2.6.17-rc[56]-mm*: pcmcia "I/O resource not free"
The PCMCIA slot on my Thinkpad X40 stopped working sometime between 2.6.17-rc4-mm3 and 2.6.17-rc5-mm3, and is still not working as of 2.6.17-rc6-mm2. There's one diff early in dmesg that looks interesting:
ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1f.6 to 64 MC'97 1 converters and GPIO not ready (0xff00)
PM: Adding info for ac97:1-1:unknown codec
-ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
Yenta: CardBus bridge found at 0000:02:00.0 [1014:0555]
-Yenta: ISA IRQ mask 0x04b8, PCI irq 169
+Yenta: ISA IRQ mask 0x0cb8, PCI irq 169
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff
cs: IO port probe 0x3000-0x7fff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xdfffffff
pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf7ffffff
Then when I insert the card, instead of
pccard: PCMCIA card inserted into slot 0
cs: memory probe 0xf0000000-0xf7ffffff: excluding 0xf0000000-0xf7ffffff
cs: memory probe 0xd0200000-0xdfffffff: excluding 0xd0200000-0xd11fffff
0xd1a00000-0xd41fffff 0xd4a00000-0xd51fffff 0xd5a00000-0xd61fffff
0xd6a00000-0xd71fffff 0xd7a00000-0xd81fffff 0xd8a00000-0xd91fffff
0xd9a00000-0xda1fffff 0xdaa00000-0xdb1fffff 0xdba00000-0xdc1fffff
0xdca00000-0xdd1fffff 0xdda00000-0xde1fffff 0xdea00000-0xdf1fffff
0xdfa00000-0xe01fffff pcmcia: registering new device pcmcia0.0
PM: Adding info for pcmcia:0.0
-Probing IDE interface ide2...
-hde: CF Card, CFA DISK drive
-PM: Adding info for No Bus:ide2
-hdf: probing with STATUS(0x50) instead of ALTSTATUS(0x0a)
I get
pccard: PCMCIA card inserted into slot 0
cs: memory probe 0xf0000000-0xf7ffffff: excluding 0xf0000000-0xf7ffffff
cs: memory probe 0xd0200000-0xdfffffff: excluding 0xd0200000-0xd11fffff
0xd1a00000-0xd41fffff 0xd4a00000-0xd51fffff 0xd5a00000-0xd61fffff
0xd6a00000-0xd71fffff 0xd7a00000-0xd81fffff 0xd8a00000-0xd91fffff
0xd9a00000-0xda1fffff 0xdaa00000-0xdb1fffff 0xdba00000-0xdc1fffff
0xdca00000-0xdd1fffff 0xdda00000-0xde1fffff 0xdea00000-0xdf1fffff
0xdfa00000-0xe01fffff pcmcia: registering new device pcmcia0.0
PM: Adding info for pcmcia:0.0
+ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A01E-0xF8A8A01E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probe
With 2.6.17-rc6-mm2 I have
CPU0
0: 188343 IO-APIC-edge timer 1: 2685 IO-APIC-edge i8042 9: 393 IO-APIC-fasteoi acpi 12: 17840 IO-APIC-edge i8042 14: 4616 IO-APIC-edge ide0 169: 1 IO-APIC-fasteoi uhci_hcd:usb1, yenta 177: 0 IO-APIC-fasteoi Intel 82801DB-ICH4, Intel 82801DB-ICH4 Modem 185: 0 IO-APIC-fasteoi uhci_hcd:usb3 193: 0 IO-APIC-fasteoi uhci_hcd:usb2 201: 0 IO-APIC-fasteoi ehci_hcd:usb4 209: 2524 IO-APIC-fasteoi eth0 217: 43647 IO-APIC-fasteoi ipw2200 NMI: 0 LOC: 175985 ERR: 0 MIS: 0
The card I'm trying to use is a "PQI Compact Flash Adapter", which appears to just be some wires connecting the PCMCIA pins to the CF pins. The CF card is a "TwinMOS Ultra-X 140X 1GB" card, part number FCF1GBUPS-K W543F5TM0832.
dmesgs at
http://web.hexapodia.org/~adi/tmp/dmesg.2.6.17-rc4-mm3.txt
http://web.hexapodia.org/~adi/tmp/dmesg.2.6.17-rc6-mm2.txt
(although the rc4-mm3 one is truncated, sorry.)
-andy
Quoted 79 lines · On Thu, 15 Jun 2006 09:28:59 -0700 Andy Isaacson <[email protected]> wrote:
The PCMCIA slot on my Thinkpad X40 stopped working sometime between 2.6.17-rc4-mm3 and 2.6.17-rc5-mm3, and is still not working as of 2.6.17-rc6-mm2. There's one diff early in dmesg that looks interesting:
ACPI: PCI Interrupt 0000:00:1f.6[B] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1f.6 to 64 MC'97 1 converters and GPIO not ready (0xff00)
PM: Adding info for ac97:1-1:unknown codec(quoted diff) +1
-2-ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169 Yenta: CardBus bridge found at 0000:02:00.0 [1014:0555] -Yenta: ISA IRQ mask 0x04b8, PCI irq 169 +Yenta: ISA IRQ mask 0x0cb8, PCI irq 169 Socket status: 30000006 pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff cs: IO port probe 0x3000-0x7fff: clean. pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xdfffffff pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf7ffffffThen when I insert the card, instead of
pccard: PCMCIA card inserted into slot 0
cs: memory probe 0xf0000000-0xf7ffffff: excluding 0xf0000000-0xf7ffffff
cs: memory probe 0xd0200000-0xdfffffff: excluding 0xd0200000-0xd11fffff0xd1a00000-0xd41fffff 0xd4a00000-0xd51fffff 0xd5a00000-0xd61fffff 0xd6a00000-0xd71fffff 0xd7a00000-0xd81fffff 0xd8a00000-0xd91fffff 0xd9a00000-0xda1fffff 0xdaa00000-0xdb1fffff 0xdba00000-0xdc1fffff 0xdca00000-0xdd1fffff 0xdda00000-0xde1fffff 0xdea00000-0xdf1fffff 0xdfa00000-0xe01fffffpcmcia: registering new device pcmcia0.0
PM: Adding info for pcmcia:0.0(quoted diff) +0
-4-Probing IDE interface ide2... -hde: CF Card, CFA DISK drive -PM: Adding info for No Bus:ide2 -hdf: probing with STATUS(0x50) instead of ALTSTATUS(0x0a)I get
pccard: PCMCIA card inserted into slot 0
cs: memory probe 0xf0000000-0xf7ffffff: excluding 0xf0000000-0xf7ffffff
cs: memory probe 0xd0200000-0xdfffffff: excluding 0xd0200000-0xd11fffff0xd1a00000-0xd41fffff 0xd4a00000-0xd51fffff 0xd5a00000-0xd61fffff 0xd6a00000-0xd71fffff 0xd7a00000-0xd81fffff 0xd8a00000-0xd91fffff 0xd9a00000-0xda1fffff 0xdaa00000-0xdb1fffff 0xdba00000-0xdc1fffff 0xdca00000-0xdd1fffff 0xdda00000-0xde1fffff 0xdea00000-0xdf1fffff 0xdfa00000-0xe01fffffpcmcia: registering new device pcmcia0.0
PM: Adding info for pcmcia:0.0(quoted diff) +6
-0+ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A01E-0xF8A8A01E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probeWith 2.6.17-rc6-mm2 I have
CPU0
0: 188343 IO-APIC-edge timer 1: 2685 IO-APIC-edge i8042 9: 393 IO-APIC-fasteoi acpi 12: 17840 IO-APIC-edge i8042 14: 4616 IO-APIC-edge ide0 169: 1 IO-APIC-fasteoi uhci_hcd:usb1, yenta 177: 0 IO-APIC-fasteoi Intel 82801DB-ICH4, Intel 82801DB-ICH4 Modem 185: 0 IO-APIC-fasteoi uhci_hcd:usb3 193: 0 IO-APIC-fasteoi uhci_hcd:usb2 201: 0 IO-APIC-fasteoi ehci_hcd:usb4 209: 2524 IO-APIC-fasteoi eth0 217: 43647 IO-APIC-fasteoi ipw2200 NMI: 0 LOC: 175985 ERR: 0 MIS: 0The card I'm trying to use is a "PQI Compact Flash Adapter", which appears to just be some wires connecting the PCMCIA pins to the CF pins. The CF card is a "TwinMOS Ultra-X 140X 1GB" card, part number FCF1GBUPS-K W543F5TM0832.
Quoted 5 lines
dmesgs at
http://web.hexapodia.org/~adi/tmp/dmesg.2.6.17-rc4-mm3.txt
http://web.hexapodia.org/~adi/tmp/dmesg.2.6.17-rc6-mm2.txt
hm. I don't know who to blame for this yet ;)
The contents of /proc/ioports on both kernels might be useful. Let's see which device+driver is already using those ports, and whether the older kenrel uses the same addresses.
Thanks.
Quoted 3 lines · Andrew Morton
Quoted 3 lines
The PCMCIA slot on my Thinkpad X40 stopped working sometime between 2.6.17-rc4-mm3 and 2.6.17-rc5-mm3, and is still not working as of 2.6.17-rc6-mm2.
[snip]
Quoted 13 lines
Review
Quoted 10 lines
(quoted diff) +6
-4-Probing IDE interface ide2... -hde: CF Card, CFA DISK drive -PM: Adding info for No Bus:ide2 -hdf: probing with STATUS(0x50) instead of ALTSTATUS(0x0a) +ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A01E-0xF8A8A01E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probehm. I don't know who to blame for this yet ;)
Quoted 3 lines
The contents of
/proc/ioportson both kernels might be useful. Let's see which device+driver is already using those ports, and whether the older kenrel uses the same addresses.
In further testing, -rc6 is fine while -rc6-mm2 fails.
Under 2.6.17-rc6 (after having inserted and removed the card, but that doesn't seem to make much difference) I have
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
03c0-03df : vga+
03f6-03f6 : ide0
1000-107f : 0000:00:1f.0
1000-107f : motherboard
1000-1003 : PM1a_EVT_BLK
1004-1005 : PM1a_CNT_BLK
1008-100b : PM_TMR
1010-1015 : ACPI CPU throttle
1020-1020 : PM2_CNT_BLK
1028-102f : GPE0_BLK1180-11bf : 0000:00:1f.0
1180-11bf : motherboard
15e0-15ef : motherboard
1600-167f : motherboard
1680-169f : motherboard
1800-1807 : 0000:00:02.0
1810-181f : 0000:00:1f.1
1810-1817 : ide0
1818-181f : ide1
1820-183f : 0000:00:1d.0
1820-183f : uhci_hcd
1840-185f : 0000:00:1d.1
1840-185f : uhci_hcd
1860-187f : 0000:00:1d.2
1860-187f : uhci_hcd
1880-189f : 0000:00:1f.3
18c0-18ff : 0000:00:1f.5
18c0-18ff : Intel 82801DB-ICH4
1c00-1cff : 0000:00:1f.5
1c00-1cff : Intel 82801DB-ICH4
2000-207f : 0000:00:1f.6
2000-207f : Intel 82801DB-ICH4 Modem
2400-24ff : 0000:00:1f.6
2400-24ff : Intel 82801DB-ICH4 Modem
3000-7fff : PCI Bus #02
3000-30ff : PCI CardBus #03
3400-34ff : PCI CardBus #03
7000-703f : 0000:02:01.0
7000-703f : e1000
The diff between -rc6 and -rc6-mm2 shows that they have the same ioport assignment (there's only a textual diff due to ACPI string changes).
I've put just about everything you could want to know about the two kernels at
http://web.hexapodia.org/~adi/bobble/bobble_2.6.17-rc6_20060620093733/
and
http://web.hexapodia.org/~adi/bobble/bobble_2.6.17-rc6-mm2_20060620094254/
-andy
Quoted 19 lines · Andy Isaacson
Quoted 3 lines · Andrew Morton
Quoted 3 lines
The PCMCIA slot on my Thinkpad X40 stopped working sometime between 2.6.17-rc4-mm3 and 2.6.17-rc5-mm3, and is still not working as of 2.6.17-rc6-mm2.
[snip]
Quoted 13 lines
Review
Quoted 10 lines
(quoted diff) +6
-4-Probing IDE interface ide2... -hde: CF Card, CFA DISK drive -PM: Adding info for No Bus:ide2 -hdf: probing with STATUS(0x50) instead of ALTSTATUS(0x0a) +ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A01E-0xF8A8A01E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probehm. I don't know who to blame for this yet ;)
Quoted 5 lines
Quoted 3 lines
The contents of
/proc/ioportson both kernels might be useful. Let's see which device+driver is already using those ports, and whether the older kenrel uses the same addresses.In further testing, -rc6 is fine while -rc6-mm2 fails.
OK.
Quoted 5 lines
Under 2.6.17-rc6 (after having inserted and removed the card, but that doesn't seem to make much difference) I have
0000-001f : dma1
...
I should have said iomem, not ioports. But you have it there on those very detailed web pages. There's nothing at 0xF8A8Axxx in either kernel.
Quoted 2 lines
The diff between -rc6 and -rc6-mm2 shows that they have the same ioport assignment (there's only a textual diff due to ACPI string changes).
yep. The only reelvant diff in the rc6 versus rc6-mm2 /proc/iomem is:
@@ -29,7 +29,6 @@
d0220000-d0220fff : 0000:02:02.0
d0220000-d0220fff : ipw2200
d0221000-d02210ff : 0000:02:00.1
- d1200000-d1200fff : pcmcia_socket0
d2000000-d3ffffff : PCI CardBus #03
e0000000-e7ffffff : 0000:00:02.0
e8000000-efffffff : 0000:00:02.1
whch is to be expected if you removed the card.
Quoted 6 lines
I've put just about everything you could want to know about the two kernels at
http://web.hexapodia.org/~adi/bobble/bobble_2.6.17-rc6_20060620093733/
and
http://web.hexapodia.org/~adi/bobble/bobble_2.6.17-rc6-mm2_20060620094254/
It's strange (to me) that IDE is requesting a single-byte memory region. Possibly we've broken the resource.c code such that it has some off-by-one and is now rejecting single-byte requests.
If you're keen , the place to poke around is in
kernel/resource.c:__request_region(). Here's a starting patch:
kernel/resource.c renamed from kernel/resource.c~a +4 -0
@@ -501,6 +501,10 @@ struct resource * __request_region(struc conflict =__request_resource (parent, res);if (!conflict)break ; +printk ("conflict: %s[%Lx->%Lx]\n" , + conflict->name, + (unsigned long long )conflict->start, + (unsigned long long )conflict->end);if (conflict != parent) { parent = conflict;if (!(conflict->flags &IORESOURCE_BUSY ))
_
Which should tell us what we're allegedly conflicting with.
Then again, perhaps IDE is broken (as well?), because you don't have any single-byte iomem regions in your 2.6.17-rc6 /proc/iomem. It would be interesting to run this patch in both 2.6.17-rc6 and in 2.6.17-rc6-mm2, see what it says:
drivers/ide/ide.c renamed from drivers/ide/ide.c~a +4 -0
@@ -364,6 +364,10 @@ static struct resource* hwif_request_reg {struct resource *res =request_region (addr, num, hwif->name); +if (num ==1 ) { +printk ("%s: single-byte request\n" , __FUNCTION__); +dump_stack (); + }if (!res)printk (KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n" , hwif->name, addr, addr+num-1 );
_
Quoted 61 lines · On Tue, 20 Jun 2006 15:03:17 -0700 Andrew Morton wrote:
Quoted 19 lines · Andy Isaacson
Quoted 3 lines · Andrew Morton
Quoted 3 lines
The PCMCIA slot on my Thinkpad X40 stopped working sometime between 2.6.17-rc4-mm3 and 2.6.17-rc5-mm3, and is still not working as of 2.6.17-rc6-mm2.
[snip]
Quoted 13 lines
Review
Quoted 10 lines
(quoted diff) +6
-4-Probing IDE interface ide2... -hde: CF Card, CFA DISK drive -PM: Adding info for No Bus:ide2 -hdf: probing with STATUS(0x50) instead of ALTSTATUS(0x0a) +ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A01E-0xF8A8A01E not free. +ide2: ports already in use, skipping probe +ide2: I/O resource 0xF8A8A00E-0xF8A8A00E not free. +ide2: ports already in use, skipping probehm. I don't know who to blame for this yet ;)
Quoted 5 lines
Quoted 3 lines
The contents of
/proc/ioportson both kernels might be useful. Let's see which device+driver is already using those ports, and whether the older kenrel uses the same addresses.In further testing, -rc6 is fine while -rc6-mm2 fails.
OK.
Quoted 5 lines
Under 2.6.17-rc6 (after having inserted and removed the card, but that doesn't seem to make much difference) I have
0000-001f : dma1
...I should have said iomem, not ioports. But you have it there on those very detailed web pages. There's nothing at 0xF8A8Axxx in either kernel.
Quoted 2 lines
The diff between -rc6 and -rc6-mm2 shows that they have the same ioport assignment (there's only a textual diff due to ACPI string changes).
yep. The only reelvant diff in the rc6 versus rc6-mm2
/proc/iomemis:(quoted diff) +0
-1@@ -29,7 +29,6 @@ d0220000-d0220fff : 0000:02:02.0 d0220000-d0220fff : ipw2200 d0221000-d02210ff : 0000:02:00.1 - d1200000-d1200fff : pcmcia_socket0 d2000000-d3ffffff : PCI CardBus #03 e0000000-e7ffffff : 0000:00:02.0 e8000000-efffffff : 0000:00:02.1whch is to be expected if you removed the card.
Quoted 6 lines
I've put just about everything you could want to know about the two kernels at
http://web.hexapodia.org/~adi/bobble/bobble_2.6.17-rc6_20060620093733/
and
http://web.hexapodia.org/~adi/bobble/bobble_2.6.17-rc6-mm2_20060620094254/
Quoted 3 lines
It's strange (to me) that IDE is requesting a single-byte memory region. Possibly we've broken the
resource.ccode such that it has some off-by-one and is now rejecting single-byte requests.
Looks like ide.c uses single-byte requests just for checking region availability, but I would think that it should use full-sized requests for that.
Quoted 43 lines
If you're keen , the place to poke around is in
kernel/resource.c:__request_region(). Here's a starting patch:kernel/resource.c renamed from kernel/resource.c~a +4
-0@@ -501,6 +501,10 @@ struct resource * __request_region(struc conflict =__request_resource (parent, res);if (!conflict)break ; +printk ("conflict: %s[%Lx->%Lx]\n" , + conflict->name, + (unsigned long long )conflict->start, + (unsigned long long )conflict->end);if (conflict != parent) { parent = conflict;if (!(conflict->flags &IORESOURCE_BUSY ))_
Which should tell us what we're allegedly conflicting with.
Then again, perhaps IDE is broken (as well?), because you don't have any single-byte iomem regions in your 2.6.17-rc6
/proc/iomem. It would be interesting to run this patch in both 2.6.17-rc6 and in 2.6.17-rc6-mm2, see what it says:diff -puN
drivers/ide/ide.c~adrivers/ide/ide.cdrivers/ide/ide.c renamed from drivers/ide/ide.c~a +4
-0@@ -364,6 +364,10 @@ static struct resource* hwif_request_reg {struct resource *res =request_region (addr, num, hwif->name); +if (num ==1 ) { +printk ("%s: single-byte request\n" , __FUNCTION__); +dump_stack (); + }if (!res)printk (KERN_ERR "%s: I/O resource 0x%lX-0x%lX not free.\n" , hwif->name, addr, addr+num-1 );
Quoted 1 line
_
linux-2617-pv/drivers/ide> grep hwif_request_reg *.c ide.c:static struct resource* hwif_request_region(ide_hwif_t *hwif,ide.c: * ide_hwif_request_regions - request resources for IDE
ide.c:int ide_hwif_request_regions(ide_hwif_t *hwif)
ide.c: if (addr && !hwif_request_region(hwif, addr, 1))
ide.c: if (!hwif_request_region(hwif, addr, 8))
ide.c: if (!hwif_request_region(hwif, addr, 1)) {---
~Randy
Quoted 3 lines · Andrew Morton
It's strange (to me) that IDE is requesting a single-byte memory region. Possibly we've broken the
resource.ccode such that it has some off-by-one and is now rejecting single-byte requests.
[snip]
Quoted 2 lines
+++
a/kernel/resource.ckernel/resource.c renamed from kernel/resource.c~a +1
-0+ printk("conflict: %s[%Lx->%Lx]\n",
[snip]
Quoted 4 lines
Then again, perhaps IDE is broken (as well?), because you don't have any single-byte iomem regions in your 2.6.17-rc6
/proc/iomem. It would be interesting to run this patch in both 2.6.17-rc6 and in 2.6.17-rc6-mm2, see what it says:
[snip]
drivers/ide/ide.c static struct resource* hwif_request_reg · line 369
Quoted 3 lines
+++
25-akpm/drivers/ide/ide.cTue Jun 20 15:02:15 2006drivers/ide/ide.c renamed from drivers/ide/ide.c~a +2
-0+printk ("%s: single-byte request\n" , __FUNCTION__); +dump_stack ();
With both patches, rc6-mm2 dumps the following.
[ 2034.052000] pccard: PCMCIA card inserted into slot 0 [ 2034.052000] cs: memory probe 0xf0000000-0xf7ffffff: excluding 0xf0000000-0xf7ffffff [ 2034.052000] cs: memory probe 0xd0200000-0xdfffffff: excluding 0xd0200000-0xd11fffff 0xd1a00000-0xd41fffff 0xd4a00000-0xd51fffff 0xd5a00000-0xd61fffff 0xd6a00000-0xd71fffff 0xd7a00000-0xd81fffff 0xd8a00000-0xd91fffff 0xd9a00000-0xda1fffff 0xdaa00000-0xdb1fffff 0xdba00000-0xdc1fffff 0xdca00000-0xdd1fffff 0xdda00000-0xde1fffff 0xdea00000-0xdf1fffff 0xdfa00000-0xe01fffff [ 2034.060000] pcmcia: registering new device pcmcia0.0 [ 2034.060000] PM: Adding info for pcmcia:0.0 [ 2035.976000] conflict: PCI IO[0->ffff] [ 2035.976000] hwif_request_region: single-byte request for ide2 [ 2035.976000] [<c0257386>] hwif_request_region+0xa6/0xb0 [ 2035.976000] [<c02574bf>] ide_hwif_request_regions+0x12f/0x150 [ 2035.976000] [<c0257177>] init_hwif_default+0x37/0x120 [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<c025e8a9>] probe_hwif+0x29/0x4f0 [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<c025ed85>] probe_hwif_init_with_fixup+0x15/0xa0 [ 2035.976000] [<c0257ea5>] ide_register_hw_with_fixup+0x165/0x1b0 [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<f8b07163>] idecs_register+0x83/0xd0 [ide_cs] [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<f8b071c0>] outb_mem+0x0/0x10 [ide_cs] [ 2035.976000] [<f8b075e4>] ide_config+0x414/0x790 [ide_cs] [ 2035.976000] [<f8b071c0>] outb_mem+0x0/0x10 [ide_cs] [ 2035.976000] [<f8b0f4c8>] pcmcia_device_probe+0xa8/0x160 [pcmcia] [ 2035.976000] [<c025104c>] driver_probe_device+0xbc/0xe0 [ 2035.976000] [<c02510f0>] __driver_attach+0x0/0x80 [ 2035.976000] [<c0251160>] __driver_attach+0x70/0x80 [ 2035.976000] [<c0250369>] bus_for_each_dev+0x69/0x80 [ 2035.976000] [<c0251195>] driver_attach+0x25/0x30 [ 2035.976000] [<c02510f0>] __driver_attach+0x0/0x80 [ 2035.976000] [<c0250968>] bus_add_driver+0x88/0xd0 [ 2035.976000] [<f8b0b00f>] init_ide_cs+0xf/0x11 [ide_cs] [ 2035.976000] [<c0139f32>] sys_init_module+0xf2/0x190 [ 2035.976000] [<c02e3105>] sysenter_past_esp+0x56/0x79 [ 2035.976000] [<c02e007b>] inet6_lookup_listener+0x2b/0x100 [ 2035.976000] ide2: I/O resource 0xF8B0200E-0xF8B0200E not free. [ 2035.976000] ide2: ports already in use, skipping probe [ 2035.976000] conflict: PCI IO[0->ffff] [ 2035.976000] hwif_request_region: single-byte request for ide2 [ 2035.976000] [<c0257386>] hwif_request_region+0xa6/0xb0 [ 2035.976000] [<c02574bf>] ide_hwif_request_regions+0x12f/0x150 [ 2035.976000] [<c0257177>] init_hwif_default+0x37/0x120
[snip 1400 lines more]
-andy
Quoted 47 lines · On Tue, 20 Jun 2006 23:50:36 -0700 Andy Isaacson <[email protected]> wrote:
Quoted 3 lines · Andrew Morton
It's strange (to me) that IDE is requesting a single-byte memory region. Possibly we've broken the
resource.ccode such that it has some off-by-one and is now rejecting single-byte requests.[snip]
Quoted 2 lines
+++
a/kernel/resource.ckernel/resource.c renamed from kernel/resource.c~a +1
-0+ printk("conflict: %s[%Lx->%Lx]\n",[snip]
Quoted 4 lines
Then again, perhaps IDE is broken (as well?), because you don't have any single-byte iomem regions in your 2.6.17-rc6
/proc/iomem. It would be interesting to run this patch in both 2.6.17-rc6 and in 2.6.17-rc6-mm2, see what it says:[snip]
drivers/ide/ide.c static struct resource* hwif_request_reg · line 369
Quoted 3 lines
+++
25-akpm/drivers/ide/ide.cTue Jun 20 15:02:15 2006drivers/ide/ide.c renamed from drivers/ide/ide.c~a +2
-0+printk ("%s: single-byte request\n" , __FUNCTION__); +dump_stack ();With both patches, rc6-mm2 dumps the following.
[ 2034.052000] pccard: PCMCIA card inserted into slot 0 [ 2034.052000] cs: memory probe 0xf0000000-0xf7ffffff: excluding 0xf0000000-0xf7ffffff [ 2034.052000] cs: memory probe 0xd0200000-0xdfffffff: excluding 0xd0200000-0xd11fffff 0xd1a00000-0xd41fffff 0xd4a00000-0xd51fffff 0xd5a00000-0xd61fffff 0xd6a00000-0xd71fffff 0xd7a00000-0xd81fffff 0xd8a00000-0xd91fffff 0xd9a00000-0xda1fffff 0xdaa00000-0xdb1fffff 0xdba00000-0xdc1fffff 0xdca00000-0xdd1fffff 0xdda00000-0xde1fffff 0xdea00000-0xdf1fffff 0xdfa00000-0xe01fffff [ 2034.060000] pcmcia: registering new device pcmcia0.0 [ 2034.060000] PM: Adding info for pcmcia:0.0 [ 2035.976000] conflict: PCI IO[0->ffff] [ 2035.976000] hwif_request_region: single-byte request for ide2 [ 2035.976000] [<c0257386>] hwif_request_region+0xa6/0xb0 [ 2035.976000] [<c02574bf>] ide_hwif_request_regions+0x12f/0x150 [ 2035.976000] [<c0257177>] init_hwif_default+0x37/0x120 [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<c025e8a9>] probe_hwif+0x29/0x4f0 [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<c025ed85>] probe_hwif_init_with_fixup+0x15/0xa0 [ 2035.976000] [<c0257ea5>] ide_register_hw_with_fixup+0x165/0x1b0 [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<f8b07163>] idecs_register+0x83/0xd0 [ide_cs] [ 2035.976000] [<f8b070b0>] idecs_mmio_fixup+0x0/0x30 [ide_cs] [ 2035.976000] [<f8b071c0>] outb_mem+0x0/0x10 [ide_cs] [ 2035.976000] [<f8b075e4>] ide_config+0x414/0x790 [ide_cs] [ 2035.976000] [<f8b071c0>] outb_mem+0x0/0x10 [ide_cs] [ 2035.976000] [<f8b0f4c8>] pcmcia_device_probe+0xa8/0x160 [pcmcia] [ 2035.976000] [<c025104c>] driver_probe_device+0xbc/0xe0 [ 2035.976000] [<c02510f0>] __driver_attach+0x0/0x80 [ 2035.976000] [<c0251160>] __driver_attach+0x70/0x80 [ 2035.976000] [<c0250369>] bus_for_each_dev+0x69/0x80 [ 2035.976000] [<c0251195>] driver_attach+0x25/0x30
Quoted 8 lines
[ 2035.976000] [<c02510f0>] __driver_attach+0x0/0x80 [ 2035.976000] [<c0250968>] bus_add_driver+0x88/0xd0 [ 2035.976000] [<f8b0b00f>] init_ide_cs+0xf/0x11 [ide_cs] [ 2035.976000] [<c0139f32>] sys_init_module+0xf2/0x190 [ 2035.976000] [<c02e3105>] sysenter_past_esp+0x56/0x79 [ 2035.976000] [<c02e007b>] inet6_lookup_listener+0x2b/0x100 [ 2035.976000] ide2: I/O resource 0xF8B0200E-0xF8B0200E not free. [ 2035.976000] ide2: ports already in use, skipping probe
hm. It appears to have decided that 0 < 0xF8B0200E < 0xffff, which is clever of it.
Does it help if you set CONFIG_RESOURCES_32BIT?
Quoted 5 lines · Andrew Morton
Quoted 5 lines
[ 2034.060000] pcmcia: registering new device pcmcia0.0 [ 2034.060000] PM: Adding info for pcmcia:0.0 [ 2035.976000] conflict: PCI IO[0->ffff] [ 2035.976000] hwif_request_region: single-byte request for ide2 [ 2035.976000] [<c0257386>] hwif_request_region+0xa6/0xb0
[snip]
Quoted 7 lines
Quoted 2 lines
[ 2035.976000] ide2: I/O resource 0xF8B0200E-0xF8B0200E not free. [ 2035.976000] ide2: ports already in use, skipping probehm. It appears to have decided that 0 <
0xF8B0200E<0xffff, which is clever of it.Does it help if you set
CONFIG_RESOURCES_32BIT?
Nope, same conflict with CONFIG_RESOURCES_32BIT set. You're right, it is deciding that 0xF8B0200E conflicts with that range:
conflict: PCI IO[0->ffff] conflicts with ide2[f8b3c00e->f8b3c00e]
Looking at the code, I don't understand how this could have worked in -rc6; __request_resource hasn't changed, and it says
167 if (end < start)
168 return root;
169 if (start < root->start)
170 return root;
171 if (end > root->end)
172 return root;If root-> start == 0 and root->end == 0xffff, we should always hit line 172, unless sign extension is in effect... and all the variables are unsigned long in -rc6, so that doesn't make sense.
Rebooting into -rc6 with some debugging...
-andy
Quoted 23 lines · Andy Isaacson
Quoted 7 lines
Quoted 2 lines
[ 2035.976000] ide2: I/O resource 0xF8B0200E-0xF8B0200E not free. [ 2035.976000] ide2: ports already in use, skipping probehm. It appears to have decided that 0 <
0xF8B0200E<0xffff, which is clever of it.Does it help if you set
CONFIG_RESOURCES_32BIT?Nope, same conflict with
CONFIG_RESOURCES_32BITset. You're right, it is deciding that0xF8B0200Econflicts with that range:conflict: PCI IO[0->ffff] conflicts with ide2[f8b3c00e->f8b3c00e]
Looking at the code, I don't understand how this could have worked in -rc6;
__request_resourcehasn't changed, and it says167 if (end < start) 168 return root; 169 if (start < root->start) 170 return root; 171 if (end > root->end) 172 return root;
Quoted 5 lines
If root-> start == 0 and
root->end==0xffff, we should always hit line 172, unless sign extension is in effect... and all the variables are unsigned long in -rc6, so that doesn't make sense.Rebooting into -rc6 with some debugging...
So 2.6.17-rc6 plus the conflict-printer patch and the ide-single-byte-request patch does the following (booted with the PCMCIA/CF adapter in by accident, and I'm using a different CF card now, but it seems to have done the right thing):
cs: memory probe 0xf0000000-0xf7ffffff: excluding 0xf0000000-0xf7ffffff
cs: memory probe 0xd0200000-0xdfffffff: excluding 0xd0200000-0xd11fffff 0xd1a00000-0xd41fffff 0xd4a00000-0xd51fffff 0xd5a00000-0xd61fffff 0xd6a00000-0xd71fffff 0xd7a00000-0xd81fffff 0xd8a00000-0xd91fffff 0xd9a00000-0xda1fffff 0xdaa00000-0xdb1fffff 0xdba00000-0xdc1fffff 0xdca00000-0xdd1fffff 0xdda00000-0xde1fffff 0xdea00000-0xdf1fffff 0xdfa00000-0xe01fffff
pcmcia: registering new device pcmcia0.0
pcmcia: Detected deprecated PCMCIA ioctl usage from process: cardmgr.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
cs: IO port probe 0x100-0x4ff: excluding 0x170-0x177 0x370-0x377 0x4d0-0x4d7
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0xa00-0xaff: clean.
conflict: PCI Bus #02[3000->7fff] conflicts with ide2[310e->310e]
conflict: pcmcia_socket0[3100->310f] conflicts with ide2[310e->310e]hwif_request_region: single-byte request for ide2
<c0242abe> hwif_request_region+0x9e/0xa0 <c0242bbf> ide_hwif_request_regions+0xff/0x120
<c0249c90> ide_undecoded_slave+0x0/0xc0 <c0249d79> probe_hwif+0x29/0x4f0
<c0249c90> ide_undecoded_slave+0x0/0xc0 <c024a255> probe_hwif_init_with_fixup+0x15/0xa0
<c0243556> ide_register_hw_with_fixup+0x166/0x1b0 <c0249c90> ide_undecoded_slave+0x0/0xc0
<f8a8612b> idecs_register+0x7b/0xb0 [ide_cs] <c0249c90> ide_undecoded_slave+0x0/0xc0
<f8a865a2> ide_config+0x442/0x6c0 [ide_cs] <f8ab348e> pcmcia_device_probe+0x6e/0x100 [pcmcia]
<c023ca1c> driver_probe_device+0xbc/0xe0 <c023cac0> __driver_attach+0x0/0x80
<c023cb30> __driver_attach+0x70/0x80 <c023bd69> bus_for_each_dev+0x69/0x80
<c01e5723> kobject_set_name+0x43/0xe0 <c023cb65> driver_attach+0x25/0x30
<c023cac0> __driver_attach+0x0/0x80 <c023c338> bus_add_driver+0x88/0xd0
<c023d077> driver_register+0x97/0xa0 <c023cfc0> klist_devices_get+0x0/0x10
<c023cfd0> klist_devices_put+0x0/0x10 <f8ab32f7> pcmcia_register_driver+0x17/0x50 [pcmcia]
<f894200f> init_ide_cs+0xf/0x11 [ide_cs] <c0136da2> sys_init_module+0xf2/0x180
<c0102f2f> sysenter_past_esp+0x54/0x75
conflict: PCI Bus #02[3000->7fff] conflicts with ide2[3100->3107]
conflict: pcmcia_socket0[3100->310f] conflicts with ide2[3100->3107]
Probing IDE interface ide2...
hde: LEXAR ATA FLASH, CFA DISK drive
ide2 at 0x3100-0x3107,0x310e on irq 3
hde: max request size: 128KiB
hde: 64256 sectors (32 MB) w/1KiB Cache, CHS=1004/2/32
hde: cache flushes not supported
hde: hde1
ide-cs: hde: Vpp = 0.0
I hope somebody who understands resource.c better than me is reading this, because I'm pretty much out of time to spend reading code. (Happy to test patches, of course.)
-andy
Quoted 30 lines · Andy Isaacson
Quoted 5 lines · Andrew Morton
Quoted 5 lines
[ 2034.060000] pcmcia: registering new device pcmcia0.0 [ 2034.060000] PM: Adding info for pcmcia:0.0 [ 2035.976000] conflict: PCI IO[0->ffff] [ 2035.976000] hwif_request_region: single-byte request for ide2 [ 2035.976000] [<c0257386>] hwif_request_region+0xa6/0xb0[snip]
Quoted 7 lines
Quoted 2 lines
[ 2035.976000] ide2: I/O resource 0xF8B0200E-0xF8B0200E not free. [ 2035.976000] ide2: ports already in use, skipping probehm. It appears to have decided that 0 <
0xF8B0200E<0xffff, which is clever of it.Does it help if you set
CONFIG_RESOURCES_32BIT?Nope, same conflict with
CONFIG_RESOURCES_32BITset. You're right, it is deciding that0xF8B0200Econflicts with that range:conflict: PCI IO[0->ffff] conflicts with ide2[f8b3c00e->f8b3c00e]
Looking at the code, I don't understand how this could have worked in -rc6;
__request_resourcehasn't changed, and it says167 if (end < start) 168 return root; 169 if (start < root->start) 170 return root; 171 if (end > root->end) 172 return root;
Quoted 4 lines
If root-> start == 0 and
root->end==0xffff, we should always hit line 172, unless sign extension is in effect... and all the variables are unsigned long in -rc6, so that doesn't make sense.
I think this makes sense. We are hitting line 172 in case of -mm because f8b3c00e is not a valid io port at all. Maximum valid value can be 0xffff. So _request_region considers this to be a conflict and returns.
It succeeds in -rc6 because ide code is requesting a valid ioport region ide2[310e->310e].
So __request_region() code seems to be fine. Problem seems to be that why do we get an invalid ioport range in following call.
addr = hwif->io_ports[IDE_CONTROL_OFFSET];
Either hwif pointer is bad or somehow the location it is pointing to is corrupt or something else. Can you do some more tracing on hwif.
Thanks
Vivek