdma_stop() entry in ata_port_operations.
+ *
+ *	LOCKING:
+ *	spin_lock_irqsave(host_set lock)
+ */
+
+void ata_bmdma_stop(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	if (ap->flags & ATA_FLAG_MMIO) {
+		void __iomem *mmio = (void __iomem *) ap->ioaddr.bmdma_addr;
+
+		/* clear start/stop bit */
+		writeb(readb(mmio + ATA_DMA_CMD) & ~ATA_DMA_START,
+			mmio + ATA_DMA_CMD);
+	} else {
+		/* clear start/stop bit */
+		outb(inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD) & ~ATA_DMA_START,
+			ap->ioaddr.bmdma_addr + ATA_DMA_CMD);
+	}
+
+	/* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
+	ata_altstatus(ap);        /* dummy read */
+}
+
 #ifdef CONFIG_PCI
 static struct ata_probe_ent *
 ata_probe_ent_alloc(struct device *dev, const struct ata_port_info *port)
drivers/scsi/libata-core.c +0 -234

240 lines not on this page · raw message

drivers/scsi/sata_nv.c +62 -119

246 lines not on this page · raw message

drivers/scsi/sata_sil24.c +10 -13
index 5d01e5c..3efebea 100644
@@ -842,9 +842,10 @@ static void sil24_port_stop(struct ata_p
 static void sil24_host_stop(struct ata_host_set *host_set)
 {
 	struct sil24_host_priv *hpriv = host_set->private_data;
+	struct pci_dev *pdev = to_pci_dev(host_set->dev);
 
-	iounmap(hpriv->host_base);
-	iounmap(hpriv->port_base);
+	pci_iounmap(pdev, hpriv->host_base);
+	pci_iounmap(pdev, hpriv->port_base);
 	kfree(hpriv);
 }
 
@@ -871,26 +872,23 @@ static int sil24_init_one(struct pci_dev
 		goto out_disable;
 
 	rc = -ENOMEM;
-	/* ioremap mmio registers */
-	host_base = ioremap(pci_resource_start(pdev, 0),
-			    pci_resource_len(pdev, 0));
+	/* map mmio registers */
+	host_base = pci_iomap(pdev, 0, 0);
 	if (!host_base)
 		goto out_free;
-	port_base = ioremap(pci_resource_start(pdev, 2),
-			    pci_resource_len(pdev, 2));
+	port_base = pci_iomap(pdev, 2, 0);
 	if (!port_base)
 		goto out_free;
 
 	/* allocate & init probe_ent and hpriv */
-	probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
+	probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL);
 	if (!probe_ent)
 		goto out_free;
 
-	hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL);
+	hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL);
 	if (!hpriv)
 		goto out_free;
 
-	memset(probe_ent, 0, sizeof(*probe_ent));
 	probe_ent->dev = pci_dev_to_dev(pdev);
 	INIT_LIST_HEAD(&probe_ent->node);
 
@@ -907,7 +905,6 @@ static int sil24_init_one(struct pci_dev
 	probe_ent->mmio_base = port_base;
 	probe_ent->private_data = hpriv;
 
-	memset(hpriv, 0, sizeof(*hpriv));
 	hpriv->host_base = host_base;
 	hpriv->port_base = port_base;
 
@@ -1011,9 +1008,9 @@ static int sil24_init_one(struct pci_dev
 
  out_free:
 	if (host_base)
-		iounmap(host_base);
+		pci_iounmap(pdev, host_base);
 	if (port_base)
-		iounmap(port_base);
+		pci_iounmap(pdev, port_base);
 	kfree(probe_ent);
 	kfree(hpriv);
 	pci_release_regions(pdev);
drivers/scsi/sata_uli.c +27 -10
index 8f50257..7ac5a5f 100644
@@ -44,6 +44,8 @@ enum {
 	uli_5287		= 1,
 	uli_5281		= 2,
 
+	uli_max_ports		= 4,
+
 	/* PCI configuration registers */
 	ULI5287_BASE		= 0x90, /* sata0 phy SCR registers */
 	ULI5287_OFFS		= 0x10, /* offset from sata0->sata1 phy regs */
@@ -51,6 +53,10 @@ enum {
 	ULI5281_OFFS		= 0x60, /* offset from sata0->sata1 phy regs */
 };
 
+struct uli_priv {
+	unsigned int		scr_cfg_addr[uli_max_ports];
+};
+
 static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
 static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg);
 static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
@@ -137,7 +143,8 @@ MODULE_VERSION(DRV_VERSION);
 
 static unsigned int get_scr_cfg_addr(struct ata_port *ap, unsigned int sc_reg)
 {
-	return ap->ioaddr.scr_addr + (4 * sc_reg);
+	struct uli_priv *hpriv = ap->host_set->private_data;
+	return hpriv->scr_cfg_addr[ap->port_no] + (4 * sc_reg);
 }
 
 static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
@@ -182,6 +189,7 @@ static int uli_init_one (struct pci_dev 
 	int rc;
 	unsigned int board_idx = (unsigned int) ent->driver_data;
 	int pci_dev_busy = 0;
+	struct uli_priv *hpriv;
 
 	if (!printed_version++)
 		dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n");
@@ -210,10 +218,18 @@ static int uli_init_one (struct pci_dev 
 		goto err_out_regions;
 	}
 
+	hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL);
+	if (!hpriv) {
+		rc = -ENOMEM;
+		goto err_out_probe_ent;
+	}
+
+	probe_ent->private_data = hpriv;
+
 	switch (board_idx) {
 	case uli_5287:
-		probe_ent->port[0].scr_addr = ULI5287_BASE;
-		probe_ent->port[1].scr_addr = ULI5287_BASE + ULI5287_OFFS;
+		hpriv->scr_cfg_addr[0] = ULI5287_BASE;
+		hpriv->scr_cfg_addr[1] = ULI5287_BASE + ULI5287_OFFS;
        		probe_ent->n_ports = 4;
 
        		probe_ent->port[2].cmd_addr = pci_resource_start(pdev, 0) + 8;
@@ -221,27 +237,27 @@ static int uli_init_one (struct pci_dev 
 		probe_ent->port[2].ctl_addr =
 			(pci_resource_start(pdev, 1) | ATA_PCI_CTL_OFS) + 4;
 		probe_ent->port[2].bmdma_addr = pci_resource_start(pdev, 4) + 16;
-		probe_ent->port[2].scr_addr = ULI5287_BASE + ULI5287_OFFS*4;
+		hpriv->scr_cfg_addr[2] = ULI5287_BASE + ULI5287_OFFS*4;
 
 		probe_ent->port[3].cmd_addr = pci_resource_start(pdev, 2) + 8;
 		probe_ent->port[3].altstatus_addr =
 		probe_ent->port[3].ctl_addr =
 			(pci_resource_start(pdev, 3) | ATA_PCI_CTL_OFS) + 4;
 		probe_ent->port[3].bmdma_addr = pci_resource_start(pdev, 4) + 24;
-		probe_ent->port[3].scr_addr = ULI5287_BASE + ULI5287_OFFS*5;
+		hpriv->scr_cfg_addr[3] = ULI5287_BASE + ULI5287_OFFS*5;
 
 		ata_std_ports(&probe_ent->port[2]);
 		ata_std_ports(&probe_ent->port[3]);
 		break;
 
 	case uli_5289:
-		probe_ent->port[0].scr_addr = ULI5287_BASE;
-		probe_ent->port[1].scr_addr = ULI5287_BASE + ULI5287_OFFS;
+		hpriv->scr_cfg_addr[0] = ULI5287_BASE;
+		hpriv->scr_cfg_addr[1] = ULI5287_BASE + ULI5287_OFFS;
 		break;
 
 	case uli_5281:
-		probe_ent->port[0].scr_addr = ULI5281_BASE;
-		probe_ent->port[1].scr_addr = ULI5281_BASE + ULI5281_OFFS;
+		hpriv->scr_cfg_addr[0] = ULI5281_BASE;
+		hpriv->scr_cfg_addr[1] = ULI5281_BASE + ULI5281_OFFS;
 		break;
 
 	default:
@@ -258,9 +274,10 @@ static int uli_init_one (struct pci_dev 
 
 	return 0;
 
+err_out_probe_ent:
+	kfree(probe_ent);
 err_out_regions:
 	pci_release_regions(pdev);
-
 err_out:
 	if (!pci_dev_busy)
 		pci_disable_device(pdev);