new pcmcia IDs for hostap - D-Link DCF-660W
Subsystems (3)
PATCH 3/5 new pcmcia IDs for hostap - D-Link DCF-660W
I use D-Link DCF-660W card with WPA protected network. By default orinoco_cs was loaded for my card so I was not able to connect. This patch make my card working with hostap_cs (like it was when I used pcmcia-cs). Card was used with hostap_cs during last year in two Zaurus models (2.4.18 on one and 2.6.11 - 2.6.16 on another).
I do not know does removing card from orinoco_cs is correct way.
Platform: Sharp Zaurus C760 running 2.6.16 and pcmciautils 013.
root@c7x0:~# pccardctl ident Socket 0: product info: "D-Link", "DCF-660W", "", "" manfid: 0xd601, 0x0005 function: 6 (network)
root@c7x0:~# iwconfig wlan0
wlan0 IEEE 802.11b ESSID:"test"
Mode:Master Frequency:2.422 GHz Access Point: 00:80:C8:2C:09:3F
Bit Rate:11 Mb/s Sensitivity=1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0drivers/net/wireless/hostap/hostap_cs.c +2 -0
@@ -974,6 +974,8 @@ 0x273fe3db, 0x32a1eaee),PCMCIA_DEVICE_PROD_ID12 ("Linksys" ,"Wireless CompactFlash Card" ,0x0733cc81 ,0x0c52f395 ), +PCMCIA_DEVICE_PROD_ID12 ("D-Link" ,"DCF-660W" , +0x1a424a1c ,0xe78b6dcc ), PCMCIA_DEVICE_NULL };MODULE_DEVICE_TABLE (pcmcia, hostap_cs_ids);
drivers/net/wireless/orinoco_cs.c +0 -1
@@ -539,7 +539,6 @@PCMCIA_DEVICE_MANF_CARD (0xc001 ,0x0008 ),/* CONTEC FLEXSCAN/FX-DDS110-PCC */ PCMCIA_DEVICE_MANF_CARD (0xc250 ,0x0002 ),/* Conceptronic CON11Cpro, EMTAC A2424i */ PCMCIA_DEVICE_MANF_CARD (0xd601 ,0x0002 ),/* Safeway 802.11b, ZCOMAX AirRunner/XI-300 */ -PCMCIA_DEVICE_MANF_CARD (0xd601 ,0x0005 ),/* D-Link DCF660, Sandisk Connect SDWCFB-000 */ PCMCIA_DEVICE_PROD_ID12 (" " ,"IEEE 802.11 Wireless LAN/PC Card" ,0x3b6e20c8 ,0xefccafe9 ),PCMCIA_DEVICE_PROD_ID12 ("3Com" ,"3CRWE737A AirConnect Wireless LAN PC Card" ,0x41240e5b ,0x56010af3 ), PCMCIA_DEVICE_PROD_ID12("ACTIONTEC", "PRISM Wireless LAN PC Card", 0x393089da, 0xa71e69d5),
Signature · 6 lines
JID: hrw-jabber.org Sharp Zaurus C-760 (OZ 3.5.x) OpenEmbedded/OpenZaurus/OPIE developer Fear leads to anger, anger leads to hate, hate... leads to suffering. -- Yoda
Updated to not touch orinoco_cs driver.
-----------------------------------------------------------------------
I use D-Link DCF-660W card with WPA protected network. By default orinoco_cs was loaded for my card so I was not able to connect. This patch make my card working with hostap_cs (like it was when I used pcmcia-cs). Card was used with hostap_cs during last year in two Zaurus models (2.4.18 on one and 2.6.11 - 2.6.16 on another).
I do not know does removing card from orinoco_cs is correct way.
Platform: Sharp Zaurus C760 running 2.6.16 and pcmciautils 013.
root@c7x0:~# pccardctl ident Socket 0: product info: "D-Link", "DCF-660W", "", "" manfid: 0xd601, 0x0005 function: 6 (network)
root@c7x0:~# iwconfig wlan0
wlan0 IEEE 802.11b ESSID:"test"
Mode:Master Frequency:2.422 GHz Access Point: 00:80:C8:2C:09:3F
Bit Rate:11 Mb/s Sensitivity=1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0drivers/net/wireless/hostap/hostap_cs.c +2 -0
@@ -974,6 +974,8 @@ 0x273fe3db, 0x32a1eaee),PCMCIA_DEVICE_PROD_ID12 ("Linksys" ,"Wireless CompactFlash Card" ,0x0733cc81 ,0x0c52f395 ), +PCMCIA_DEVICE_PROD_ID12 ("D-Link" ,"DCF-660W" , +0x1a424a1c ,0xe78b6dcc ), PCMCIA_DEVICE_NULL };MODULE_DEVICE_TABLE (pcmcia, hostap_cs_ids);
Signature · 7 lines
JID: hrw-jabber.org Palmtop: Sharp Zaurus C760 OpenEmbedded/OpenZaurus developer Woda, której dotykasz w rzekach, jest ostatkiem tej, która przeszła i początkiem tej, która przyjdzie: tak samo teraźniejszość. -- Leonardo da Vinci