e100: disable interrupts at boot
Subsystems (3)
PATCH 5/8 e100: disable interrupts at boot
From: Bjorn Helgaas <[email protected]>
Apparently the Intel PRO/100 device enables interrupts on reset. Unless firmware explicitly disables PRO/100 interrupts, we can get a flood of interrupts when a driver attaches to an unrelated device that happens to share the PRO/100 IRQ.
This should resolve this "irq 11: nobody cared" bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=5918
Signed-off-by Bjorn Helgaas <[email protected]>
Cc Jesse Brandeburg <[email protected]>
Cc Jeff Kirsher <[email protected]>
Cc John Ronciak <[email protected]>
Cc <[email protected]>
Cc <[email protected]>
Signed-off-by Andrew Morton <[email protected]>
---
drivers/pci/quirks.c | 57 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 57 insertions(+)
drivers/pci/quirks.c renamed from drivers/pci/quirks.c~e100-disable-interrupts-at-boot +57 -0
@@ -1390,6 +1390,63 @@ static void __devinit quirk_netmos(struc }DECLARE_PCI_FIXUP_HEADER (PCI_VENDOR_ID_NETMOS ,PCI_ANY_ID , quirk_netmos); +static void __devinit quirk_e100_interrupt (struct pci_dev *dev) +{ +u16 command; +u32 bar; +u8 __iomem *csr; +u8 cmd_hi; + +switch (dev->device) { +/* PCI IDs taken from drivers/net/e100.c */ +case 0x1029 : + case 0x1030 ... 0x1034: + case 0x1038 ... 0x103E: + case 0x1050 ... 0x1057: +case 0x1059 : + case 0x1064 ... 0x106B: + case 0x1091 ... 0x1095: +case 0x1209 : +case 0x1229 : +case 0x2449 : +case 0x2459 : +case 0x245D : +case 0x27DC : +break ; +default : +return ; + } + +/* +* Some firmware hands off the e100 with interrupts enabled, +* which can cause a flood of interrupts if packets are +* received before the driver attaches to the device. So +* disable all e100 interrupts here. The driver will +* re-enable them when it's ready. +*/ +pci_read_config_word (dev,PCI_COMMAND , &command); +pci_read_config_dword (dev,PCI_BASE_ADDRESS_0 , &bar); + +if (!(command &PCI_COMMAND_MEMORY ) || !bar) +return ; + + csr =ioremap (bar,8 ); +if (!csr) { +printk (KERN_WARNING "PCI: Can't map %s e100 registers\n" , +pci_name (dev)); +return ; + } + + cmd_hi =readb (csr +3 ); +if (cmd_hi ==0 ) { +printk (KERN_WARNING "PCI: Firmware left %s e100 interrupts " +"enabled, disabling\n" ,pci_name (dev)); +writeb (1 , csr +3 ); + } + +iounmap (csr); +} +DECLARE_PCI_FIXUP_EARLY (PCI_VENDOR_ID_INTEL ,PCI_ANY_ID , quirk_e100_interrupt);static void __devinit fixup_rev1_53c810 (struct pci_dev * dev) {
_