Skip to contentSkip to conversation

Supplemental USB patch to previous 14 patches.

PATCH New Bryan O'Donoghue 3 participants 5 messages May 29, 2006 – May 31, 2006 Kbuild

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Supplemental USB patch to previous 14 patches.

Greetings list.
This is a supplemental patch to the 14 patches sent on the 26/05/06. It implements the various changes to the patch set that I had with Yuli Barcohen yesterday.

Let me know if further changes are required.

Best Regards,
Bryan

Signed-off-by Bryan O'Donoghue

This patchset is a supplemental to the previous submitted USB patches. The notable change here is that as a default VendorID/ProductID topology U-Boot is pretending to be Linux, which should be fine, since in U-Boot gserial and cdc_acm are protocol compatible with Linux and ostensibly we should be booting to Linux anyway, as was discussed on the mailing list recently.

modified: CHANGELOG
Update to the CHANGELOG.

modified: Makefile
Add AdderUSB to the top-level Makefile

modified: README
Ammend README to fix a typo and to give updated description of the functioning of the USB console as it is implemented currently in U-Boot

modified: drivers/usbdcore_mpc8xx.c
Fix a funny in this file that I noticed after submission to the list 0xFF000000 should say CFG_IMMR.

modified: drivers/usbtty.c
Slight change to the preceeding patch to switch to the new way to define Vendor/Product ids from either BoardName.h or to hook the default Linux ids.

modified: drivers/usbtty.h
Defines for the standard Linux Vendor/Product ids have been added to this header. gserial and cdc_acm are protocol compatible with the Linux version of the same, so this change should be fine.

modified: include/configs/Adder.h
Rolls back patch 06/14 from May 26th submission, in favour of include/configs/AdderUSB.h

new file: include/configs/AdderUSB.h
Simple wrapper header to facilitate a super-set of the Adder87x port, switching on the USB console.

---

 CHANGELOG                  |    5 +++-
 Makefile                   |    5 +++-
 README                     |   41 ++++++++++++++++++++++-------------
 drivers/usbdcore_mpc8xx.c  |    8 +++----
 drivers/usbtty.c           |   14 +++++++++---
 drivers/usbtty.h           |   14 ++++++++++++
 include/configs/Adder.h    |   17 ---------------
 include/configs/AdderUSB.h |   51 ++++++++++++++++++++++++++++++++++++++++++++
 8 files changed, 112 insertions(+), 43 deletions(-)
 create mode 100644 include/configs/AdderUSB.h

41469d4a6ea4030c262f5d0f363d9515543c415e

CHANGELOG +3 -2
@@ -10,8 +10,9 @@ Changes since U-Boot 1.1.4:
   - Minor changes to usbdcore_omap1510.c usbdcore_omap1510.h
   - Update usbcore slightly to ease host enumeration.
   - Fix non-portable endian problems in usbdcore and usbdcore_ep0.
-  - Switch on USB device as default in Adder_config
-  Patch by Bryan O'Donoghue <[email protected]>, 26 May 2006
+  - Add AdderUSB_config as a defconfig to enable usage of the USB console
+    by default with the Adder87x U-Boot port.
+  Patch by Bryan O'Donoghue <[email protected]>, 29 May 2006
 
 * Update Intel IXP4xx support
   - Add IXP4xx NPE ethernet MAC support
Makefile +4 -1
@@ -58,7 +58,7 @@ ifeq ($(HOSTARCH),ppc)
 CROSS_COMPILE =
 else
 ifeq ($(ARCH),ppc)
-CROSS_COMPILE = powerpc-linux-
+CROSS_COMPILE = ppc_8xx-
 endif
 ifeq ($(ARCH),arm)
 CROSS_COMPILE = arm-linux-
@@ -437,6 +437,9 @@ AdderII_config  \
 	@echo "#define CONFIG_MPC852T" > include/config.h)
 	@./mkconfig -a Adder ppc mpc8xx adder
 
+AdderUSB_config:	unconfig
+	@./mkconfig -a AdderUSB ppc mpc8xx adder
+
 ADS860_config     \
 FADS823_config    \
 FADS850SAR_config \
README +25 -16

59 lines not on this page · raw message

drivers/usbdcore_mpc8xx.c +4 -4
@@ -754,7 +754,7 @@ static void mpc8xx_udc_advance_rx(volati
 {
 	if((*rx_cbdp)->cbd_sc & RX_BD_W){
 		*rx_cbdp  = (volatile cbd_t*)
-			(endpoints[epid]->rbase +  0xFF000000);
+			(endpoints[epid]->rbase + CFG_IMMR);
 			
 	}else{
 		(*rx_cbdp)++;
@@ -782,7 +782,7 @@ static void mpc8xx_udc_flush_tx_fifo(int
 	usbp->uscom = 0x40 | 0;
 	
 	/* reset ring */
-	tx_cbdp = (cbd_t*)(endpoints[epid]->tbptr +  0xFF000000);
+	tx_cbdp = (cbd_t*)(endpoints[epid]->tbptr + CFG_IMMR);
 	tx_cbdp->cbd_sc = (TX_BD_I | TX_BD_W);
 
 		
@@ -887,7 +887,7 @@ static int mpc8xx_udc_ep_tx (struct usb_
 	}
 
 	ep = epi->endpoint_address & 0x03;
-	tx_cbdp = (cbd_t*)(endpoints[ep]->tbptr +  0xFF000000);
+	tx_cbdp = (cbd_t*)(endpoints[ep]->tbptr + CFG_IMMR);
 		
 	if(tx_cbdp->cbd_sc&TX_BD_R || usbp->usber&USB_E_TXB){
 		mpc8xx_udc_flush_tx_fifo(ep);
@@ -904,7 +904,7 @@ static int mpc8xx_udc_ep_tx (struct usb_
 			return -1;
 		}	
 
-		tx_cbdp = (cbd_t*)(endpoints[ep]->tbptr +  0xFF000000);
+		tx_cbdp = (cbd_t*)(endpoints[ep]->tbptr + CFG_IMMR);
 		while(tx_cbdp->cbd_sc&TX_BD_R){};
 		tx_cbdp->cbd_sc = (tx_cbdp->cbd_sc&TX_BD_W);
 	
drivers/usbtty.c +1 -0
@@ -30,15 +30,20 @@
 #include "usbtty.h"
 #include "usb_cdc_acm.h"
 #include "usbdescriptors.h"
+#include <config.h>		/* If defined, override Linux identifiers

with
+ * vendor specific ones */

#if 0
-#define TTYDBG(fmt,args...) serial_printf("[%s] %s %d: "fmt, __FILE__,__FUNCTION__,__LINE__,##args) +#define TTYDBG(fmt,args...)\
+ serial_printf("[%s] %s %d: "fmt, __FILE__,__FUNCTION__,__LINE__,##args)
#else
#define TTYDBG(fmt,args...) do{}while(0)
#endif

#if 1
-#define TTYERR(fmt,args...) serial_printf("ERROR![%s] %s %d: "fmt, __FILE__,__FUNCTION__,__LINE__,##args) +#define TTYERR(fmt,args...)\
+ serial_printf("ERROR![%s] %s %d: "fmt, __FILE__,__FUNCTION__,\
+ __LINE__,##args)
#else
#define TTYERR(fmt,args...) do{}while(0)
#endif
@@ -123,7 +128,6 @@ static struct usb_device_descriptor devi
.bDeviceProtocol = 0x00,
.bMaxPacketSize0 = EP0_MAX_PACKET_SIZE,
.idVendor = cpu_to_le16(CONFIG_USBD_VENDORID),
- .idProduct = cpu_to_le16(CONFIG_USBD_PRODUCTID),
.bcdDevice = cpu_to_le16(USBTTY_BCD_DEVICE),
.iManufacturer = STR_MANUFACTURER,
.iProduct = STR_PRODUCT,
@@ -742,6 +746,8 @@ static void usbtty_init_terminal_type(sh
/* Enumerate Device Descriptor */ device_descriptor.bDeviceClass =
COMMUNICATIONS_DEVICE_CLASS;
+ device_descriptor.idProduct =
+ cpu_to_le16(CONFIG_USBD_PRODUCTID_CDCACM);

/* Assign endpoint indices */ tx_endpoint = ACM_TX_ENDPOINT;
@@ -769,6 +775,8 @@ static void usbtty_init_terminal_type(sh

/* Enumerate Device Descriptor */ device_descriptor.bDeviceClass = 0xFF;
+ device_descriptor.idProduct =
+ cpu_to_le16(CONFIG_USBD_PRODUCTID_GSERIAL);

/* Assign endpoint indices */ tx_endpoint = GSERIAL_TX_ENDPOINT;

drivers/usbtty.h +14 -0
@@ -2,6 +2,9 @@
  * (C) Copyright 2003
  * Gerry Hamel, geh at ti.com, Texas Instruments
  *
+ * (C) Copyright 2006
+ * Bryan O'Donoghue, bodonoghue at codehermit.ie, CodeHermit
+ *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
@@ -28,6 +31,17 @@
 #include "usbdcore_omap1510.h"
 #endif
 
+#include <version_autogenerated.h>
+
+/* If no VendorID/ProductID is defined in config.h, pretend to be Linux 
+ * DO NOT Reuse this Vendor/Product setup with protocol incompatible devices */
+
+#define CONFIG_USBD_VENDORID 0x0525 	/* Linux/NetChip */
+#define CONFIG_USBD_PRODUCTID_GSERIAL 0xa4a6	/* gserial */
+#define CONFIG_USBD_PRODUCTID_CDCACM  0xa4a7	/* CDC ACM */
+#define CONFIG_USBD_MANUFACTURER "Das U-Boot"
+#define CONFIG_USBD_PRODUCT_NAME U_BOOT_VERSION
+
 
 #define CONFIG_USBD_CONFIGURATION_STR "TTY via USB"
 
include/configs/Adder.h +0 -14
@@ -5,9 +5,6 @@
  * Support for Analogue&Micro Adder boards family.
  * Tested on AdderII and Adder87x.
  *
- * Add USB console as default option.
- * Bryan O'Donoghue <[email protected]>
- * 
  * See file CREDITS for list of people who contributed to this
  * project.
  *
@@ -41,20 +38,6 @@
 #define CONFIG_ETHER_ON_FEC1
 #define CONFIG_ETHER_ON_FEC2
 
-#if 1
-#define CONFIG_USB_DEVICE		/* Include UDC driver */
-#define CONFIG_USB_TTY			/* Bind the TTY driver to UDC */
-#define CONFIG_USBD_MANUFACTURER	"CodeHermit.ie"
-#define CONFIG_USBD_PRODUCT_NAME	"Das U-Boot"
-/* Never use the next two defines in any production system */
-#define CONFIG_USBD_VENDORID		0xFFFF /* Some mythical vendor */
-#define CONFIG_USBD_PRODUCTID		0xFFFF /* Some mythical device */
-
-#define CFG_USB_EXTC_CLK 0x02		/* Oscillator on EXTC_CLK 2 */
-#define CFG_USB_BRG_CLK	0x04		/* or use Baud rate

generator 0x04 */ -#define CFG_CONSOLE_IS_IN_ENV
-#endif
-
#if defined(CONFIG_ETHER_ON_FEC1) || defined(CONFIG_ETHER_ON_FEC2) #define CFG_DISCOVER_PHY
#define FEC_ENET

include/configs/AdderUSB.h new file +35 -0
new file mode 100644
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2006 CodeHermit.
+ * Bryan O'Donoghue <[email protected]>
+ *
+ * Provides support for USB console on the Analogue & Micro Adder87x
+ * 
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ADDERUSB__
+#define __ADDERUSB__
+
+/* Include the board port */
+#include "Adder.h"
+
+#define CONFIG_USB_DEVICE		/* Include UDC driver */
+#define CONFIG_USB_TTY			/* Bind the TTY driver to UDC */
+#define CFG_USB_EXTC_CLK 0x02		/* Oscillator on EXTC_CLK 2 */
+#define CFG_USB_BRG_CLK	0x04		/* or use Baud rate

generator 0x04 */ +#define CFG_CONSOLE_IS_IN_ENV /* Console is
in env */ +
+/* If you have a USB-IF assigned VendorID then you may wish to define
+ * your own vendor specific values either in BoardName.h or directly in
+ * usbd_vendor_info.h
+ */
+
+/*
+#define CONFIG_USBD_MANUFACTURER "CodeHermit.ie"
+#define CONFIG_USBD_PRODUCT_NAME "Das U-Boot"
+#define CONFIG_USBD_VENDORID 0xFFFF
+#define CONFIG_USBD_PRODUCTID_GSERIAL 0xFFFF
+#define CONFIG_USBD_PRODUCTID_CDCACM 0xFFFE
+*/
+
+#endif /* __ADDERUSB_H__ */

#1 lore raw

PATCH 1/1 Supplemental USB patch to previous 14 patches.

Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

Bryan O'Donoghue writes:

Bryan> Greetings list. This is a supplemental patch to the 14 Bryan> patches sent on the 26/05/06. It implements the various Bryan> changes to the patch set that I had with Yuli Barcohen Bryan> yesterday.

I'm afraid it's not exactly what we discussed. Please see below.

Bryan> Let me know if further changes are required.

Bryan> diff --git a/Makefile b/Makefile Bryan> --- a/Makefile
Bryan> +++ b/Makefile
Bryan> @@ -58,7 +58,7 @@ ifeq ($(HOSTARCH),ppc) Bryan> CROSS_COMPILE = else ifeq ($(ARCH),ppc) Bryan> -CROSS_COMPILE = powerpc-linux- Bryan> +CROSS_COMPILE = ppc_8xx-

I don't think changing default compiler for ALL PowerPC targets was your intention.

Bryan> endif ifeq ($(ARCH),arm) CROSS_COMPILE = arm-linux- Bryan> @@ -437,6 +437,9 @@ AdderII_config \
Bryan> @echo "#define CONFIG_MPC852T" > include/config.h)
Bryan> @./mkconfig -a Adder ppc mpc8xx adder

Bryan> +AdderUSB_config: unconfig
Bryan> + @./mkconfig -a AdderUSB ppc mpc8xx adder Bryan> +

I didn't mean to add entirely new board target. I think a new target should be added to the existing Adder targets which would add a #define for USB console just like "#define CONFIG_MPC852T" is added for AdderII. Conditional on this #define, BoardName.h can include usbd_vendor.h which we decided to create. In the current version of your patch, it's exactly opposite: usbd_vendor.h (AdderUSB.h in our case) includes BoardName.h (Adder.h). This means that for every board wishing to support USB console you have to create another BoardNameUSB.h (which is a clone of AdderUSB.h). What's about creating CodeHermit.h containing something like this:

#define CONFIG_USB_DEVICE /* Include UDC driver */
#define CFG_USB_EXTC_CLK 0x02 /* Oscillator on EXTC_CLK 2 */
#define CFG_USB_BRG_CLK 0x04
#define CFG_CONSOLE_IS_IN_ENV
#define CONFIG_USBD_MANUFACTURER "CodeHermit.ie"
#define CONFIG_USBD_PRODUCT_NAME "Das U-Boot"
#define CONFIG_USBD_VENDORID 0xFFFF
#define CONFIG_USBD_PRODUCTID_GSERIAL 0xFFFF
#define CONFIG_USBD_PRODUCTID_CDCACM 0xFFFE

and adding to Adder.h

#ifdef CONFIG_USB_TTY
#include <CodeHermit.h>
#endif

"#define CONFIG_USB_TTY" would be added by the configuration target in the Makefile. Any other board can then include CodeHermit.h unchanged. To allow IDs overwriting, you can even use the following in CodeHermit.h:

#ifndef CONFIG_USBD_VENDORID
#define CONFIG_USBD_VENDORID 0xFFFF
#endif

and so on. Hopefully we can use Linux IDs (NetChip) instead of 0xFFFF as the defaults.

Signature · 4 lines
========================================================================
 Yuli Barcohen       | Phone +972-9-765-1788 |  Software Project Leader
 yuli at arabellasw.com | Fax   +972-9-765-7494 | Arabella Software, Israel
========================================================================
#2 lore raw

PATCH 1/1 Supplemental USB patch to previous 14 patches.

Quoted 3 lines · On Tue, 30 May 2006 21:09:11 +0300 Yuli Barcohen <[email protected]> wrote:

Bryan> -CROSS_COMPILE = powerpc-linux-
Bryan> +CROSS_COMPILE = ppc_8xx-

Blink. How the hell did that get in there ?

Quoted 4 lines

I didn't mean to add entirely new board target. I think a new target should be added to the existing Adder targets which would add a #define for USB console just like "#define CONFIG_MPC852T" is added for AdderII.

Actually I think that makes more sense then adding AdderUSB as the supplemental patch does. I concur, this is definitely the more generic/portable way to do this. I'll generate another supplemental patch in lieu of the previous patch, which implements the above.

Quoted 24 lines

Conditional on this #define, BoardName.h can include usbd_vendor.h which we decided to create. In the current version of your patch, it's exactly opposite: usbd_vendor.h (AdderUSB.h in our case) includes BoardName.h (Adder.h). This means that for every board wishing to support USB console you have to create another BoardNameUSB.h (which is a clone of AdderUSB.h). What's about creating CodeHermit.h containing something like this:

#define CONFIG_USB_DEVICE /* Include UDC driver */
#define CFG_USB_EXTC_CLK 0x02 /* Oscillator on EXTC_CLK 2 */
#define CFG_USB_BRG_CLK 0x04
#define CFG_CONSOLE_IS_IN_ENV
#define CONFIG_USBD_MANUFACTURER "CodeHermit.ie"
#define CONFIG_USBD_PRODUCT_NAME "Das U-Boot"
#define CONFIG_USBD_VENDORID 0xFFFF
#define CONFIG_USBD_PRODUCTID_GSERIAL 0xFFFF
#define CONFIG_USBD_PRODUCTID_CDCACM 0xFFFE

adding to Adder.h

#ifdef CONFIG_USB_TTY
#include <CodeHermit.h>
#endif

Quoted 8 lines

"#define CONFIG_USB_TTY" would be added by the configuration target in the Makefile. Any other board can then include CodeHermit.h unchanged. To allow IDs overwriting, you can even use the following in CodeHermit.h:

#ifndef CONFIG_USBD_VENDORID
#define CONFIG_USBD_VENDORID 0xFFFF
#endif

Right. I have a suggestion, which if it is agreeable to you and everybody else I will generate a new full supplemental patchset based upon.

1: For Adder ports, the Makefile shall be amended to optionally add CONFIG_USB_TTY to config.h as CONFIG_MPC852T is added by make AdderII_config. This will provisionally imply an appendation of USB to the config name. Hence three new values should be added to Makefile AdderUSB_config, Adder87xUSB_config and AdderIIUSB_config. - Do all these boards have USB facility ?

2: include/usbd_vendor.h shall be created. This will look almost exactly like the following.

#define CONFIG_USB_DEVICE /* Include UDC driver */
#define CFG_CONSOLE_IS_IN_ENV
/*
* Include your own Vendor specific defines here if you have been allocated a
* Vendor ID from the USB Implementors Forum. www.usb.org else DO NOT POLLUTE
* THE USB NAMESPACE !
*
* #define CONFIG_USBD_MANUFACTURER "CodeHermit.ie"
* #define CONFIG_USBD_PRODUCT_NAME "Das U-Boot"
* #define CONFIG_USBD_VENDORID 0xFFFF
* #define CONFIG_USBD_PRODUCTID_GSERIAL 0xFFFF
* #define CONFIG_USBD_PRODUCTID_CDCACM 0xFFFE
*/

If at a later date for argument sake, we were to implement RNDIS then the appropiate thing to do would be to add an optional CONFIG_USBD_PRODUCTID_RNDIS entry to usbd_vendor.h, with defaults for RNDIS values residing in usbrndis.h, thus maintaining the structure established with usbtty, thus far.

3: Adder.h shall be ammended with the following text in a rational place.

#ifdef CONFIG_USB_TTY
#include <usbd_vendor.h>

#define CFG_USB_EXTC_CLK 0x02 /* Oscillator on EXTC_CLK 2 */
#define CFG_USB_BRG_CLK 0x04 /* Or optionally on brgc4 */

#endif

I think CFG_USB_*BLAH* above shoudln't be in usbd_vendor.h for the case where the USB console is being compiled for a non 8xx port, say the omap1510/SX1 port, hence the two CFG options above should probably be board specific.

4:
usbtty.c shall stay pretty much the same.

usbtty.h - Shall be included in usbtty.c. CONFIG_USBD_VENDORID, CONFIG_USBD_PRODUCTID_GSERIAL will default to Linux values

config.h - Shall be included subsequent to usbtty.h, thus facilitating over-riding of default VENDORID/PRODUCTID values from Linux specific values to Vendor specific values.

I think that with this in place we pretty much do all that needs to be done. If everybody else is in agreement, I can have these changes made in <= 10 minutes.

Let me know what you think.

Best Regards,
Bryan

#3 lore raw

PATCH 1/1 Supplemental USB patch to previous 14 patches.

Quoted 7 lines · In message <[email protected]> you wrote:

1: For Adder ports, the Makefile shall be amended to optionally add CONFIG_USB_TTY to config.h as CONFIG_MPC852T is added by make AdderII_config. This will provisionally imply an appendation of USB to the config name. Hence three new values should be added to Makefile AdderUSB_config, Adder87xUSB_config and AdderIIUSB_config. - Do all these boards have USB facility ?

Please hold on for a minute. The  Makefile's  purpose  is  to  define
dependencies.   It  is  actually  not  the  place  to  put  code  and

configuration trickery there. Yes, I know, this is already in use with other boards, but I would like to ask you to use such features only when absolutely necessary.

If you just define a new make target name this is simple and readable (just a single word in the Makefile), and can be evaluated in the board config file instead.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Behind every great man, there is a woman -- urging him on.
	-- Harry Mudd, "I, Mudd", stardate 4513.3
#4 lore raw

PATCH 1/1 Supplemental USB patch to previous 14 patches.

On Wed, 31 May 2006 01:59:51 +0200
Wolfgang Denk <[email protected]> wrote:

Hello Wolfgang.

Quoted 5 lines
Please hold on for a minute. The  Makefile's  purpose  is  to  define
dependencies.   It  is  actually  not  the  place  to  put  code  and

configuration trickery there. Yes, I know, this is already in use with other boards, but I would like to ask you to use such features only when absolutely necessary.

OK I'll implement this whichever way is your preference.

I had made this addition to the Makefile as at last night's conversation

Adder_config \
Adder87x_config \
AdderII_config \
+AdderUSB_config \
+Adder87xUSB_config \
+AdderIIUSB_config \
: unconfig
$(if $(findstring AdderII,$@), \
@echo "#define CONFIG_MPC852T" > include/config.h)
+ $(if $(findstring USB,$@),\
+ @echo "#define CONFIG_USB_TTY" >> include/config.h)
@./mkconfig -a Adder ppc mpc8xx adder

with the following in Adder.h

/* USB TTY */
#ifdef CONFIG_USB_TTY

#include <usbd_vendor.h>                /* Include optional Vendor info */
#define CFG_USB_EXTC_CLK 0x02           /* Oscillator on EXTC_CLK 2 */
#define CFG_USB_BRG_CLK 0x04            /* or use Baud rate generator 0x04 */
#define CFG_CONSOLE_IS_IN_ENV           /* Console is in env */

#endif

Quoted 3 lines

If you just define a new make target name this is simple and readable (just a single word in the Makefile), and can be evaluated in the board config file instead.

Hmm, I don't really understand how this would work, i.e. if the conditional include CONFIG_USB_TTY or other *doesn't* go into config.h then how does Adder.h know whether or not to include the console code?

Bryan