Remove CONFIG_PARPORT_ARC, drivers/parport/parport_arc.c
RFC PATCH 1/1 Remove CONFIG_PARPORT_ARC, drivers/parport/parport_arc.c
From: Domen Puncer <[email protected]>
It's wasn't referenced in Makefile since at least 2.2.8, unbuildable due to trivial typos and things like DATA_LATCH and arc_write_control() which doesn't exist.
Adrian Bunk:
adapted the patch to unrelated context changes
Signed-off-by Domen Puncer <[email protected]>
Signed-off-by Alexey Dobriyan <[email protected]>
Signed-off-by Adrian Bunk <[email protected]>
---
drivers/parport/Kconfig | 5 - drivers/parport/parport_arc.c | 139 ---------------------------------- 2 files changed, 144 deletions(-)
drivers/parport/parport_arc.c +0 -139
@@ -1,139 +0,0 @@ -/* Low-level parallel port routines for Archimedes onboard hardware -* -* Author: Phil Blundell <[email protected]> -*/ - -/* This driver is for the parallel port hardware found on Acorn's old -* range of Archimedes machines. The A5000 and newer systems have PC-style -* I/O hardware and should use the parport_pc driver instead. -* -* The Acorn printer port hardware is very simple. There is a single 8-bit -* write-only latch for the data port and control/status bits are handled -* with various auxilliary input and output lines. The port is not -* bidirectional, does not support any modes other than SPP, and has only -* a subset of the standard printer control lines connected. -*/ - -#include <linux/threads.h> -#include <linux/delay.h> -#include <linux/errno.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/kernel.h> -#include <linux/slab.h> -#include <linux/parport.h> - -#include <asm/ptrace.h> -#include <asm/io.h> -#include <asm/arch/oldlatches.h> -#include <asm/arch/irqs.h> - -#define DATA_ADDRESS 0x3350010 - -/* This is equivalent to the above and only used for request_region. */ -#define PORT_BASE 0x80000000 | ((DATA_ADDRESS - IO_BASE) >> 2) - -/* The hardware can't read from the data latch, so we must use a soft -copy. */ -static unsigned char data_copy; - -/* These are pretty simple. We know the irq is never shared and the -kernel does all the magic that's required. */ -static void arc_enable_irq (struct parport *p) -{ -enable_irq (p->irq); -} - -static void arc_disable_irq (struct parport *p) -{ -disable_irq (p->irq); -} - -static void arc_interrupt (int irq,void *dev_id,struct pt_regs *regs) -{ -parport_generic_irq (irq, (struct parport *) dev_id, regs); -} - -static void arc_write_data (struct parport *p,unsigned char data) -{ - data_copy = data; -outb_t (data,DATA_LATCH ); -} - -static unsigned char arc_read_data (struct parport *p) -{ -return data_copy; -} - -static struct parport_operations parport_arc_ops = -{ - .write_data = arc_write_data, - .read_data = arc_read_data, - - .write_control = arc_write_control, - .read_control = arc_read_control, - .frob_control = arc_frob_control, - - .read_status = arc_read_status, - - .enable_irq = arc_enable_irq, - .disable_irq = arc_disable_irq, - - .data_forward = arc_data_forward, - .data_reverse = arc_data_reverse, - - .init_state = arc_init_state, - .save_state = arc_save_state, - .restore_state = arc_restore_state, - - .epp_write_data = parport_ieee1284_epp_write_data, - .epp_read_data = parport_ieee1284_epp_read_data, - .epp_write_addr = parport_ieee1284_epp_write_addr, - .epp_read_addr = parport_ieee1284_epp_read_addr, - - .ecp_write_data = parport_ieee1284_ecp_write_data, - .ecp_read_data = parport_ieee1284_ecp_read_data, - .ecp_write_addr = parport_ieee1284_ecp_write_addr, - - .compat_write_data = parport_ieee1284_write_compat, - .nibble_read_data = parport_ieee1284_read_nibble, - .byte_read_data = parport_ieee1284_read_byte, - - .owner =THIS_MODULE , -}; - -/* --- Initialisation code -------------------------------- */ - -static int parport_arc_init (void ) -{ -/* Archimedes hardware provides only one port, at a fixed address */ -struct parport *p; -struct resource res; - char *fake_name = "parport probe"); - - res =request_region (PORT_BASE ,1 , fake_name); -if (res ==NULL ) -return 0 ; - - p =parport_register_port (PORT_BASE ,IRQ_PRINTERACK , -PARPORT_DMA_NONE , &parport_arc_ops); - -if (!p) { -release_region (PORT_BASE ,1 ); -return 0 ; - } - - p->modes =PARPORT_MODE_ARCSPP ; - p->size =1 ; -rename_region (res, p->name); - -printk (KERN_INFO "%s: Archimedes on-board port, using irq %d\n" , - p->irq); - -/* Tell the high-level drivers about the port. */ -parport_announce_port (p); - -return 1 ; -} - -module_init (parport_arc_init)
drivers/parport/Kconfig renamed from drivers/parport/Kconfig.old +0 -5
@@ -85,11 +85,6 @@ config PARPORT_NOT_PC bool -config PARPORT_ARC - tristate "Archimedes hardware" - depends on ARM && PARPORT - select PARPORT_NOT_PC - config PARPORT_IP32 tristate "SGI IP32 builtin port (EXPERIMENTAL)" depends on SGI_IP32 && PARPORT && EXPERIMENTAL