libata: cosmetic change in ata_bus_softreset()
PATCH 1/1 libata: cosmetic change in ata_bus_softreset()
ata_bus_softreset() should return AC_ERR_* on failure not arbitrary positive number. While at it, kill trailing indentations and reformat comment.
drivers/scsi/libata-core.c +5 -6
@@ -1999,13 +1999,12 @@ static unsigned int ata_bus_softreset(st*/ msleep (150 ); - -/* Before we perform post reset processing we want to see if -the bus shows 0xFF because the odd clown forgets the D7 pulldown -resistor */ - +/* Before we perform post reset processing we want to see if +* the bus shows 0xFF because the odd clown forgets the D7 +* pulldown resistor +*/ if (ata_check_status (ap) ==0xFF ) -return 1 ;/* Positive is failure for some reason */ +return AC_ERR_OTHER ;ata_bus_post_reset (ap, devmask);
Quoted 16 lines · Tejun Heo
ata_bus_softreset()should return AC_ERR_* on failure not arbitrary positive number. While at it, kill trailing indentations and reformat comment.Signed-off-by Tejun Heo <[email protected]>drivers/scsi/libata-core.c +0
-2@@ -1999,13 +1999,12 @@ static unsigned int ata_bus_softreset(st*/ msleep (150 ); - -/* Before we perform post reset processing we want to see if
drivers/scsi/libata-core.c static unsigned int ata_bus_softreset(st · line 2007
Quoted 10 lines
drivers/scsi/libata-core.c +5
-4-the bus shows 0xFF because the odd clown forgets the D7 pulldown -resistor */ - +/* Before we perform post reset processing we want to see if +* the bus shows 0xFF because the odd clown forgets the D7 +* pulldown resistor +*/ if (ata_check_status (ap) ==0xFF ) -return 1 ;/* Positive is failure for some reason */ +return AC_ERR_OTHER ;
agreed and will apply, though note:
The reason Alan did this is most likely because the only other function that produces a non-zero return code is ata_bus_edd->ata_busy_sleep, which returns 1.
Though really, we should rip out E.D.D. anyway....
Jeff
PATCH 1/1 libata: cosmetic changes in ata_bus_softreset()
ata_bus_softreset() should return AC_ERR_* on failure not arbitrary positive number. While at it, reformat comment above it.
---
libata-core.c | 11 +++++------ 1 file changed, 5 insertions(+), 6 deletions(-)
drivers/scsi/libata-core.c +5 -6
@@ -1999,13 +1999,12 @@ static unsigned int ata_bus_softreset(st*/ msleep (150 ); - -/* Before we perform post reset processing we want to see if -the bus shows 0xFF because the odd clown forgets the D7 pulldown -resistor */ - +/* Before we perform post reset processing we want to see if +* the bus shows 0xFF because the odd clown forgets the D7 +* pulldown resistor +*/ if (ata_check_status (ap) ==0xFF ) -return 1 ;/* Positive is failure for some reason */ +return AC_ERR_OTHER ;ata_bus_post_reset (ap, devmask);
Re: [PATCH] libata: cosmetic changes in ata_bus_softreset()
Quoted 5 lines · Tejun Heo
ata_bus_softreset()should return AC_ERR_* on failure not arbitrary positive number. While at it, reformat comment above it.Signed-off-by Tejun Heo <[email protected]>Acked-by Alan Cox <[email protected]>
ACK but doesn't apply to #upstream (now linux-2.6.git as well)
PATCH 1/1 libata: cosmetic changes in ata_bus_softreset()
ata_bus_softreset() should return AC_ERR_* on failure not arbitrary positive number. While at it, reformat comment above it.
---
Hmmm... weird. Here's the regenerated patch against the current upstream (aec5c3c1a929d7d79a420e943285cf3ba26a7c0d).
libata-core.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-)
drivers/scsi/libata-core.c +4 -5
@@ -2008,13 +2008,12 @@ static unsigned int ata_bus_softreset(st*/ msleep (150 ); -/* Before we perform post reset processing we want to see if -the bus shows 0xFF because the odd clown forgets the D7 pulldown -resistor */ - +* the bus shows 0xFF because the odd clown forgets the D7 +* pulldown resistor. +*/ if (ata_check_status (ap) ==0xFF ) -return 1 ;/* Positive is failure for some reason */ +return AC_ERR_OTHER ;ata_bus_post_reset (ap, devmask);
Jeff Garzik
AppliedRe: [PATCH] libata: cosmetic changes in ata_bus_softreset()
Quoted 5 lines · Tejun Heo
ata_bus_softreset()should return AC_ERR_* on failure not arbitrary positive number. While at it, reformat comment above it.Signed-off-by Tejun Heo <[email protected]>Acked-by Alan Cox <[email protected]>
applied
PATCH 1/1 libata: kill E.D.D.
In reply to Jeff GarzikE.D.D. has no user in-tree and mostly useless. Kill it. For possible out-of-tree users, add a nice warning message and error handling if LLDD doesn't report any useable reset mechanism (and thus tries to use E.D.D.).
---
I left BUS_EDD constant alone as I have no idea know how those BUS_* constants are used. Tested on sata_sil, sata_promise, ata_piix and ahci.
drivers/scsi/libata-core.c | 98 +++++---------------------------------------- include/linux/libata.h | 1 2 files changed, 13 insertions(+), 86 deletions(-)
drivers/scsi/libata-core.c +13 -85
@@ -1081,9 +1081,8 @@ unsigned int ata_pio_need_iordy(const st* * Read ID data from the specified device. ATA_CMD_ID_ATA is * performed on ATA devices and ATA_CMD_ID_ATAPI on ATAPI -* devices. This function also takes care of EDD signature -* misreporting (to be removed once EDD support is gone) and -* issues ATA_CMD_INIT_DEV_PARAMS for pre-ATA4 drives. +* devices. This function also issues ATA_CMD_INIT_DEV_PARAMS +* for pre-ATA4 drives. * * LOCKING: * Kernel thread context (may sleep)
@@ -1095,7 +1094,6 @@ static int ata_dev_read_id(struct ata_po unsigned int *p_class, int post_reset, u16 **p_id) { unsigned int class = *p_class; -unsigned int using_edd;struct ata_taskfile tf;unsigned int err_mask =0 ;u16 *id;
@@ -1104,12 +1102,6 @@ static int ata_dev_read_id(struct ata_poDPRINTK ("ENTER, host %u, dev %u\n" , ap->id, dev->devno); -if (ap->ops->probe_reset || - ap->flags & (ATA_FLAG_SRST |ATA_FLAG_SATA_RESET )) - using_edd =0 ; -else - using_edd =1 ; -ata_dev_select (ap, dev->devno,1 ,1 );/* select device 0/1 */ id =kmalloc (sizeof (id[0 ]) *ATA_ID_WORDS ,GFP_KERNEL );
@@ -1139,32 +1131,9 @@ static int ata_dev_read_id(struct ata_po err_mask =ata_exec_internal (ap, dev, &tf,DMA_FROM_DEVICE , id,sizeof (id[0 ]) *ATA_ID_WORDS ); -if (err_mask) { rc = -EIO ; reason ="I/O error" ; - -if (err_mask & ~AC_ERR_DEV ) - goto err_out; - -/* -* arg! EDD works for all test cases, but seems to return -* the ATA signature for some ATAPI devices. Until the -* reason for this is found and fixed, we fix up the mess -* here. If IDENTIFY DEVICE returns command aborted -* (as ATAPI devices do), then we issue an -* IDENTIFY PACKET DEVICE. -* -* ATA software reset (SRST, the default) does not appear -* to have this problem. -*/ -if ((using_edd) && (class ==ATA_DEV_ATA )) { -u8 err = tf.feature; -if (err &ATA_ABORTED ) { - class =ATA_DEV_ATAPI ; - goto retry; - } - } goto err_out; }
@@ -2005,45 +1974,6 @@ static void ata_bus_post_reset(struct at ap->ops->dev_select (ap,0 ); } -/** -* ata_bus_edd - Issue EXECUTE DEVICE DIAGNOSTIC command. -* @ap: Port to reset and probe -* -* Use the EXECUTE DEVICE DIAGNOSTIC command to reset and -* probe the bus. Not often used these days. -* -* LOCKING: -* PCI/etc. bus probe sem. -* Obtains host_set lock. -* -*/ - -static unsigned int ata_bus_edd (struct ata_port *ap) -{ -struct ata_taskfile tf; -unsigned long flags; - -/* set up execute-device-diag (bus reset) taskfile */ -/* also, take interrupts to a known state (disabled) */ -DPRINTK ("execute-device-diag\n" ); -ata_tf_init (ap, &tf,0 ); - tf.ctl |=ATA_NIEN ; - tf.command =ATA_CMD_EDD ; - tf.protocol =ATA_PROT_NODATA ; - -/* do bus reset */ -spin_lock_irqsave (&ap->host_set->lock, flags); -ata_tf_to_host (ap, &tf); -spin_unlock_irqrestore (&ap->host_set->lock, flags); - -/* spec says at least 2ms. but who knows with those -* crazy ATAPI devices... -*/ -msleep (150 ); - -return ata_busy_sleep (ap,ATA_TMOUT_BOOT_QUICK ,ATA_TMOUT_BOOT ); -} -static unsigned int ata_bus_softreset (struct ata_port *ap,unsigned int devmask) {
@@ -2115,7 +2045,7 @@ void ata_bus_reset(struct ata_port *ap)struct ata_ioports *ioaddr = &ap->ioaddr;unsigned int slave_possible = ap->flags &ATA_FLAG_SLAVE_POSS ;u8 err; -unsigned int dev0, dev1 =0 , rc =0 , devmask =0 ; +unsigned int dev0, dev1 =0 , devmask =0 ;DPRINTK ("ENTER, host %u, port %u\n" , ap->id, ap->port_no);
@@ -2138,18 +2068,8 @@ void ata_bus_reset(struct ata_port *ap)/* issue bus reset */ if (ap->flags &ATA_FLAG_SRST ) - rc =ata_bus_softreset (ap, devmask); -else if ((ap->flags &ATA_FLAG_SATA_RESET ) ==0 ) { -/* set up device control */ -if (ap->flags &ATA_FLAG_MMIO ) -writeb (ap->ctl, (void __iomem *) ioaddr->ctl_addr); -else -outb (ap->ctl, ioaddr->ctl_addr); - rc =ata_bus_edd (ap); - } - -if (rc) - goto err_out; +if (ata_bus_softreset (ap, devmask)) + goto err_out;/* * determine by signature whether we have ATA or ATAPI devices
@@ -4535,6 +4455,14 @@ static struct ata_port * ata_host_add(coint rc;DPRINTK ("ENTER\n" ); + +if (!ent->port_ops->probe_reset && + !(ent->host_flags & (ATA_FLAG_SATA_RESET |ATA_FLAG_SRST ))) { +printk (KERN_ERR "ata%u: no reset mechanism available\n" , + port_no); +return NULL ; + } + host =scsi_host_alloc (ent->sht,sizeof (struct ata_port ));if (!host)return NULL ;
include/linux/libata.h +0 -1
@@ -161,7 +161,6 @@ enum {ATA_QCFLAG_EH_SCHEDULED = (1 <<5 ),/* EH scheduled */ /* various lengths of time */ -ATA_TMOUT_EDD =5 *HZ ,/* heuristic */ ATA_TMOUT_PIO =30 *HZ ,ATA_TMOUT_BOOT =30 *HZ ,/* heuristic */ ATA_TMOUT_BOOT_QUICK = 7 * HZ, /* heuristic */
Jeff Garzik
AppliedRe: [PATCH] libata: kill E.D.D.
Quoted 6 lines · Tejun Heo
E.D.D. has no user in-tree and mostly useless. Kill it. For possible out-of-tree users, add a nice warning message and error handling if LLDD doesn't report any useable reset mechanism (and thus tries to use E.D.D.).
Signed-off-by Tejun Heo <[email protected]>
applied
Re: [PATCH] libata: kill E.D.D.
In reply to Tejun HeoQuoted 4 lines · Tejun Heo
E.D.D. has no user in-tree and mostly useless. Kill it. For possible out-of-tree users, add a nice warning message and error handling if LLDD doesn't report any useable reset mechanism (and thus tries to use E.D.D.).
We made need this for some ISAPnP, M68K and embedded devices but its easy enough to put back when actual hardware is found.
Quoted 5 lines · Tejun Heo
ata_bus_softreset()should return AC_ERR_* on failure not arbitrary positive number. While at it, kill trailing indentations and reformat comment.Signed-off-by Tejun Heo <[email protected]>
Please pull #upstream, make sure you have2e9edbf815e42f93dd29a9981f27bd421acc47df, and then resend. I ran chomp (attached) on a bunch of files.
Jeff