Status of NCQ in libata
Hello,
I'd like to know about the current status of NCQ support in libata, whether anyone is actively working on it, where I should find a development branch (there's no ncq branch anymore in libata-dev.git it seems) and when an upstream merge should be expected.
Thanks.
Signature · 2 lines
Dan Aloni [email protected], [email protected], [email protected], [email protected]
Quoted 6 lines · Dan Aloni
Hello,
I'd like to know about the current status of NCQ support in libata, whether anyone is actively working on it, where I should find a development branch (there's no ncq branch anymore in libata-dev.git it seems) and when an upstream merge should be expected.
You can give it a spin in the 'ncq' branch in the block layer git repo:
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux-2.6-block.git
Only one real bit needs to get merged in libata for ncq to be submitted, and that is Tejun's eh rework. Once that is in, ncq becomes a fairly small patch and can probably go straight in.
AHCI is still the only supported controller, once NCQ is merged I'm sure a few others will follow.
Signature · 1 line
Jens Axboe
Quoted 9 lines · Jens Axboe
Quoted 5 lines · Dan Aloni
Hello,
I'd like to know about the current status of NCQ support in libata,
whether anyone is actively working on it, where I should find a development branch (there's no ncq branch anymore in libata-dev.git it seems) and when an upstream merge should be expected.You can give it a spin in the 'ncq' branch in the block layer git repo:
Quoted 9 lines
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux-2.6-block.gitOnly one real bit needs to get merged in libata for ncq to be submitted, and that is Tejun's eh rework. Once that is in, ncq becomes a fairly small patch and can probably go straight in.
AHCI is still the only supported controller, once NCQ is merged I'm sure a few others will follow.
Patches going out later today. :) I've just ported the NCQ stuff over it and about to test it. As I have the doc and hardware NCQ support for sata_sil24 will soon follow.
Signature · 1 line
tejun
Quoted 17 lines · Tejun Heo
Quoted 16 lines · Jens Axboe
Quoted 6 lines · Dan Aloni
Hello,
I'd like to know about the current status of NCQ support in libata, whether anyone is actively working on it, where I should find a development branch (there's no ncq branch anymore in libata-dev.git it seems) and when an upstream merge should be expected.
You can give it a spin in the 'ncq' branch in the block layer git repo:
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux-2.6-block.gitOnly one real bit needs to get merged in libata for ncq to be submitted, and that is Tejun's eh rework. Once that is in, ncq becomes a fairly small patch and can probably go straight in.
Quoted 7 lines
Quoted 3 lines
AHCI is still the only supported controller, once NCQ is merged I'm sure a few others will follow.
Patches going out later today. :) I've just ported the NCQ stuff over it and about to test it. As I have the doc and hardware NCQ support for
sata_sil24will soon follow.
Wonderful! I'm pretty confident in the NCQ stuff these days, so if Jeff is up for it, it could make 2.6.17.
Signature · 1 line
Jens Axboe
Quoted 17 lines · Tejun Heo
Quoted 16 lines · Jens Axboe
Quoted 6 lines · Dan Aloni
Hello,
I'd like to know about the current status of NCQ support in libata, whether anyone is actively working on it, where I should find a development branch (there's no ncq branch anymore in libata-dev.git it seems) and when an upstream merge should be expected.
You can give it a spin in the 'ncq' branch in the block layer git repo:
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux-2.6-block.gitOnly one real bit needs to get merged in libata for ncq to be submitted, and that is Tejun's eh rework. Once that is in, ncq becomes a fairly small patch and can probably go straight in.
Quoted 7 lines
Quoted 3 lines
AHCI is still the only supported controller, once NCQ is merged I'm sure a few others will follow.
Patches going out later today. :) I've just ported the NCQ stuff over it and about to test it. As I have the doc and hardware NCQ support for
sata_sil24will soon follow.
Good to see it's going well. I'm considering to implement NCQ/TCQ for sata_mv (I have the necessary resources for it), so I'm hoping that I'd be able to base my efforts on the current ncq branch without worrying too much about interface changes.
Signature · 2 lines
Dan Aloni [email protected], [email protected], [email protected], [email protected]
Quoted 22 lines · Dan Aloni
Quoted 21 lines · Tejun Heo
Quoted 19 lines · Jens Axboe
Quoted 6 lines · Dan Aloni
Hello,
I'd like to know about the current status of NCQ support in libata, whether anyone is actively working on it, where I should find a development branch (there's no ncq branch anymore in libata-dev.git it seems) and when an upstream merge should be expected.
You can give it a spin in the 'ncq' branch in the block layer git repo:
git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux-2.6-block.gitOnly one real bit needs to get merged in libata for ncq to be submitted, and that is Tejun's eh rework. Once that is in, ncq becomes a fairly small patch and can probably go straight in.
AHCI is still the only supported controller, once NCQ is merged I'm sure a few others will follow.
Quoted 8 lines
Quoted 3 lines
Patches going out later today. :) I've just ported the NCQ stuff over it and about to test it. As I have the doc and hardware NCQ support for
sata_sil24will soon follow.Good to see it's going well. I'm considering to implement NCQ/TCQ for
sata_mv(I have the necessary resources for it), so I'm hoping that I'd be able to base my efforts on the current ncq branch without worrying too much about interface changes.
As seen from the low level sata driver, there isn't much interface to change. Basically you just want to signal a higher queueing depth, which will enable the SCSI layer to queue a higher number of ios at any time. The rest is up to you, how you actually talk to the hardware. Then there's error handling, I don't think much will change there after Tejuns merge either.
So if you started off the 'ncq' branch in the block repo, you should be able to pretty much cary your sata_mv changes straight over. Any change needed would be to accomodate other libata changes, not ncq.
Signature · 1 line
Jens Axboe