sk98lin extremely slow transfer rate ASUS P5P800(2.6.17.7)
I am experiencing a very slow(32Kbytes per second) transfer rate on an ASUS P5P800 mobo. This occurs on a special case where I am sending individual 32Kbyte messages from a second server.
I suspect the hardware, but am not sure how to come up with a 'good' regression test for this issue.
Configurations I have tried:
1. If I swap out the ethernet adapter(tried a intel 10/100 and intel 10/100/1000) the transfer rate jumps up into the MBytes / second.
2. If I do 'other' network activity on the box, like scp'ing' files around, the transfer rate for my 32Kbyte packets goes up into the Mbytes / second. So I am a little baffled with the behavior.
3. If I just 'scp' files around of various sizes the transfer rate goes up into the Mbytes / second.
some of the relevant dmesg information:
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
...
eth0: network connection up using port A
speed: 1000
autonegotiation: yes
duplex mode: full
flowctrl: symmetric
role: slave
irq moderation: disabled
scatter-gather: disabled
tx-checksum: disabled
rx-checksum: disabled
lspci -vvv output for the ethernet adapter:
02:05.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit
Ethernet Controller (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size 04
Interrupt: pin A routed to IRQ 7
Region 0: Memory at fbffc000 (32-bit, non-prefetchable)
[size=16K]
Region 1: I/O ports at e800 [size=256]
Expansion ROM at f0000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
The Marvel ethernet adapter is connected to a Linksys SD2005 10/100/1000 switch.
Any ideas why it would be doing this or a 'good' test for me to try?
Sean
Quoted 12 lines · On Thu, 03 Aug 2006 08:40:01 -0700 Sean Bruno <[email protected]> wrote:
I am experiencing a very slow(32Kbytes per second) transfer rate on an ASUS P5P800 mobo. This occurs on a special case where I am sending individual 32Kbyte messages from a second server.
I suspect the hardware, but am not sure how to come up with a 'good' regression test for this issue.
Configurations I have tried:
1. If I swap out the ethernet adapter(tried a intel 10/100 and intel 10/100/1000) the transfer rate jumps up into the MBytes / second.
Quoted 7 lines
2. If I do 'other' network activity on the box, like scp'ing' files around, the transfer rate for my 32Kbyte packets goes up into the Mbytes / second. So I am a little baffled with the behavior.
3. If I just 'scp' files around of various sizes the transfer rate goes up into the Mbytes / second.
Which driver skge or sk98lin are you using? Sk98lin driver is being obsoleted.
Quoted 1 line · Stephen Hemminger
skge
I am using sk98lin under 2.6.17.7 ... should I give skge a shot?
Sean
Quoted 7 lines · On Thu, 03 Aug 2006 09:46:36 -0700 Sean Bruno <[email protected]> wrote:
Quoted 1 line · Stephen Hemminger
skge
I am using sk98lin under 2.6.17.7 ... should I give skge a shot?
Sean
Yes, we will fix skge, sk98lin probably will stay busted...
You might be seeing checksum errors or flow control issues.
Look at ethtool stats (ethtool -S eth0)
and try with hardware checksumming off (ethtool -K rx off tx off)
Quoted 1 line · Stephen Hemminger
e
ty
I have built skge and loaded it in leu of sk98lin and re-running my failure case.
sean
Quoted 10 lines · Sean Bruno
Quoted 1 line · Stephen Hemminger
e
ty
I have built skge and loaded it in leu of sk98lin and re-running my failure case.
sean
-
Thanks for the guidance. Simply using the skge driver instead has resolved the issue I was seeing.
Sean