Skip to contentSkip to conversation

libata: convert several bmdma-style controllers to new EH

PATCH In review Tejun Heo 2 participants 7 messages Jun 13, 2006 – Jun 20, 2006

Subsystems (2)
lore
Share & tools
lore

Tejun Heo

author
#0 lore raw

PATCH 1/1 libata: convert several bmdma-style controllers to new EH

Convert sata_sis, svw, uli and vsc drivers to new EH. All the drivers used to specify ATA_FLAG_SATA_RESET to tell libata to use SATA hardreset instead of SRST.

This patch preserves the behavior by defining private error handler for each driver which only supports SATA hardreset. It is likely that all these controllers support SRST and can simply use the stock bmdma EH. The private EH methods will be removed after each driver is tested w/ the stock bmdma EH.

---

 drivers/scsi/sata_sis.c |   14 ++++++++++----
 drivers/scsi/sata_svw.c |   16 ++++++++++++----
 drivers/scsi/sata_uli.c |   15 ++++++++++-----
 drivers/scsi/sata_vsc.c |   12 +++++++++---
 4 files changed, 41 insertions(+), 16 deletions(-)

f8619ec9d9eb62a5b730c69836f7333f7f69661d

drivers/scsi/sata_sis.c +10 -4
index a07e6e5..9d305be 100644
@@ -64,6 +64,7 @@ enum {
 };
 
 static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static void sis_error_handler (struct ata_port *ap);
 static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg);
 static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
 
@@ -107,7 +108,6 @@ static const struct ata_port_operations 
 	.check_status		= ata_check_status,
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
-	.phy_reset		= sata_phy_reset,
 	.bmdma_setup            = ata_bmdma_setup,
 	.bmdma_start            = ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -115,7 +115,8 @@ static const struct ata_port_operations 
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_pio_data_xfer,
-	.eng_timeout		= ata_eng_timeout,
+	.error_handler		= sis_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= sis_scr_read,
@@ -127,8 +128,7 @@ static const struct ata_port_operations 
 
 static struct ata_port_info sis_port_info = {
 	.sht		= &sis_sht,
-	.host_flags	= ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
-			  ATA_FLAG_NO_LEGACY,
+	.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
 	.pio_mask	= 0x1f,
 	.mwdma_mask	= 0x7,
 	.udma_mask	= 0x7f,
@@ -234,6 +234,12 @@ static void sis_scr_write (struct ata_po
 	}
 }
 
+static void sis_error_handler (struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, ata_std_prereset, NULL, sata_std_hardreset,
+			   ata_std_postreset);
+}
+
 static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	static int printed_version;
drivers/scsi/sata_svw.c +12 -4
index d9b5168..e46ed41 100644
@@ -237,6 +237,14 @@ static u8 k2_stat_check_status(struct at
        	return readl((void *) ap->ioaddr.status_addr);
 }
 
+
+static void k2_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, ata_std_prereset, NULL, sata_std_hardreset,
+			   ata_std_postreset);
+}
+
+
 #ifdef CONFIG_PPC_OF
 /*
  * k2_sata_proc_info
@@ -314,7 +322,6 @@ static const struct ata_port_operations 
 	.check_status		= k2_stat_check_status,
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
-	.phy_reset		= sata_phy_reset,
 	.bmdma_setup		= k2_bmdma_setup_mmio,
 	.bmdma_start		= k2_bmdma_start_mmio,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -322,7 +329,8 @@ static const struct ata_port_operations 
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_mmio_data_xfer,
-	.eng_timeout		= ata_eng_timeout,
+	.error_handler		= k2_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= k2_sata_scr_read,
@@ -422,8 +430,8 @@ static int k2_sata_init_one (struct pci_
 	writel(0x0, mmio_base + K2_SATA_SIM_OFFSET);
 
 	probe_ent->sht = &k2_sata_sht;
-	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
-				ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO;
+	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				ATA_FLAG_MMIO;
 	probe_ent->port_ops = &k2_sata_ops;
 	probe_ent->n_ports = 4;
 	probe_ent->irq = pdev->irq;
drivers/scsi/sata_uli.c +10 -5
index e69ba22..48d26ce 100644
@@ -58,6 +58,7 @@ struct uli_priv {
 };
 
 static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static void uli_error_handler (struct ata_port *ap);
 static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg);
 static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
 
@@ -103,8 +104,6 @@ static const struct ata_port_operations 
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
 
-	.phy_reset		= sata_phy_reset,
-
 	.bmdma_setup            = ata_bmdma_setup,
 	.bmdma_start            = ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -113,7 +112,8 @@ static const struct ata_port_operations 
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_pio_data_xfer,
 
-	.eng_timeout		= ata_eng_timeout,
+	.error_handler		= uli_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
@@ -128,8 +128,7 @@ static const struct ata_port_operations 
 
 static struct ata_port_info uli_port_info = {
 	.sht            = &uli_sht,
-	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
-			  ATA_FLAG_NO_LEGACY,
+	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
 	.pio_mask       = 0x1f,		/* pio0-4 */
 	.udma_mask      = 0x7f,		/* udma0-6 */
 	.port_ops       = &uli_ops,
@@ -182,6 +181,12 @@ static void uli_scr_write (struct ata_po
 	uli_scr_cfg_write(ap, sc_reg, val);
 }
 
+static void uli_error_handler (struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, ata_std_prereset, NULL, sata_std_hardreset,
+			   ata_std_postreset);
+}
+
 static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	static int printed_version;
drivers/scsi/sata_vsc.c +9 -3
index 22ca7b8..5c909c2 100644
@@ -264,6 +264,12 @@ static irqreturn_t vsc_sata_interrupt (i
 	return IRQ_RETVAL(handled);
 }
 
+static void vsc_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, ata_std_prereset, NULL, sata_std_hardreset,
+			   ata_std_postreset);
+}
+
 
 static struct scsi_host_template vsc_sata_sht = {
 	.module			= THIS_MODULE,
@@ -291,7 +297,6 @@ static const struct ata_port_operations 
 	.exec_command		= ata_exec_command,
 	.check_status		= ata_check_status,
 	.dev_select		= ata_std_dev_select,
-	.phy_reset		= sata_phy_reset,
 	.bmdma_setup            = ata_bmdma_setup,
 	.bmdma_start            = ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -299,7 +304,8 @@ static const struct ata_port_operations 
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_pio_data_xfer,
-	.eng_timeout		= ata_eng_timeout,
+	.error_handler		= vsc_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.irq_handler		= vsc_sata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= vsc_sata_scr_read,
@@ -394,7 +400,7 @@ static int __devinit vsc_sata_init_one (
 
 	probe_ent->sht = &vsc_sata_sht;
 	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				ATA_FLAG_MMIO | ATA_FLAG_SATA_RESET;
+				ATA_FLAG_MMIO;
 	probe_ent->port_ops = &vsc_sata_ops;
 	probe_ent->n_ports = 4;
 	probe_ent->irq = pdev->irq;
Signature · 1 line
1.3.2
author
#1 lore raw
Quoted 9 lines · Tejun Heo

Convert sata_sis, svw, uli and vsc drivers to new EH. All the drivers used to specify ATA_FLAG_SATA_RESET to tell libata to use SATA hardreset instead of SRST.

This patch preserves the behavior by defining private error handler for each driver which only supports SATA hardreset. It is likely that all these controllers support SRST and can simply use the stock bmdma EH. The private EH methods will be removed after each driver is tested w/ the stock bmdma EH.

I forgot ->freeze/thaw. Please ignore this and the sata_via patch. Will repost them.

Signature · 1 line
tejun
author
#2 lore raw

PATCH 1/1 libata: convert several bmdma-style controllers to new EH, take #2

In reply to Tejun Heo

Convert sata_sis, svw, uli and vsc drivers to new EH. All the drivers used to specify ATA_FLAG_SATA_RESET to tell libata to use SATA hardreset instead of SRST.

This patch preserves the behavior by defining private error handler for each driver which only supports SATA hardreset. It is likely that all these controllers support SRST and can simply use the stock bmdma EH. The private EH methods will be removed after each driver is tested w/ the stock bmdma EH.

---

Only compile tested. I don't have access to any of controllers converted in this patch.

 drivers/scsi/sata_sis.c |   16 ++++++++++++----
 drivers/scsi/sata_svw.c |   18 ++++++++++++++----
 drivers/scsi/sata_uli.c |   17 ++++++++++++-----
 drivers/scsi/sata_vsc.c |   14 +++++++++++---
 4 files changed, 49 insertions(+), 16 deletions(-)

da84e39581054d4407b4a9a5ef3721a14b883767

drivers/scsi/sata_sis.c +12 -4
index a07e6e5..da627ce 100644
@@ -64,6 +64,7 @@ enum {
 };
 
 static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static void sis_error_handler (struct ata_port *ap);
 static u32 sis_scr_read (struct ata_port *ap, unsigned int sc_reg);
 static void sis_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
 
@@ -107,7 +108,6 @@ static const struct ata_port_operations 
 	.check_status		= ata_check_status,
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
-	.phy_reset		= sata_phy_reset,
 	.bmdma_setup            = ata_bmdma_setup,
 	.bmdma_start            = ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -115,7 +115,10 @@ static const struct ata_port_operations 
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_pio_data_xfer,
-	.eng_timeout		= ata_eng_timeout,
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= sis_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= sis_scr_read,
@@ -127,8 +130,7 @@ static const struct ata_port_operations 
 
 static struct ata_port_info sis_port_info = {
 	.sht		= &sis_sht,
-	.host_flags	= ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
-			  ATA_FLAG_NO_LEGACY,
+	.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
 	.pio_mask	= 0x1f,
 	.mwdma_mask	= 0x7,
 	.udma_mask	= 0x7f,
@@ -234,6 +236,12 @@ static void sis_scr_write (struct ata_po
 	}
 }
 
+static void sis_error_handler (struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, ata_std_prereset, NULL, sata_std_hardreset,
+			   ata_std_postreset);
+}
+
 static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	static int printed_version;
drivers/scsi/sata_svw.c +14 -4
index d9b5168..724669c 100644
@@ -237,6 +237,14 @@ static u8 k2_stat_check_status(struct at
        	return readl((void *) ap->ioaddr.status_addr);
 }
 
+
+static void k2_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, ata_std_prereset, NULL, sata_std_hardreset,
+			   ata_std_postreset);
+}
+
+
 #ifdef CONFIG_PPC_OF
 /*
  * k2_sata_proc_info
@@ -314,7 +322,6 @@ static const struct ata_port_operations 
 	.check_status		= k2_stat_check_status,
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
-	.phy_reset		= sata_phy_reset,
 	.bmdma_setup		= k2_bmdma_setup_mmio,
 	.bmdma_start		= k2_bmdma_start_mmio,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -322,7 +329,10 @@ static const struct ata_port_operations 
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_mmio_data_xfer,
-	.eng_timeout		= ata_eng_timeout,
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= k2_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= k2_sata_scr_read,
@@ -422,8 +432,8 @@ static int k2_sata_init_one (struct pci_
 	writel(0x0, mmio_base + K2_SATA_SIM_OFFSET);
 
 	probe_ent->sht = &k2_sata_sht;
-	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
-				ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO;
+	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				ATA_FLAG_MMIO;
 	probe_ent->port_ops = &k2_sata_ops;
 	probe_ent->n_ports = 4;
 	probe_ent->irq = pdev->irq;
drivers/scsi/sata_uli.c +12 -5
index e69ba22..685ac95 100644
@@ -58,6 +58,7 @@ struct uli_priv {
 };
 
 static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static void uli_error_handler (struct ata_port *ap);
 static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg);
 static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
 
@@ -103,8 +104,6 @@ static const struct ata_port_operations 
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
 
-	.phy_reset		= sata_phy_reset,
-
 	.bmdma_setup            = ata_bmdma_setup,
 	.bmdma_start            = ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -113,7 +112,10 @@ static const struct ata_port_operations 
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_pio_data_xfer,
 
-	.eng_timeout		= ata_eng_timeout,
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= uli_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
@@ -128,8 +130,7 @@ static const struct ata_port_operations 
 
 static struct ata_port_info uli_port_info = {
 	.sht            = &uli_sht,
-	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
-			  ATA_FLAG_NO_LEGACY,
+	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
 	.pio_mask       = 0x1f,		/* pio0-4 */
 	.udma_mask      = 0x7f,		/* udma0-6 */
 	.port_ops       = &uli_ops,
@@ -182,6 +183,12 @@ static void uli_scr_write (struct ata_po
 	uli_scr_cfg_write(ap, sc_reg, val);
 }
 
+static void uli_error_handler (struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, ata_std_prereset, NULL, sata_std_hardreset,
+			   ata_std_postreset);
+}
+
 static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	static int printed_version;
drivers/scsi/sata_vsc.c +11 -3
index 22ca7b8..508ed20 100644
@@ -264,6 +264,12 @@ static irqreturn_t vsc_sata_interrupt (i
 	return IRQ_RETVAL(handled);
 }
 
+static void vsc_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, ata_std_prereset, NULL, sata_std_hardreset,
+			   ata_std_postreset);
+}
+
 
 static struct scsi_host_template vsc_sata_sht = {
 	.module			= THIS_MODULE,
@@ -291,7 +297,6 @@ static const struct ata_port_operations 
 	.exec_command		= ata_exec_command,
 	.check_status		= ata_check_status,
 	.dev_select		= ata_std_dev_select,
-	.phy_reset		= sata_phy_reset,
 	.bmdma_setup            = ata_bmdma_setup,
 	.bmdma_start            = ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -299,7 +304,10 @@ static const struct ata_port_operations 
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_pio_data_xfer,
-	.eng_timeout		= ata_eng_timeout,
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= vsc_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.irq_handler		= vsc_sata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= vsc_sata_scr_read,
@@ -394,7 +402,7 @@ static int __devinit vsc_sata_init_one (
 
 	probe_ent->sht = &vsc_sata_sht;
 	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				ATA_FLAG_MMIO | ATA_FLAG_SATA_RESET;
+				ATA_FLAG_MMIO;
 	probe_ent->port_ops = &vsc_sata_ops;
 	probe_ent->n_ports = 4;
 	probe_ent->irq = pdev->irq;
Signature · 1 line
1.3.2
#3 lore raw

Re: [PATCH] libata: convert several bmdma-style controllers to new EH, take #2

Quoted 11 lines · Tejun Heo

Convert sata_sis, svw, uli and vsc drivers to new EH. All the drivers used to specify ATA_FLAG_SATA_RESET to tell libata to use SATA hardreset instead of SRST.

This patch preserves the behavior by defining private error handler for each driver which only supports SATA hardreset. It is likely that all these controllers support SRST and can simply use the stock bmdma EH. The private EH methods will be removed after each driver is tested w/ the stock bmdma EH.

Too cautious :) I don't want to add the duplicate code, and then just remove it later when things are they are supposed to work.

Just make sure your changes will either (a) work or (b) fail in an obvious way :)

Then call for testers...

Jeff

author
#4 lore raw

Re: [PATCH] libata: convert several bmdma-style controllers to new EH, take #2

Quoted 11 lines · Jeff Garzik
Quoted 10 lines · Tejun Heo

Convert sata_sis, svw, uli and vsc drivers to new EH. All the drivers used to specify ATA_FLAG_SATA_RESET to tell libata to use SATA hardreset instead of SRST.

This patch preserves the behavior by defining private error handler for each driver which only supports SATA hardreset. It is likely that all these controllers support SRST and can simply use the stock bmdma EH. The private EH methods will be removed after each driver is tested w/ the stock bmdma EH.

Quoted 7 lines
Quoted 1 line

Too cautious :) I don't want to add the duplicate code, and then just remove it later when things are they are supposed to work.

Just make sure your changes will either (a) work or (b) fail in an obvious way :)

Then call for testers...

Cool, I like that. For get this and the via patch. Will post braver version tomorrow. :)

Signature · 1 line
tejun
author
#5 lore raw

PATCH 1/1 libata: convert several bmdma-style controllers to new EH, take #3

In reply to Jeff Garzik

Convert sata_sis, svw, uli and vsc drivers to new EH. All the drivers used to specify ATA_FLAG_SATA_RESET to tell libata to use SATA hardreset instead of SRST. This patch makes all the converted drivers use the standard bmdma error handler which uses both SRST and SATA hardreset.

All the controllers should be able to perform SRST but still needs verification. If some of the controllers can't do SRST, it will be very easy to spot as it will show up during boot probing.

---

 drivers/scsi/sata_sis.c |    9 +++++----
 drivers/scsi/sata_svw.c |   10 ++++++----
 drivers/scsi/sata_uli.c |   10 +++++-----
 drivers/scsi/sata_vsc.c |    8 +++++---
 4 files changed, 21 insertions(+), 16 deletions(-)

eb59dcb94d562917d22ec0c3a820ae6ae9f22910

drivers/scsi/sata_sis.c +5 -4
index a07e6e5..809d337 100644
@@ -107,7 +107,6 @@ static const struct ata_port_operations 
 	.check_status		= ata_check_status,
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
-	.phy_reset		= sata_phy_reset,
 	.bmdma_setup            = ata_bmdma_setup,
 	.bmdma_start            = ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -115,7 +114,10 @@ static const struct ata_port_operations 
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_pio_data_xfer,
-	.eng_timeout		= ata_eng_timeout,
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= ata_bmdma_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= sis_scr_read,
@@ -127,8 +129,7 @@ static const struct ata_port_operations 
 
 static struct ata_port_info sis_port_info = {
 	.sht		= &sis_sht,
-	.host_flags	= ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
-			  ATA_FLAG_NO_LEGACY,
+	.host_flags	= ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
 	.pio_mask	= 0x1f,
 	.mwdma_mask	= 0x7,
 	.udma_mask	= 0x7f,
drivers/scsi/sata_svw.c +6 -4
index d9b5168..c94b870 100644
@@ -314,7 +314,6 @@ static const struct ata_port_operations 
 	.check_status		= k2_stat_check_status,
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
-	.phy_reset		= sata_phy_reset,
 	.bmdma_setup		= k2_bmdma_setup_mmio,
 	.bmdma_start		= k2_bmdma_start_mmio,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -322,7 +321,10 @@ static const struct ata_port_operations 
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_mmio_data_xfer,
-	.eng_timeout		= ata_eng_timeout,
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= ata_bmdma_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= k2_sata_scr_read,
@@ -422,8 +424,8 @@ static int k2_sata_init_one (struct pci_
 	writel(0x0, mmio_base + K2_SATA_SIM_OFFSET);
 
 	probe_ent->sht = &k2_sata_sht;
-	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
-				ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO;
+	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+				ATA_FLAG_MMIO;
 	probe_ent->port_ops = &k2_sata_ops;
 	probe_ent->n_ports = 4;
 	probe_ent->irq = pdev->irq;
drivers/scsi/sata_uli.c +5 -5
index e69ba22..f668c99 100644
@@ -103,8 +103,6 @@ static const struct ata_port_operations 
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,
 
-	.phy_reset		= sata_phy_reset,
-
 	.bmdma_setup            = ata_bmdma_setup,
 	.bmdma_start            = ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -113,7 +111,10 @@ static const struct ata_port_operations 
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_pio_data_xfer,
 
-	.eng_timeout		= ata_eng_timeout,
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= ata_bmdma_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 
 	.irq_handler		= ata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
@@ -128,8 +129,7 @@ static const struct ata_port_operations 
 
 static struct ata_port_info uli_port_info = {
 	.sht            = &uli_sht,
-	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
-			  ATA_FLAG_NO_LEGACY,
+	.host_flags     = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY,
 	.pio_mask       = 0x1f,		/* pio0-4 */
 	.udma_mask      = 0x7f,		/* udma0-6 */
 	.port_ops       = &uli_ops,
drivers/scsi/sata_vsc.c +5 -3
index 22ca7b8..d92e3dd 100644
@@ -291,7 +291,6 @@ static const struct ata_port_operations 
 	.exec_command		= ata_exec_command,
 	.check_status		= ata_check_status,
 	.dev_select		= ata_std_dev_select,
-	.phy_reset		= sata_phy_reset,
 	.bmdma_setup            = ata_bmdma_setup,
 	.bmdma_start            = ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
@@ -299,7 +298,10 @@ static const struct ata_port_operations 
 	.qc_prep		= ata_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_pio_data_xfer,
-	.eng_timeout		= ata_eng_timeout,
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= ata_bmdma_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.irq_handler		= vsc_sata_interrupt,
 	.irq_clear		= ata_bmdma_irq_clear,
 	.scr_read		= vsc_sata_scr_read,
@@ -394,7 +396,7 @@ static int __devinit vsc_sata_init_one (
 
 	probe_ent->sht = &vsc_sata_sht;
 	probe_ent->host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
-				ATA_FLAG_MMIO | ATA_FLAG_SATA_RESET;
+				ATA_FLAG_MMIO;
 	probe_ent->port_ops = &vsc_sata_ops;
 	probe_ent->n_ports = 4;
 	probe_ent->irq = pdev->irq;
Signature · 1 line
1.3.2
#6 lore raw

Re: [PATCH] libata: convert several bmdma-style controllers to new EH, take #3

Quoted 11 lines · Tejun Heo

Convert sata_sis, svw, uli and vsc drivers to new EH. All the drivers used to specify ATA_FLAG_SATA_RESET to tell libata to use SATA hardreset instead of SRST. This patch makes all the converted drivers use the standard bmdma error handler which uses both SRST and SATA hardreset.

All the controllers should be able to perform SRST but still needs verification. If some of the controllers can't do SRST, it will be very easy to spot as it will show up during boot probing.

Applied, let's see how testing works out...

I can test sata_svw easily, and sata_vsc with some effort. I might have ULi or SiS motherboards around too, unsure.

Jeff