rescue data after hd crash
hi all!
sorry if this is a double post, but i think the first post didn't succeed due to some registration race condition.
so here's my problem:
I have create a volume group with 4 250GByte harddisks with an ext3 file system on the 1TB result.
now the third harddisk failed and the volume group is "dead" - obviously.
lvscan tells me (like any other lv*, pv* command):
Couldn't find device with uuid 'A57CS6-SFlw-1ROR-uIvO-cX2o-OE2g-N3SVZN'. Couldn't find all physical volumes for volume group media_volgrp.
in my understanding many of the files should still be intact (those on the first two disks), and I would like to rescue these files.
i found no hints about such a crash recovery.
(checked http://www.tldp.org/HOWTO/LVM-HOWTO/)
my approach would be to "fake" the third disk, as see what the filesystem makes out of it.
any help is welcome.
thanks, chris
Quoted 2 lines · chris
I have create a volume group with 4 250GByte harddisks with an ext3 file system on the 1TB result.
Stripe or concat?
Quoted 1 line
now the third harddisk failed and the volume group is "dead" - obviously.
The way you created the volume had no redundancy - therefore 25% of your data is gone, as well as the volume's "completeness".
If you did a concat, then you (with playing) may be able to get some data back from the first 500GB of the volume - but I wouldn't want to rely on anything that came back from it. I'd suggest getting hold of 2 identical blank disks, and doing a binary (dd) copy of disks 1 and 2 to them - and then work on them. You might be able to use vgcfg{backup,restore} to tell the system that this volume is actually only on 2 disks.... However, anything that references data > 500GB into the volume is almost definitely lost - because although you've got 750G-1TB, it's almost all going to be linked back into the section that you've lost.
If you did a stripe, then you can forget getting any data back off it. You've lost every 4th block of whatever size you striped on. E.g. with a 64k stripe size, you'll have lost from 128k-192k, 384k-448k, etc. - and there's almost definitely going to be nothing salvagable from that.
Graham
vgchange -ay --partial
Quoted 29 lines · Graham Wood
Quoted 2 lines · chris
I have create a volume group with 4 250GByte harddisks with an ext3 file system on the 1TB result.
Stripe or concat?
Quoted 1 line
now the third harddisk failed and the volume group is "dead" - obviously.
The way you created the volume had no redundancy - therefore 25% of your data is gone, as well as the volume's "completeness".
If you did a concat, then you (with playing) may be able to get some data back from the first 500GB of the volume - but I wouldn't want to rely on anything that came back from it. I'd suggest getting hold of 2 identical blank disks, and doing a binary (dd) copy of disks 1 and 2 to them - and then work on them. You might be able to use vgcfg{backup,restore} to tell the system that this volume is actually only on 2 disks.... However, anything that references data > 500GB into the volume is almost definitely lost - because although you've got 750G-1TB, it's almost all going to be linked back into the section that you've lost.
If you did a stripe, then you can forget getting any data back off it. You've lost every 4th block of whatever size you striped on. E.g. with a 64k stripe size, you'll have lost from 128k-192k, 384k-448k, etc. - and there's almost definitely going to be nothing salvagable from that.
Graham
_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/
Signature · 15 lines
Regards,
Heinz -- The LVM Guy --
*** Software bugs are stupid.
Nevertheless it needs not so stupid people to solve them ***
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Heinz Mauelshagen Red Hat GmbH
Consulting Development Engineer Am Sonnenhang 11
Storage Development 56242 Marienrachdorf
Germany
[email protected] PHONE +49 171 7803392
FAX +49 2626 924446
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-Thanks Heinz,
this looks like what i was serching for. still, it didn't work out.
the first call of this command issued (apart from multiple "couln't find device..") "device-mapper ioctl cmd 9 failed: Das Argument ist ung�ltig"
(i hate german error messages, who invented this? it says "illegal
argument")
but also "1 logic voliume(s) .. now active".
lvscan says "Volume group ... not found"
mount fails.
what should i try next?
regards, Chris
PS: about the stripes, I don't think I have any.
Quoted 36 lines · Heinz Mauelshagen
vgchange -ay --partial
Quoted 31 lines · Graham Wood
Quoted 1 line · chris
I have create a volume group with 4 250GByte harddisks with an ext3
file
Quoted 1 line
system on the 1TB result.
Stripe or concat?
Quoted 1 line
now the third harddisk failed and the volume group is "dead" -
obviously.
The way you created the volume had no redundancy - therefore 25% of your data is gone, as well as the volume's "completeness".If you did a concat, then you (with playing) may be able to get some data back from the first 500GB of the volume - but I wouldn't want to rely on anything that came back from it. I'd suggest getting hold of 2 identical blank disks, and doing a binary (dd) copy of disks 1 and 2 to them - and then work on them. You might be able to use vgcfg{backup,restore} to tell the system that this volume is actually only on 2 disks.... However, anything that references data > 500GB into the volume is almost definitely lost - because although you've got 750G-1TB, it's almost all going to be linked back into the section that you've lost.
If you did a stripe, then you can forget getting any data back off it. You've lost every 4th block of whatever size you striped on. E.g. with a 64k stripe size, you'll have lost from 128k-192k, 384k-448k, etc. - and there's almost definitely going to be nothing salvagable from that.
Graham
_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/
Quoted 11 lines · chris
Thanks Heinz,
this looks like what i was serching for. still, it didn't work out.
the first call of this command issued (apart from multiple "couln't find device..")
"device-mapper ioctl cmd 9 failed: Das Argument ist ung�ltig"
(i hate german error messages, who invented this? it says "illegal
argument")but also "1 logic voliume(s) .. now active".
Well, looks like your Logical Volume got activated. Of course with a hole punched out (the missing drive).
Try to mount it manually.
Heinz
Quoted 62 lines
lvscan says "Volume group ... not found"
mount fails.what should i try next?
regards, Chris
PS: about the stripes, I don't think I have any.
Quoted 47 lines · Heinz Mauelshagen
vgchange -ay --partial
Quoted 42 lines · Graham Wood
Quoted 1 line · chris
I have create a volume group with 4 250GByte harddisks with an ext3
file
Quoted 1 line
system on the 1TB result.
Stripe or concat?
Quoted 1 line
now the third harddisk failed and the volume group is "dead" -
obviously.
The way you created the volume had no redundancy - therefore 25% of your data is gone, as
well as the volume's "completeness".If you did a concat, then you (with playing) may be able to get some data back from the
first 500GB of the volume - but I wouldn't want to rely on anything that came back from it.
I'd suggest getting hold of 2 identical blank disks, and doing a binary (dd) copy of disks 1
and 2 to them - and then work on them. You might be able to use vgcfg{backup,restore} to
tell the system that this volume is actually only on 2 disks.... However, anything that
references data > 500GB into the volume is almost definitely lost - because although you've
got 750G-1TB, it's almost all going to be linked back into the section that you've lost.If you did a stripe, then you can forget getting any data back off it. You've lost every
4th block of whatever size you striped on. E.g. with a 64k stripe size, you'll have lost
from 128k-192k, 384k-448k, etc. - and there's almost definitely going to be nothing
salvagable from that.Graham
_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/
Quoted 5 lines
_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Heinz Mauelshagen Red Hat GmbH
Consulting Development Engineer Am Sonnenhang 11
Storage Development 56242 Marienrachdorf
Germany
[email protected] PHONE +49 171 7803392
FAX +49 2626 924446=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-