Skip to contentSkip to conversation

USB devices fail unnecessarily on unpowered hubs

DISCUSSION Robert Hancock 2 participants 3 messages Jun 1, 2006 – Jun 2, 2006 5 messages not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

#3 lore raw
Quoted 6 lines · linux-os (Dick Johnson)

Many, most, perhaps all such devices don't take more power when they are "enabled". Everything is already running and sucking up maximum current when you plug it in! If the motherboard didn't smoke when the device was plugged in, you might just as well let the user use it! Perhaps a ** WARNING ** message somewhere, but by golly, they got it running or else you wouldn't be able to read its parameters.

Wrong.. USB devices are not allowed to draw more than some amount (100 mA I think) of power before the host tells it that it is allowed to switch into full-power mode. Any device that doesn't do this doesn't comply with the USB specs. Therefore it is very possible to connect a device and discover that it can't be enabled.

Signature · 3 lines
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from [email protected]
Home Page: http://www.roberthancock.com/
#4 lore raw
Quoted 8 lines · On Thu, 01 Jun 2006 17:35:22 -0600 Robert Hancock wrote:
Quoted 6 lines · linux-os (Dick Johnson)

Many, most, perhaps all such devices don't take more power when they are "enabled". Everything is already running and sucking up maximum current when you plug it in! If the motherboard didn't smoke when the device was plugged in, you might just as well let the user use it! Perhaps a ** WARNING ** message somewhere, but by golly, they got it running or else you wouldn't be able to read its parameters.

Quoted 5 lines

Wrong.. USB devices are not allowed to draw more than some amount (100 mA I think) of power before the host tells it that it is allowed to switch into full-power mode. Any device that doesn't do this doesn't comply with the USB specs. Therefore it is very possible to connect a device and discover that it can't be enabled.

so does Thunderbird on Windows have absolutely no Reply-to-All and no References or In-Reply-To capabilities?

---
~Randy

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

#7 lore raw
Quoted 8 lines · David Liontooth

It's clearly a good thing to be testing for this. As Alan points out, 100mA is the maximum permitted pre-configuration draw, so what a device draws when plugged in is not informative.

However, obeying the USB power rules is not an end in itself -- the relevant question is the minimum power the device requires to operate correctly and without damage.

Quoted 5 lines

The MaxPower value does not appear to be a reliable index of this. My USB stick has a MaxPower value of 178mA and works flawlessly off an unpowered hub. Unfortunately devices don't seem to tell us what their minimum power requirements are, so we need more flexibility in writing rules for this.

The fact it appears to work on an unpowered hub doesn't mean anything. Why would the manufacturer specify it can consume 178 mA if it couldn't consume that much under some conditions? Have you measured it? What makes you think that the hub can supply that much power on all ports at the same time despite not being specified to do so?

Trying to say "Well, it says it needs this much, but it probably doesn't really NEED that much.." is an unreliable guessing game.

Quoted 8 lines

udev could surely pick up on the MaxPower value and tolerate up to a 100% underrun on USB flash drives. That would likely still 90% of the pain right there, maybe all of it.

What are the reasons not to do this? What happens if a USB stick is underpowered to one unit? Nothing? Slower transmission? Data loss? Flash memory destruction? If it's just speed, it's a price well worth paying.

If the device can't get enough power, all kinds of bad stuff can happen.
This is the reason why USB power budgeting is part of the standard in
the first place. The kernel has no business ignoring such restrictions, not without a clearly-marked-as-dangerous user choice.

Quoted 5 lines

This is a great opportunity for a small exercise in empathy, utilizing that little long-neglected mirror neuron. Thousands of USB sticks inexplicably go dead in people's familiar hubs on keyboards and desks; Linux kernel coders dream sweet dreams of not violating USB power rules. I appreciate Andrew's support for a real-worldly solution.

Keep in mind that Windows will not permit the USB device to work in such configurations either. Windows always did the right thing here. Linux did not do the right thing before, and now it does.

Signature · 3 lines
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from [email protected]
Home Page: http://www.roberthancock.com/